Chapter 7. Configuring physical switches for OpenStack Networking


This chapter documents the common physical switch configuration steps required for OpenStack Networking. Vendor-specific configuration is included for certain switches.

7.1. Planning your physical network environment

The physical network adapters in your OpenStack nodes carry different types of network traffic, such as instance traffic, storage data, or authentication requests. The type of traffic these NICs carry affects how you must configure the ports on the physical switch.

First, you must decide which physical NICs oFn your Compute node you want to carry which types of traffic. Then, when the NIC is cabled to a physical switch port, you must configure the switch port to allow trunked or general traffic.

For example, the following diagram depicts a Compute node with two NICs, eth0 and eth1. Each NIC is cabled to a Gigabit Ethernet port on a physical switch, with eth0 carrying instance traffic, and eth1 providing connectivity for OpenStack services:

Figure 7.1. Sample network layout

Sample network layout
Note

This diagram does not include any additional redundant NICs required for fault tolerance.

Additional resources

7.2. Configuring a Cisco Catalyst switch

7.2.1. About trunk ports

With OpenStack Networking you can connect instances to the VLANs that already exist on your physical network. The term trunk is used to describe a port that allows multiple VLANs to traverse through the same port. Using these ports, VLANs can span across multiple switches, including virtual switches. For example, traffic tagged as VLAN110 in the physical network reaches the Compute node, where the 8021q module directs the tagged traffic to the appropriate VLAN on the vSwitch.

7.2.2. Configuring trunk ports for a Cisco Catalyst switch

  • If using a Cisco Catalyst switch running Cisco IOS, you might use the following configuration syntax to allow traffic for VLANs 110 and 111 to pass through to your instances.

    This configuration assumes that your physical node has an ethernet cable connected to interface GigabitEthernet1/0/12 on the physical switch.

    Important

    These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

    interface GigabitEthernet1/0/12
      description Trunk to Compute Node
      spanning-tree portfast trunk
      switchport trunk encapsulation dot1q
      switchport mode trunk
      switchport trunk native vlan 2
      switchport trunk allowed vlan 2,110,111

    Use the following list to understand these parameters:

    FieldDescription

    interface GigabitEthernet1/0/12

    The switch port that the NIC of the X node connects to. Ensure that you replace the GigabitEthernet1/0/12 value with the correct port value for your environment. Use the show interface command to view a list of ports.

    description Trunk to Compute Node

    A unique and descriptive value that you can use to identify this interface.

    spanning-tree portfast trunk

    If your environment uses STP, set this value to instruct Port Fast that this port is used to trunk traffic.

    switchport trunk encapsulation dot1q

    Enables the 802.1q trunking standard (rather than ISL). This value varies depending on the configuration that your switch supports.

    switchport mode trunk

    Configures this port as a trunk port, rather than an access port, meaning that it allows VLAN traffic to pass through to the virtual switches.

    switchport trunk native vlan 2

    Set a native VLAN to instruct the switch where to send untagged (non-VLAN) traffic.

    switchport trunk allowed vlan 2,110,111

    Defines which VLANs are allowed through the trunk.

7.2.3. About access ports

Not all NICs on your Compute node carry instance traffic, and so you do not need to configure all NICs to allow multiple VLANs to pass through. Access ports require only one VLAN, and might fulfill other operational requirements, such as transporting management traffic or Block Storage data. These ports are commonly known as access ports and usually require a simpler configuration than trunk ports.

7.2.4. Configuring access ports for a Cisco Catalyst switch

  • Using the example from the Figure 7.1, “Sample network layout” diagram, GigabitEthernet1/0/13 (on a Cisco Catalyst switch) is configured as an access port for eth1.

    In this configuration,your physical node has an ethernet cable connected to interface GigabitEthernet1/0/12 on the physical switch.

