Ce contenu n'est pas disponible dans la langue sélectionnée.
3.9. Adding a Cluster Service to the Cluster
To add a cluster service to the cluster, follow the steps in this section. The starting point of the procedure is at the cluster-specific page that you navigate to from Choose a cluster to administer displayed on the tab.
- At the detailed menu for the cluster (below themenu), click . Clicking causes the display of services in the center of the page and causes the display of menu items for services configuration: , , and .
- To configure any service other than a virtual machine service, Click Add a Service page to be displayed.. Clicking causes the
- On the Add a Service page, at the text box, type the name of the service.
Note
Use a descriptive name that clearly distinguishes the service from other services in the cluster. - Below thetext box, enter the following parameters for this service.
- not checked, the service must be started manually any time the cluster comes up from the stopped state.— When the checkbox is checked, the service is started automatically when a cluster is started and running. If the checkbox is
- Table C.3, “File System”, and the table of GFS resource parameters, Table C.4, “GFS”.— Setting this option will release NFS locks on a file system in a soft attempt to unmount a file system, which may be necessary if your filesystem is exported via NFS and occasionally fails to unmount (either during shutdown or service relocation). You can also enable NFS daemon and lock workarounds for individual file system resources, which will result in a hard attempt to unmount a file system, as described in the table of file system resource parameters,
Run exclusive
. You can override this option by manual start or relocate operations.- — List of cluster members to try in the event that a service fails. For information on configuring a failover domain with Conga, refer to
- In addition, you can specify theand the .
- Add a resource to the service; click only to this service. The process of adding a local resource is the same as adding a global resource described in Section 3.8, “Adding Cluster Resources”. Adding a global resource adds a resource that has been previously added as a global resource (refer to Section 3.8, “Adding Cluster Resources”).. Clicking causes the display of two drop-down boxes: and . Adding a new local resource adds a resource that is available
- At the drop-down box of either Section 3.8, “Adding Cluster Resources”.)or , select the resource to add and configure it according to the options presented. (The options are the same as described in
Note
If you are adding a Samba-service resource, connect a Samba-service resource directly to the service, not to a resource within a service. - If you want to add resources to that resource, click. Clicking causes the display of additional options to local and global resources. You can continue adding children resources to the resource to suit your requirements. To view children resources, click the triangle icon to the left of .
- When you have completed adding resources to the service, and have completed adding children resources to resources, click. Clicking causes a progress page to be displayed followed by a page displaying the added service (and other services).
Note
To verify the existence of the IP service resource used in a cluster service, you must use the
/sbin/ip addr list
command on a cluster node. The following output shows the /sbin/ip addr list
command executed on a node running a cluster service:
1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP> mtu 1356 qdisc pfifo_fast qlen 1000 link/ether 00:05:5d:9a:d8:91 brd ff:ff:ff:ff:ff:ff inet 10.11.4.31/22 brd 10.11.7.255 scope global eth0 inet6 fe80::205:5dff:fe9a:d891/64 scope link inet 10.11.4.240/22 scope global secondary eth0 valid_lft forever preferred_lft forever
Note
To configure a virtual machine service, after clicking Table C.23, “Virtual Machine”. When you have completed adding the virtual machine resource parameters, click .
you can click . Enter the virtual machine resource parameters. For a description of the virtual machine parameters, refer to