Este contenido no está disponible en el idioma seleccionado.
B.15. No Guest Virtual Machines are Present when libvirtd is Started
- Symptom
- The libvirt daemon is successfully started, but no guest virtual machines appear to be present.
# virsh list --all Id Name State ---------------------------------------------------- # - Investigation
- There are various possible causes of this problem. Performing these tests will help to determine the cause of this situation:
- Verify KVM kernel modules
- Verify that KVM kernel modules are inserted in the kernel:
# lsmod | grep kvm kvm_intel 121346 0 kvm 328927 1 kvm_intelIf you are using an AMD machine, verify thekvm_amdkernel modules are inserted in the kernel instead, using the similar commandlsmod | grep kvm_amdin the root shell.If the modules are not present, insert them using themodprobe <modulename>command.Note
Although it is uncommon, KVM virtualization support may be compiled into the kernel. In this case, modules are not needed. - Verify virtualization extensions
- Verify that virtualization extensions are supported and enabled on the host:
# egrep "(vmx|svm)" /proc/cpuinfo flags : fpu vme de pse tsc ... svm ... skinit wdt npt lbrv svm_lock nrip_save flags : fpu vme de pse tsc ... svm ... skinit wdt npt lbrv svm_lock nrip_saveEnable virtualization extensions in your hardware's firmware configuration within the BIOS setup. Refer to your hardware documentation for further details on this. - Verify client URI configuration
- Verify that the URI of the client is configured as desired:
# virsh uri vbox:///systemFor example, this message shows the URI is connected to the VirtualBox hypervisor, not QEMU, and reveals a configuration error for a URI that is otherwise set to connect to a QEMU hypervisor. If the URI was correctly connecting to QEMU, the same message would appear instead as:# virsh uri qemu:///systemThis situation occurs when there are other hypervisors present, which libvirt may speak to by default.
- Solution
- After performing these tests, use the following command to view a list of guest virtual machines:
# virsh list --all
'%20d='M201.5%20305.5c-13.8%200-24.9-11.1-24.9-24.6%200-13.8%2011.1-24.9%2024.9-24.9%2013.6%200%2024.6%2011.1%2024.6%2024.9%200%2013.6-11.1%2024.6-24.6%2024.6zM504%20256c0%20137-111%20248-248%20248S8%20393%208%20256%20119%208%20256%208s248%20111%20248%20248zm-132.3-41.2c-9.4%200-17.7%203.9-23.8%2010-22.4-15.5-52.6-25.5-86.1-26.6l17.4-78.3%2055.4%2012.5c0%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.3%2024.9-24.9s-11.1-24.9-24.9-24.9c-9.7%200-18%205.8-22.1%2013.8l-61.2-13.6c-3-.8-6.1%201.4-6.9%204.4l-19.1%2086.4c-33.2%201.4-63.1%2011.3-85.5%2026.8-6.1-6.4-14.7-10.2-24.1-10.2-34.9%200-46.3%2046.9-14.4%2062.8-1.1%205-1.7%2010.2-1.7%2015.5%200%2052.6%2059.2%2095.2%20132%2095.2%2073.1%200%20132.3-42.6%20132.3-95.2%200-5.3-.6-10.8-1.9-15.8%2031.3-16%2019.8-62.5-14.9-62.5zM302.8%20331c-18.2%2018.2-76.1%2017.9-93.6%200-2.2-2.2-6.1-2.2-8.3%200-2.5%202.5-2.5%206.4%200%208.6%2022.8%2022.8%2087.3%2022.8%20110.2%200%202.5-2.2%202.5-6.1%200-8.6-2.2-2.2-6.1-2.2-8.3%200zm7.7-75c-13.6%200-24.6%2011.1-24.6%2024.9%200%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.1%2024.9-24.6%200-13.8-11-24.9-24.9-24.9z'/%3e%3c/svg%3e){kind=small}