    Important

    These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

    interface GigabitEthernet1/0/13
     description Access port for Compute Node
     switchport mode access
     switchport access vlan 200
     spanning-tree portfast

    These settings are described below:

    FieldDescription

    interface GigabitEthernet1/0/13

    The switch port that the NIC of the X node connects to. Ensure that you replace the GigabitEthernet1/0/12 value with the correct port value for your environment. Use the show interface command to view a list of ports.

    description Access port for Compute Node

    A unique and descriptive value that you can use to identify this interface.

    switchport mode access

    Configures this port as an access port, rather than a trunk port.

    switchport access vlan 200

    Configures the port to allow traffic on VLAN 200. You must configure your Compute node with an IP address from this VLAN.

    spanning-tree portfast

    If using STP, set this value to instruct STP not to attempt to initialize this as a trunk, allowing for quicker port handshakes during initial connections (such as server reboot).

7.2.5. About LACP port aggregation

You can use Link Aggregation Control Protocol (LACP) to bundle multiple physical NICs together to form a single logical channel. Also known as 802.3ad (or bonding mode 4 in Linux), LACP creates a dynamic bond for load-balancing and fault tolerance. You must configure LACP at both physical ends: on the physical NICs, and on the physical switch ports.

Additional resources

7.2.6. Configuring LACP on the physical NIC

You can configure Link Aggregation Control Protocol (LACP) on a physical NIC.

Procedure

  1. Edit the /home/stack/network-environment.yaml file:

    - type: linux_bond
      name: bond1
      mtu: 9000
      bonding_options:{get_param: BondInterfaceOvsOptions};
      members:
        - type: interface
          name: nic3
          mtu: 9000
          primary: true
        - type: interface
          name: nic4
          mtu: 9000
  2. Configure the Open vSwitch bridge to use LACP:

    BondInterfaceOvsOptions:
        "mode=802.3ad"

Additional resources

7.2.7. Configuring LACP for a Cisco Catalyst switch

In this example, the Compute node has two NICs using VLAN 100:

Procedure

  1. Physically connect both NICs on the Compute node to the switch (for example, ports 12 and 13).
  2. Create the LACP port channel:

    interface port-channel1
      switchport access vlan 100
      switchport mode access
      spanning-tree guard root
  3. Configure switch ports 12 (Gi1/0/12) and 13 (Gi1/0/13):

    sw01# config t
    Enter configuration commands, one per line.  End with CNTL/Z.
    
    sw01(config) interface GigabitEthernet1/0/12
       switchport access vlan 100
       switchport mode access
       speed 1000
       duplex full
       channel-group 10 mode active
       channel-protocol lacp
    
    interface GigabitEthernet1/0/13
      switchport access vlan 100
      switchport mode access
      speed 1000
      duplex full
      channel-group 10 mode active
      channel-protocol lacp
  4. Review your new port channel. The resulting output lists the new port-channel Po1, with member ports Gi1/0/12 and Gi1/0/13:

    sw01# show etherchannel summary
    <snip>
    
    Number of channel-groups in use: 1
    Number of aggregators:           1
    
    Group  Port-channel  Protocol    Ports
    ------+-------------+-----------+-----------------------------------------------
    1      Po1(SD)         LACP      Gi1/0/12(D)  Gi1/0/13(D)
    Note

    Remember to apply your changes by copying the running-config to the startup-config: copy running-config startup-config.

7.2.8. About MTU settings

You must adjust your MTU size for certain types of network traffic. For example, jumbo frames (9000 bytes) are required for certain NFS or iSCSI traffic.

Note

You must change MTU settings from end-to-end on all hops that the traffic is expected to pass through, including any virtual switches.

7.2.9. Configuring MTU settings for a Cisco Catalyst switch

Complete the steps in this example procedure to enable jumbo frames on your Cisco Catalyst 3750 switch.

