SupportConsoleDevelopersStart a trialContact

Chapter 4. Install on disconnected networks

You might need to install the multicluster engine operator on Red Hat OpenShift Container Platform clusters that are not connected to the Internet. The procedure to install on a disconnected engine requires some of the same steps as the connected installation.

Important: You must install multicluster engine for Kubernetes on a cluster that does not have Red Hat Advanced Cluster Management for Kubernetes earlier than 2.5 installed. The multicluster engine for Kubernetes cannot co-exist with Red Hat Advanced Cluster Management for Kubernetes on versions earlier than 2.5 because they provide some of the same management components. It is recommended that you install multicluster engine for Kubernetes on a cluster that has never previously installed Red Hat Advanced Cluster Management. If you are using Red Hat Advanced Cluster Management for Kubernetes at version 2.5.0 or later then multicluster engine for Kubernetes will already be installed on the cluster with it.

You must download copies of the packages to access them during the installation, rather than accessing them directly from the network during the installation.

4.1. Prerequisites

You must meet the following requirements before you install The multicluster engine operator:

  • Red Hat OpenShift Container Platform version 4.8 or later must be deployed in your environment, and you must be logged in with the command line interface (CLI).

  • You need access to the catalog.redhat.com.

    Note: For managing bare metal clusters, you must have OpenShift Container Platform version 4.8 or later.

    See the OpenShift Container Platform version 4.10, OpenShift Container Platform version 4.8.

  • Your Red Hat OpenShift Container Platform CLI must be version 4.8 or later, and configured to run oc commands. See Getting started with the CLI for information about installing and configuring the Red Hat OpenShift CLI.
  • Your Red Hat OpenShift Container Platform permissions must allow you to create a namespace.
  • You must have a workstation with Internet connection to download the dependencies for the operator.

4.2. Confirm your OpenShift Container Platform installation

  • You must have a supported OpenShift Container Platform version, including the registry and storage services, installed and working in your cluster. For information about OpenShift Container Platform version 4.8, see OpenShift Container Platform documentation.

  • When and if you are connected, you can ensure that the OpenShift Container Platform cluster is set up correctly. Access the OpenShift Container Platform web console.

    Run the kubectl -n openshift-console get route command to access the OpenShift Container Platform web console. See the following example output: 

    openshift-console          console             console-openshift-console.apps.new-coral.purple-chesterfield.com                       console              https   reencrypt/Redirect     None

    The console URL in this example is: https:// console-openshift-console.apps.new-coral.purple-chesterfield.com. Open the URL in your browser and check the result.

    If the console URL displays console-openshift-console.router.default.svc.cluster.local, set the value for openshift_master_default_subdomain when you install OpenShift Container Platform.

4.3. Installing in a disconnected environment

Important: You need to download the required images to a mirroring registry to install the operators in a disconnected environment. Without the download, you might receive ImagePullBackOff errors during your deployment.

Follow these steps to install the multicluster engine for Kubernetes operator in a disconnected environment:

  1. Create a mirror registry. If you do not already have a mirror registry, create one by completing the procedure in the Mirroring images for a disconnected installation topic of the Red Hat OpenShift Container Platform documentation.

    If you already have a mirror registry, you can configure and use your existing one.

  2. Note: For bare metal only, you need to provide the certificate information for the disconnected registry in your install-config.yaml file. To access the image in a protected disconnected registry, you must provide the certificate information so the multicluster engine for Kubernetes operator can access the registry.

    1. Copy the certificate information from the registry.
    2. Open the install-config.yaml file in an editor.
    3. Find the entry for additionalTrustBundle: |.

    4. Add the certificate information after the additionalTrustBundle line. The resulting content should look similar to the following example: 

      additionalTrustBundle: |
  -----BEGIN CERTIFICATE-----
  certificate_content
  -----END CERTIFICATE-----
sshKey: >-

  3. Important: Additional mirrors for disconnected image registries are needed if the following Governance policies are required:

    • Container Security Operator policy: The images are located in the source registry.redhat.io/quay.
    • Compliance operator policy: The images are located in the source registry.redhat.io/compliance

    • Gatekeeper operator policy: The images are located in the source registry.redhat.io/rhacm2

      See the following example of mirrors lists for all three operators: 

        - mirrors:
      - <your_registry>/rhacm2
      source: registry.redhat.io/rhacm2
    - mirrors:
      - <your_registry>/quay
      source: registry.redhat.io/quay
    - mirrors:
      - <your_registry>/compliance
      source: registry.redhat.io/compliance
  4. Save the install-config.yaml file.

  5. Create a YAML file that contains the ImageContentSourcePolicy with the name rhacm-policy.yaml. Note: If you modify this on a running cluster, it causes a rolling restart of all nodes. 

    apiVersion: operator.openshift.io/v1alpha1
kind: ImageContentSourcePolicy
metadata:
  name: mce-repo
spec:
  repositoryDigestMirrors:
  - mirrors:
    - mirror.registry.com:5000/multicluster-engine
    source: registry.redhat.io/multicluster-engine

  6. Apply the ImageContentSourcePolicy file by entering the following command: 

    oc apply -f mce-policy.yaml

  7. Enable the disconnected Operator Lifecycle Manager Red Hat Operators and Community Operators.

    the multicluster engine for Kubernetes operator is included in the Operator Lifecycle Manager Red Hat Operator catalog.

  8. Configure the disconnected Operator Lifecycle Manager for the Red Hat Operator catalog. Follow the steps in the Using Operator Lifecycle Manager on restricted networks topic of the Red Hat OpenShift Container Platform documentation.
  9. Now that you have the image in the disconnected Operator Lifecycle Manager, continue to install the multicluster engine for Kubernetes operator for Kubernetes from the Operator Lifecycle Manager catalog.

See Installing while connected online for the required steps.

Red Hat logoGithubRedditYoutubeTwitter

Learn

Try, buy, & sell

Communities

About Red Hat Documentation

We help Red Hat users innovate and achieve their goals with our products and services with content they can trust.

Making open source more inclusive

Red Hat is committed to replacing problematic language in our code, documentation, and web properties. For more details, see the Red Hat Blog.

About Red Hat

We deliver hardened solutions that make it easier for enterprises to work across platforms and environments, from the core datacenter to the network edge.

© 2024 Red Hat, Inc.