Chapter 5. Configuring a single node RHHI for Virtualization deployment

1. Log into the Web Console

   Browse to the the Web Console management interface of the first hyperconverged host, for example, https://node1.example.com:9090/, and log in with the credentials you created in the previous section.

2. Start the deployment wizard

   1. Click Virtualization Hosted Engine and click Start underneath Hyperconverged.

      

      The Gluster Configuration window opens.

   2. Click the Run Gluster Wizard for Single Node button.

      

      The Gluster Deployment window opens in single node mode.

3. Specify hyperconverged host

   Specify the back-end FQDN on the storage network of the hyperconverged host and click Next.

   

4. Specify volumes

   Specify the volumes to create.

   

   Name

   Specify the name of the volume to be created.

   Volume Type

   Specify a Distribute volume type. Only distributed volumes are supported for single node deployments.

   Brick Dirs

   The directory that contains this volume’s bricks.

5. Specify bricks

   Specify the bricks to create.

   

   RAID

   Specify the RAID configuration to use. This should match the RAID configuration of your host. Supported values are raid5, raid6, and jbod. Setting this option ensures that your storage is correctly tuned for your RAID configuration.

   Stripe Size

   Specify the RAID stripe size in KB. Do not enter units, only the number. This can be ignored for jbod configurations.

   Disk Count

   Specify the number of data disks in a RAID volume. This can be ignored for jbod configurations.

   LV Name

   The name of the logical volume to be created. This is pre-filled with the name that you specified on the previous page of the wizard.

   Device

   Specify the raw device you want to use. Red Hat recommends an unpartitioned device.

   1. With multipath devices

      If the environment has multipath devices for the Gluster deployment from the cockpit, use multipath WWIDs.
      For example:

      /dev/mapper/3600508b1001caab032303683327a6a2e
      instead of /dev/sdb

   2. Without the multipath devices

      If there are no multipath devices in the environment. Blacklist these devices.

      Note

      Blacklist: Listing of specific devices that will not be considered for multipath.

      There are different ways to blacklist the device. For more information, refer to RHEL 7 DM Multipath, chapter 4.2.

      • To blacklist the device /dev/sdb

        1. Create a directory: /etc/multipath/conf.d/

        2. Create a file under this directory with the following content: blacklist {
           devnodes "<device>"
           }
           For example:

           [root@ ~]# cat /etc/multipath/conf.d/99-custom-multipath.conf
           blacklist {
               devnodes "sdb"
           }

           Important

           Local disks should not have multipath names. Use lsblk command to check for multipath names.
           

           If there are multipath names on the disks, after blacklisting the disks,reboot the hosts.

   Size

   Specify the size of the logical volume to create in GB. Do not enter units, only the number. This number should be the same for all bricks in a replicated set. Arbiter bricks can be smaller than other bricks in their replication set.

   Mount Point

   The mount point for the logical volume. This is pre-filled with the brick directory that you specified on the previous page of the wizard.

   Thinp

   This option is enabled and volumes are thinly provisioned by default, except for the engine volume, which must be thickly provisioned.

   Enable Dedupe & Compression

   Specify whether to provision the volume using VDO for compression and deduplication at deployment time.

   Logical Size (GB)

   Specify the logical size of the VDO volume. This can be up to 10 times the size of the physical volume, with an absolute maximum logical size of 4 PB.

   Configure LV Cache

   Optionally, check this checkbox to configure a small, fast SSD device as a logical volume cache for a larger, slower logical volume. Add the device path to the SSD field, the size to the LV Size (GB) field, and set the Cache Mode used by the device.

   Warning

   To avoid data loss when using write-back mode, Red Hat recommends using two separate SSD/NVMe devices. Configuring the two devices in a RAID-1 configuration (via software or hardware), significantly reduces the potential of data loss from lost writes.

   For further information about lvmcache configuration, see Red Hat Enterprise Linux 7 LVM Administration.

6. Review and edit configuration

   Review the contents of the generated configuration file and click Edit to modify the file, and Save to keep your changes.

   Click Deploy when you are satisfied with the configuration file.

   

7. Wait for deployment to complete

   You can watch the deployment process in the text field.

   The window displays Successfully deployed gluster when complete.

   Click Continue to Hosted Engine Deployment and continue the deployment process with the instructions in Section 5.2, “Deploy the Hosted Engine on a single node using the Web Console”.

Procedure

1. Open the Hosted Engine Deployment wizard

   If you continued directly from the end of Configure Red Hat Gluster Storage on a single node, the wizard is already open.

   Otherwise:

   1. Click Virtualization Hosted Engine.
   2. Click Start underneath Hyperconverged.

   3. Click Use existing configuration.

      Important

      If the previous deployment attempt failed, click Clean up instead of Use existing configuration to discard the previous attempt and start from scratch.

2. Specify virtual machine details

   

   1. Enter the following details:

      Engine VM FQDN

      The fully qualified domain name to be used for the Hosted Engine virtual machine, for example, engine.example.com.

      MAC Address

      The MAC address associated with the Engine VM FQDN.

      Important

      The pre-populated MAC address must be replaced.

      Root password

      The root password to be used for the Hosted Engine virtual machine.

   2. Click Next. Your FQDNs are validated before the next screen appears.

3. Specify virtualization management details

   1. Enter the password to be used by the admin account in the Administration Portal. You can also specify notification behaviour here.

      
   2. Click Next.

4. Review virtual machine configuration

   1. Ensure that the details listed on this tab are correct. Click Back to correct any incorrect information.

      
   2. Click Prepare VM.

   3. Wait for virtual machine preparation to complete.

      

      If preparation does not occur successfully, see Viewing Hosted Engine deployment errors.

   4. Click Next.

5. Specify storage for the Hosted Engine virtual machine

   1. Specify the back-end address and location of the engine volume.

      
   2. Click Next.

6. Finalize Hosted Engine deployment

   1. Review your deployment details and verify that they are correct.

      Note

      The responses you provided during configuration are saved to an answer file to help you reinstall the hosted engine if necessary. The answer file is created at /etc/ovirt-hosted-engine/answers.conf by default. This file should not be modified manually without assistance from Red Hat Support.

      
   2. Click Finish Deployment.

7. Wait for deployment to complete

   This takes up to 30 minutes.

   The window displays the following when complete.

   
   Important

   If deployment does not complete successfully, see Viewing Hosted Engine deployment errors.

   Click Close.

8. Verify hosted engine deployment

   Browse to the Administration Portal (for example, http://engine.example.com/ovirt-engine) and verify that you can log in using the administrative credentials you configured earlier. Click Dashboard and look for your hosts, storage domains, and virtual machines.