  1. Review the current MTU settings:

    sw01# show system mtu
    
    System MTU size is 1600 bytes
    System Jumbo MTU size is 1600 bytes
    System Alternate MTU size is 1600 bytes
    Routing MTU size is 1600 bytes
  2. MTU settings are changed switch-wide on 3750 switches, and not for individual interfaces. Run the following commands to configure the switch to use jumbo frames of 9000 bytes. You might prefer to configure the MTU settings for individual interfaces, if your switch supports this feature.

    sw01# config t
    Enter configuration commands, one per line.  End with CNTL/Z.
    
    sw01(config)# system mtu jumbo 9000
    Changes to the system jumbo MTU will not take effect until the next reload is done
    Note

    Remember to save your changes by copying the running-config to the startup-config: copy running-config startup-config.

  3. Reload the switch to apply the change.

    Important

    Reloading the switch causes a network outage for any devices that are dependent on the switch. Therefore, reload the switch only during a scheduled maintenance period.

    sw01# reload
    Proceed with reload? [confirm]
  4. After the switch reloads, confirm the new jumbo MTU size.

    The exact output may differ depending on your switch model. For example, System MTU might apply to non-Gigabit interfaces, and Jumbo MTU might describe all Gigabit interfaces.

    sw01# show system mtu
    
    System MTU size is 1600 bytes
    System Jumbo MTU size is 9000 bytes
    System Alternate MTU size is 1600 bytes
    Routing MTU size is 1600 bytes

7.2.10. About LLDP discovery

The ironic-python-agent service listens for LLDP packets from connected switches. The collected information can include the switch name, port details, and available VLANs. Similar to Cisco Discovery Protocol (CDP), LLDP assists with the discovery of physical hardware during the director introspection process.

7.2.11. Configuring LLDP for a Cisco Catalyst switch

Procedure

  1. Run the lldp run command to enable LLDP globally on your Cisco Catalyst switch:

    sw01# config t
    Enter configuration commands, one per line.  End with CNTL/Z.
    
    sw01(config)# lldp run
  2. View any neighboring LLDP-compatible devices:

    sw01# show lldp neighbor
    Capability codes:
        (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
        (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
    
    Device ID           Local Intf     Hold-time  Capability      Port ID
    DEP42037061562G3     Gi1/0/11       180        B,T             422037061562G3:P1
    
    Total entries displayed: 1
Note

Remember to save your changes by copying the running-config to the startup-config: copy running-config startup-config.

7.3. Configuring a Cisco Nexus switch

7.3.1. About trunk ports

With OpenStack Networking you can connect instances to the VLANs that already exist on your physical network. The term trunk is used to describe a port that allows multiple VLANs to traverse through the same port. Using these ports, VLANs can span across multiple switches, including virtual switches. For example, traffic tagged as VLAN110 in the physical network reaches the Compute node, where the 8021q module directs the tagged traffic to the appropriate VLAN on the vSwitch.

7.3.2. Configuring trunk ports for a Cisco Nexus switch

  • If using a Cisco Nexus you might use the following configuration syntax to allow traffic for VLANs 110 and 111 to pass through to your instances.

    This configuration assumes that your physical node has an ethernet cable connected to interface Ethernet1/12 on the physical switch.

    Important

    These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

    interface Ethernet1/12
      description Trunk to Compute Node
      switchport mode trunk
      switchport trunk allowed vlan 2,110,111
      switchport trunk native vlan 2
    end

7.3.3. About access ports

Not all NICs on your Compute node carry instance traffic, and so you do not need to configure all NICs to allow multiple VLANs to pass through. Access ports require only one VLAN, and might fulfill other operational requirements, such as transporting management traffic or Block Storage data. These ports are commonly known as access ports and usually require a simpler configuration than trunk ports.

7.3.4. Configuring access ports for a Cisco Nexus switch

Procedure

  • Using the example from the Figure 7.1, “Sample network layout” diagram, Ethernet1/13 (on a Cisco Nexus switch) is configured as an access port for eth1. This configuration assumes that your physical node has an ethernet cable connected to interface Ethernet1/13 on the physical switch.

