Search

5.4. Logical Volume Administration

download PDF
This section describes the commands that perform the various aspects of logical volume administration.

5.4.1. Creating Linear Logical Volumes

To create a logical volume, use the lvcreate command. If you do not specify a name for the logical volume, the default name lvol# is used where # is the internal number of the logical volume.
When you create a logical volume, the logical volume is carved from a volume group using the free extents on the physical volumes that make up the volume group. Normally logical volumes use up any space available on the underlying physical volumes on a next-free basis. Modifying the logical volume frees and reallocates space in the physical volumes.
As of the Red Hat Enterprise Linux 6.3 release, you can use LVM to create, display, rename, use, and remove RAID logical volumes. For information on RAID logical volumes, see Section 5.4.16, “RAID Logical Volumes”.
The following command creates a logical volume 10 gigabytes in size in the volume group vg1.
# lvcreate -L 10G vg1
The default unit for logical volume size is megabytes. The following command creates a 1500 MB linear logical volume named testlv in the volume group testvg, creating the block device /dev/testvg/testlv.
# lvcreate -L 1500 -n testlv testvg
The following command creates a 50 gigabyte logical volume named gfslv from the free extents in volume group vg0.
# lvcreate -L 50G -n gfslv vg0
You can use the -l argument of the lvcreate command to specify the size of the logical volume in extents. You can also use this argument to specify the percentage of the volume group to use for the logical volume. The following command creates a logical volume called mylv that uses 60% of the total space in volume group testvg.
# lvcreate -l 60%VG -n mylv testvg
You can also use the -l argument of the lvcreate command to specify the percentage of the remaining free space in a volume group as the size of the logical volume. The following command creates a logical volume called yourlv that uses all of the unallocated space in the volume group testvg.
# lvcreate -l 100%FREE -n yourlv testvg
You can use -l argument of the lvcreate command to create a logical volume that uses the entire volume group. Another way to create a logical volume that uses the entire volume group is to use the vgdisplay command to find the "Total PE" size and to use those results as input to the lvcreate command.
The following commands create a logical volume called mylv that fills the volume group named testvg.
# vgdisplay testvg | grep "Total PE"
Total PE              10230
# lvcreate -l 10230 testvg -n mylv
The underlying physical volumes used to create a logical volume can be important if the physical volume needs to be removed, so you may need to consider this possibility when you create the logical volume. For information on removing a physical volume from a volume group, see Section 5.3.7, “Removing Physical Volumes from a Volume Group”.
To create a logical volume to be allocated from a specific physical volume in the volume group, specify the physical volume or volumes at the end at the lvcreate command line. The following command creates a logical volume named testlv in volume group testvg allocated from the physical volume /dev/sdg1,
# lvcreate -L 1500 -ntestlv testvg /dev/sdg1
You can specify which extents of a physical volume are to be used for a logical volume. The following example creates a linear logical volume out of extents 0 through 24 of physical volume /dev/sda1 and extents 50 through 124 of physical volume /dev/sdb1 in volume group testvg.
# lvcreate -l 100 -n testlv testvg /dev/sda1:0-24 /dev/sdb1:50-124
The following example creates a linear logical volume out of extents 0 through 25 of physical volume /dev/sda1 and then continues laying out the logical volume at extent 100.
# lvcreate -l 100 -n testlv testvg /dev/sda1:0-25:100-
The default policy for how the extents of a logical volume are allocated is inherit, which applies the same policy as for the volume group. These policies can be changed using the lvchange command. For information on allocation policies, see Section 5.3.1, “Creating Volume Groups”.
Red Hat logoGithubRedditYoutubeTwitter

Learn

Try, buy, & sell

Communities

About Red Hat Documentation

We help Red Hat users innovate and achieve their goals with our products and services with content they can trust.

Making open source more inclusive

Red Hat is committed to replacing problematic language in our code, documentation, and web properties. For more details, see the Red Hat Blog.

About Red Hat

We deliver hardened solutions that make it easier for enterprises to work across platforms and environments, from the core datacenter to the network edge.

© 2024 Red Hat, Inc.