    Important

    These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

    interface Ethernet1/13
     description Access port for Compute Node
     switchport mode access
     switchport access vlan 200

7.3.5. About LACP port aggregation

You can use Link Aggregation Control Protocol (LACP) to bundle multiple physical NICs together to form a single logical channel. Also known as 802.3ad (or bonding mode 4 in Linux), LACP creates a dynamic bond for load-balancing and fault tolerance. You must configure LACP at both physical ends: on the physical NICs, and on the physical switch ports.

Additional resources

7.3.6. Configuring LACP on the physical NIC

You can configure Link Aggregation Control Protocol (LACP) on a physical NIC.

Procedure

  1. Edit the /home/stack/network-environment.yaml file:

    - type: linux_bond
      name: bond1
      mtu: 9000
      bonding_options:{get_param: BondInterfaceOvsOptions};
      members:
        - type: interface
          name: nic3
          mtu: 9000
          primary: true
        - type: interface
          name: nic4
          mtu: 9000
  2. Configure the Open vSwitch bridge to use LACP:

    BondInterfaceOvsOptions:
        "mode=802.3ad"

Additional resources

7.3.7. Configuring LACP for a Cisco Nexus switch

In this example, the Compute node has two NICs using VLAN 100:

Procedure

  1. Physically connect the Compute node NICs to the switch (for example, ports 12 and 13).
  2. Confirm that LACP is enabled:

    (config)# show feature | include lacp
    lacp                  1         enabled
  3. Configure ports 1/12 and 1/13 as access ports, and as members of a channel group.

    Depending on your deployment, you can deploy trunk interfaces rather than access interfaces.

    For example, for Cisco UCI the NICs are virtual interfaces, so you might prefer to configure access ports exclusively. Often these interfaces contain VLAN tagging configurations.

    interface Ethernet1/13
     description Access port for Compute Node
     switchport mode access
     switchport access vlan 200
     channel-group 10 mode active
    
    interface Ethernet1/13
     description Access port for Compute Node
     switchport mode access
     switchport access vlan 200
     channel-group 10 mode active
Note

When you use PXE to provision nodes on Cisco switches, you might need to set the options no lacp graceful-convergence and no lacp suspend-individual to bring up the ports and boot the server. For more information, see your Cisco switch documentation.

7.3.8. About MTU settings

You must adjust your MTU size for certain types of network traffic. For example, jumbo frames (9000 bytes) are required for certain NFS or iSCSI traffic.

Note

You must change MTU settings from end-to-end on all hops that the traffic is expected to pass through, including any virtual switches.

7.3.9. Configuring MTU settings for a Cisco Nexus 7000 switch

Apply MTU settings to a single interface on 7000-series switches.

Procedure

  • Run the following commands to configure interface 1/12 to use jumbo frames of 9000 bytes:

    interface ethernet 1/12
      mtu 9216
      exit

7.3.10. About LLDP discovery

The ironic-python-agent service listens for LLDP packets from connected switches. The collected information can include the switch name, port details, and available VLANs. Similar to Cisco Discovery Protocol (CDP), LLDP assists with the discovery of physical hardware during the director introspection process.

7.3.11. Configuring LLDP for a Cisco Nexus 7000 switch

Procedure

  • You can enable LLDP for individual interfaces on Cisco Nexus 7000-series switches:

    interface ethernet 1/12
      lldp transmit
      lldp receive
      no lacp suspend-individual
      no lacp graceful-convergence
    
    interface ethernet 1/13
      lldp transmit
      lldp receive
      no lacp suspend-individual
      no lacp graceful-convergence
Note

Remember to save your changes by copying the running-config to the startup-config: copy running-config startup-config.

7.4. Configuring a Cumulus Linux switch

7.4.1. About trunk ports

With OpenStack Networking you can connect instances to the VLANs that already exist on your physical network. The term trunk is used to describe a port that allows multiple VLANs to traverse through the same port. Using these ports, VLANs can span across multiple switches, including virtual switches. For example, traffic tagged as VLAN110 in the physical network reaches the Compute node, where the 8021q module directs the tagged traffic to the appropriate VLAN on the vSwitch.

7.4.2. Configuring trunk ports for a Cumulus Linux switch

This configuration assumes that your physical node has transceivers connected to switch ports swp1 and swp2 on the physical switch.

Important

These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

Procedure

  • Use the following configuration syntax to allow traffic for VLANs 100 and 200 to pass through to your instances.

    auto bridge
    iface bridge
      bridge-vlan-aware yes
      bridge-ports glob swp1-2
      bridge-vids 100 200

7.4.3. About access ports

Not all NICs on your Compute node carry instance traffic, and so you do not need to configure all NICs to allow multiple VLANs to pass through. Access ports require only one VLAN, and might fulfill other operational requirements, such as transporting management traffic or Block Storage data. These ports are commonly known as access ports and usually require a simpler configuration than trunk ports.

7.4.4. Configuring access ports for a Cumulus Linux switch

This configuration assumes that your physical node has an ethernet cable connected to the interface on the physical switch. Cumulus Linux switches use eth for management interfaces and swp for access/trunk ports.

Important

These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

Procedure

  • Using the example from the Figure 7.1, “Sample network layout” diagram, swp1 (on a Cumulus Linux switch) is configured as an access port.

    auto bridge
    iface bridge
      bridge-vlan-aware yes
      bridge-ports glob swp1-2
      bridge-vids 100 200
    
    
    auto swp1
    iface swp1
      bridge-access 100
    
    
    auto swp2
    iface swp2
      bridge-access 200

7.4.5. About LACP port aggregation

You can use Link Aggregation Control Protocol (LACP) to bundle multiple physical NICs together to form a single logical channel. Also known as 802.3ad (or bonding mode 4 in Linux), LACP creates a dynamic bond for load-balancing and fault tolerance. You must configure LACP at both physical ends: on the physical NICs, and on the physical switch ports.

Additional resources

7.4.6. About MTU settings

You must adjust your MTU size for certain types of network traffic. For example, jumbo frames (9000 bytes) are required for certain NFS or iSCSI traffic.

Note

You must change MTU settings from end-to-end on all hops that the traffic is expected to pass through, including any virtual switches.

7.4.7. Configuring MTU settings for a Cumulus Linux switch

Procedure

  • This example enables jumbo frames on your Cumulus Linux switch.

    auto swp1
    iface swp1
      mtu 9000
    Note

    Remember to apply your changes by reloading the updated configuration: sudo ifreload -a

7.4.8. About LLDP discovery

The ironic-python-agent service listens for LLDP packets from connected switches. The collected information can include the switch name, port details, and available VLANs. Similar to Cisco Discovery Protocol (CDP), LLDP assists with the discovery of physical hardware during the director introspection process.

7.4.9. Configuring LLDP for a Cumulus Linux switch

By default, the LLDP service lldpd runs as a daemon and starts when the switch boots.

Procedure

  • To view all LLDP neighbors on all ports/interfaces, run the following command:

    cumulus@switch$ netshow lldp
    Local Port  Speed  Mode         Remote Port   Remote Host Summary
    ----------  ---    ---------    -----  -----  ----------- --------
    eth0        10G    Mgmt         ====   swp6   mgmt-sw     IP: 10.0.1.11/24
    swp51       10G    Interface/L3 ====   swp1   spine01     IP: 10.0.0.11/32
    swp52       10G    Interface/L  ====   swp1   spine02     IP: 10.0.0.11/32

7.5. Configuring a Extreme Exos switch

7.5.1. About trunk ports

With OpenStack Networking you can connect instances to the VLANs that already exist on your physical network. The term trunk is used to describe a port that allows multiple VLANs to traverse through the same port. Using these ports, VLANs can span across multiple switches, including virtual switches. For example, traffic tagged as VLAN110 in the physical network reaches the Compute node, where the 8021q module directs the tagged traffic to the appropriate VLAN on the vSwitch.

7.5.2. Configuring trunk ports on an Extreme Networks EXOS switch

If using an X-670 series switch, refer to the following example to allow traffic for VLANs 110 and 111 to pass through to your instances.

Important

These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

Procedure

  • This configuration assumes that your physical node has an ethernet cable connected to interface 24 on the physical switch. In this example, DATA and MNGT are the VLAN names.

    #create vlan DATA tag 110
    #create vlan MNGT tag 111
    #configure vlan DATA add ports 24 tagged
    #configure vlan MNGT add ports 24 tagged

7.5.3. About access ports

Not all NICs on your Compute node carry instance traffic, and so you do not need to configure all NICs to allow multiple VLANs to pass through. Access ports require only one VLAN, and might fulfill other operational requirements, such as transporting management traffic or Block Storage data. These ports are commonly known as access ports and usually require a simpler configuration than trunk ports.

7.5.4. Configuring access ports for an Extreme Networks EXOS switch

This configuration assumes that your physical node has an ethernet cable connected to interface 10 on the physical switch.

Important

These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

Procedure

  • In this configuration example, on a Extreme Networks X-670 series switch, 10 is used as an access port for eth1.

    create vlan VLANNAME tag NUMBER
    configure vlan Default delete ports PORTSTRING
    configure vlan VLANNAME add ports PORTSTRING untagged

    For example:

    #create vlan DATA tag 110
    #configure vlan Default delete ports 10
    #configure vlan DATA add ports 10 untagged

7.5.5. About LACP port aggregation

You can use Link Aggregation Control Protocol (LACP) to bundle multiple physical NICs together to form a single logical channel. Also known as 802.3ad (or bonding mode 4 in Linux), LACP creates a dynamic bond for load-balancing and fault tolerance. You must configure LACP at both physical ends: on the physical NICs, and on the physical switch ports.

Additional resources

7.5.6. Configuring LACP on the physical NIC

You can configure Link Aggregation Control Protocol (LACP) on a physical NIC.

Procedure

  1. Edit the /home/stack/network-environment.yaml file:

    - type: linux_bond
      name: bond1
      mtu: 9000
      bonding_options:{get_param: BondInterfaceOvsOptions};
      members:
        - type: interface
          name: nic3
          mtu: 9000
          primary: true
        - type: interface
          name: nic4
          mtu: 9000
  2. Configure the Open vSwitch bridge to use LACP:

    BondInterfaceOvsOptions:
        "mode=802.3ad"

Additional resources

7.5.7. Configuring LACP on an Extreme Networks EXOS switch

Procedure

7.5.8. About MTU settings

You must adjust your MTU size for certain types of network traffic. For example, jumbo frames (9000 bytes) are required for certain NFS or iSCSI traffic.

Note

You must change MTU settings from end-to-end on all hops that the traffic is expected to pass through, including any virtual switches.

7.5.9. Configuring MTU settings on an Extreme Networks EXOS switch

Procedure

  • Run the commands in this example to enable jumbo frames on an Extreme Networks EXOS switch and configure support for forwarding IP packets with 9000 bytes:

    enable jumbo-frame ports PORTSTRING
    configure ip-mtu 9000 vlan VLANNAME

    Example

    # enable jumbo-frame ports 11
    # configure ip-mtu 9000 vlan DATA

7.5.10. About LLDP discovery

The ironic-python-agent service listens for LLDP packets from connected switches. The collected information can include the switch name, port details, and available VLANs. Similar to Cisco Discovery Protocol (CDP), LLDP assists with the discovery of physical hardware during the director introspection process.

7.5.11. Configuring LLDP settings on an Extreme Networks EXOS switch

Procedure

  • In this example, LLDP is enabled on an Extreme Networks EXOS switch. 11 represents the port string:
enable lldp ports 11

7.6. Configuring a Juniper EX Series switch

7.6.1. About trunk ports

With OpenStack Networking you can connect instances to the VLANs that already exist on your physical network. The term trunk is used to describe a port that allows multiple VLANs to traverse through the same port. Using these ports, VLANs can span across multiple switches, including virtual switches. For example, traffic tagged as VLAN110 in the physical network reaches the Compute node, where the 8021q module directs the tagged traffic to the appropriate VLAN on the vSwitch.

7.6.2. Configuring trunk ports for a Juniper EX Series switch

Procedure

  • If using a Juniper EX series switch running Juniper JunOS, use the following configuration syntax to allow traffic for VLANs 110 and 111 to pass through to your instances.

    This configuration assumes that your physical node has an ethernet cable connected to interface ge-1/0/12 on the physical switch.

    Important

    These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

     ge-1/0/12 {
              description Trunk to Compute Node;
                  unit 0 {
                      family ethernet-switching {
                          port-mode trunk;
                          vlan {
                              members [110 111];
                               }
                          native-vlan-id 2;
                      }
                  }
    }

7.6.3. About access ports

Not all NICs on your Compute node carry instance traffic, and so you do not need to configure all NICs to allow multiple VLANs to pass through. Access ports require only one VLAN, and might fulfill other operational requirements, such as transporting management traffic or Block Storage data. These ports are commonly known as access ports and usually require a simpler configuration than trunk ports.

7.6.4. Configuring access ports for a Juniper EX Series switch

This example on, a Juniper EX series switch, shows ge-1/0/13 as an access port for eth1.

+

Important

These values are examples. You must change the values in this example to match those in your environment. Copying and pasting these values into your switch configuration without adjustment can result in an unexpected outage.

Procedure

This configuration assumes that your physical node has an ethernet cable connected to interface ge-1/0/13 on the physical switch.

+

 ge-1/0/13 {
          description Access port for Compute Node
              unit 0 {
                  family ethernet-switching {
                      port-mode access;
                      vlan {
                          members 200;
                           }
                      native-vlan-id 2;
                  }
              }
}

7.6.5. About LACP port aggregation

You can use Link Aggregation Control Protocol (LACP) to bundle multiple physical NICs together to form a single logical channel. Also known as 802.3ad (or bonding mode 4 in Linux), LACP creates a dynamic bond for load-balancing and fault tolerance. You must configure LACP at both physical ends: on the physical NICs, and on the physical switch ports.

Additional resources

7.6.6. Configuring LACP on the physical NIC

You can configure Link Aggregation Control Protocol (LACP) on a physical NIC.

Procedure

  1. Edit the /home/stack/network-environment.yaml file:

    - type: linux_bond
      name: bond1
      mtu: 9000
      bonding_options:{get_param: BondInterfaceOvsOptions};
      members:
        - type: interface
          name: nic3
          mtu: 9000
          primary: true
        - type: interface
          name: nic4
          mtu: 9000
  2. Configure the Open vSwitch bridge to use LACP:

    BondInterfaceOvsOptions:
        "mode=802.3ad"

Additional resources

7.6.7. Configuring LACP for a Juniper EX Series switch

In this example, the Compute node has two NICs using VLAN 100.

Procedure

  1. Physically connect the Compute node’s two NICs to the switch (for example, ports 12 and 13).
  2. Create the port aggregate:

    chassis {
        aggregated-devices {
            ethernet {
                device-count 1;
            }
        }
    }
  3. Configure switch ports 12 (ge-1/0/12) and 13 (ge-1/0/13) to join the port aggregate ae1:

    interfaces {
        ge-1/0/12 {
            gigether-options {
                802.3ad ae1;
            }
        }
        ge-1/0/13 {
            gigether-options {
                802.3ad ae1;
                }
            }
    }
    Note

    For Red Hat OpenStack Platform director deployments, in order to PXE boot from the bond, you must configure one of the bond members as lacp force-up toensure that only one bond member comes up during introspection and first boot. The bond member that you configure with lacp force-up must be the same bond member that has the MAC address in instackenv.json (the MAC address known to ironic must be the same MAC address configured with force-up).

  4. Enable LACP on port aggregate ae1:

    interfaces {
        ae1 {
            aggregated-ether-options {
                lacp {
                    active;
                }
            }
        }
    }
  5. Add aggregate ae1 to VLAN 100:

    interfaces {
        ae1 {
            vlan-tagging;
            native-vlan-id 2;
            unit 100 {
                vlan-id 100;
            }
        }
    }
  6. Review your new port channel. The resulting output lists the new port aggregate ae1 with member ports ge-1/0/12 and ge-1/0/13:

    > show lacp statistics interfaces ae1
    
    Aggregated interface: ae1
    LACP Statistics: LACP Rx LACP Tx Unknown Rx Illegal Rx
    ge-1/0/12 0 0 0 0
    ge-1/0/13 0 0 0 0
    Note

    Remember to apply your changes by running the commit command.

7.6.8. About MTU settings

You must adjust your MTU size for certain types of network traffic. For example, jumbo frames (9000 bytes) are required for certain NFS or iSCSI traffic.

Note

You must change MTU settings from end-to-end on all hops that the traffic is expected to pass through, including any virtual switches.

7.6.9. Configuring MTU settings for a Juniper EX Series switch

This example enables jumbo frames on your Juniper EX4200 switch.

Note

The MTU value is calculated differently depending on whether you are using Juniper or Cisco devices. For example, 9216 on Juniper would equal to 9202 for Cisco. The extra bytes are used for L2 headers, where Cisco adds this automatically to the MTU value specified, but the usable MTU will be 14 bytes smaller than specified when using Juniper. So in order to support an MTU of 9000 on the VLANs, the MTU of 9014 would have to be configured on Juniper.

Procedure

  1. For Juniper EX series switches, MTU settings are set for individual interfaces. These commands configure jumbo frames on the ge-1/0/14 and ge-1/0/15 ports:

    set interfaces ge-1/0/14 mtu 9216
    set interfaces ge-1/0/15 mtu 9216
    Note

    Remember to save your changes by running the commit command.

  2. If using a LACP aggregate, you will need to set the MTU size there, and not on the member NICs. For example, this setting configures the MTU size for the ae1 aggregate:

     set interfaces ae1 mtu 9216

7.6.10. About LLDP discovery

The ironic-python-agent service listens for LLDP packets from connected switches. The collected information can include the switch name, port details, and available VLANs. Similar to Cisco Discovery Protocol (CDP), LLDP assists with the discovery of physical hardware during the director introspection process.

7.6.11. Configuring LLDP for a Juniper EX Series switch

You can enable LLDP globally for all interfaces, or just for individual ones.

Procedure

  • Use the following too enable LLDP globally on your Juniper EX 4200 switch:

    lldp {
    	interface all{
    		enable;
    	}
    	}
    }
  • Use the following to enable LLDP for the single interface ge-1/0/14:

    lldp {
    	interface ge-1/0/14{
    		enable;
    	}
    	}
    }
    Note

    Remember to apply your changes by running the commit command.

Red Hat logoGithubRedditYoutubeTwitter

Learn

Try, buy, & sell

Communities

About Red Hat Documentation

We help Red Hat users innovate and achieve their goals with our products and services with content they can trust.

Making open source more inclusive

Red Hat is committed to replacing problematic language in our code, documentation, and web properties. For more details, see the Red Hat Blog.

About Red Hat

We deliver hardened solutions that make it easier for enterprises to work across platforms and environments, from the core datacenter to the network edge.

© 2024 Red Hat, Inc.