このコンテンツは選択した言語では利用できません。
Global File System
Red Hat Enterprise Linux 4
Red Hat Global File System
Edition 1.1
Abstract
This book provides information about installing, configuring, and maintaining Red Hat GFS (Red Hat Global File System) for Red Hat Enterprise Linux 4.
Introduction
Welcome to the Global File System Configuration and Administration document. This book provides information about installing, configuring, and maintaining Red Hat GFS (Red Hat Global File System). Red Hat GFS depends on the cluster infrastructure of Red Hat Cluster Suite. For information about Red Hat Cluster Suite refer to Red Hat Cluster Suite Overview and Configuring and Managing a Red Hat Cluster.
HTML and PDF versions of all the official Red Hat Enterprise Linux manuals and release notes are available online at http://www.redhat.com/docs/.
1. Audience
This book is intended primarily for Linux system administrators who are familiar with the following activities:
- Linux system administration procedures, including kernel configuration
- Installation and configuration of shared storage networks, such as Fibre Channel SANs
2. Related Documentation
For more information about using Red Hat Enterprise Linux, refer to the following resources:
- Red Hat Enterprise Linux Installation Guide — Provides information regarding installation of Red Hat Enterprise Linux.
- Red Hat Enterprise Linux Introduction to System Administration — Provides introductory information for new Red Hat Enterprise Linux system administrators.
- Red Hat Enterprise Linux System Administration Guide — Provides more detailed information about configuring Red Hat Enterprise Linux to suit your particular needs as a user.
- Red Hat Enterprise Linux Reference Guide — Provides detailed information suited for more experienced users to reference when needed, as opposed to step-by-step instructions.
- Red Hat Enterprise Linux Security Guide — Details the planning and the tools involved in creating a secured computing environment for the data center, workplace, and home.
For more information about Red Hat Cluster Suite for Red Hat Enterprise Linux, refer to the following resources:
- Red Hat Cluster Suite Overview — Provides a high level overview of the Red Hat Cluster Suite.
- Configuring and Managing a Red Hat Cluster — Provides information about installing, configuring and managing Red Hat Cluster components.
- LVM Administrator's Guide: Configuration and Administration — Provides a description of the Logical Volume Manager (LVM), including information on running LVM in a clustered environment.
- Using GNBD with Global File System — Provides an overview on using Global Network Block Device (GNBD) with Red Hat GFS.
- Using Device-Mapper Multipath — Provides information about using the Device-Mapper Multipath feature of Red Hat Enterprise Linux.
- Linux Virtual Server Administration — Provides information on configuring high-performance systems and services with the Linux Virtual Server (LVS).
- Red Hat Cluster Suite Release Notes — Provides information about the current release of Red Hat Cluster Suite.
Red Hat Cluster Suite documentation and other Red Hat documents are available in HTML and PDF versions online at the following location:
3. Feedback
If you spot a typo, or if you have thought of a way to make this manual better, we would love to hear from you. Please submit a report in Bugzilla (http://bugzilla.redhat.com/bugzilla/) against the component
rh-cs
.
Be sure to mention the manual's identifier:
rh-gfsg(EN)-4.8 (2010-03-17T16:33)
By mentioning this manual's identifier, we know exactly which version of the guide you have.
If you have a suggestion for improving the documentation, try to be as specific as possible. If you have found an error, please include the section number and some of the surrounding text so we can find it easily.
4. Recommended References
For additional references about related topics, refer to the following table:
Topic | Reference | Comment |
---|---|---|
Shared Data Clustering and File Systems | Shared Data Clusters by Dilip M. Ranade. Wiley, 2002. | Provides detailed technical information on cluster file system and cluster volume-manager design. |
Storage Area Networks (SANs) | Designing Storage Area Networks: A Practical Reference for Implementing Fibre Channel and IP SANs, Second Edition by Tom Clark. Addison-Wesley, 2003. | Provides a concise summary of Fibre Channel and IP SAN Technology. |
Building SANs with Brocade Fabric Switches by C. Beauchamp, J. Judd, and B. Keo. Syngress, 2001. | Best practices for building Fibre Channel SANs based on the Brocade family of switches, including core-edge topology for large SAN fabrics. | |
Building Storage Networks, Second Edition by Marc Farley. Osborne/McGraw-Hill, 2001. | Provides a comprehensive overview reference on storage networking technologies. | |
Applications and High Availability | Blueprints for High Availability: Designing Resilient Distributed Systems by E. Marcus and H. Stern. Wiley, 2000. | Provides a summary of best practices in high availability. |
Chapter 1. GFS Overview
Red Hat GFS is a cluster file system that is available with Red Hat Cluster Suite. Red Hat GFS nodes are configured and managed with Red Hat Cluster Suite configuration and management tools. Red Hat GFS provides data sharing among GFS nodes in a Red Hat cluster. GFS provides a single, consistent view of the file-system name space across the GFS nodes in a Red Hat cluster. GFS allows applications to install and run without much knowledge of the underlying storage infrastructure. GFS is fully compliant with the IEEE POSIX interface, allowing applications to perform file operations as if they were running on a local file system. Also, GFS provides features that are typically required in enterprise environments, such as quotas, multiple journals, and multipath support.
GFS provides a versatile method of networking your storage according to the performance, scalability, and economic needs of your storage environment. This chapter provides some very basic, abbreviated information as background to help you understand GFS. It contains the following sections:
1.1. Performance, Scalability, and Economy
You can deploy GFS in a variety of configurations to suit your needs for performance, scalability, and economy. For superior performance and scalability, you can deploy GFS in a cluster that is connected directly to a SAN. For more economical needs, you can deploy GFS in a cluster that is connected to a LAN with servers that use GNBD (Global Network Block Device).
The following sections provide examples of how GFS can be deployed to suit your needs for performance, scalability, and economy:
Note
The deployment examples in this chapter reflect basic configurations; your needs might require a combination of configurations shown in the examples.
1.1.1. Superior Performance and Scalability
You can obtain the highest shared-file performance when applications access storage directly. The GFS SAN configuration in Figure 1.1, “GFS with a SAN” provides superior file performance for shared files and file systems. Linux applications run directly on GFS nodes. Without file protocols or storage servers to slow data access, performance is similar to individual Linux servers with directly connected storage; yet, each GFS application node has equal access to all data files. GFS supports up to 16 GFS nodes.
Figure 1.1. GFS with a SAN
1.1.2. Performance, Scalability, Moderate Price
Multiple Linux client applications on a LAN can share the same SAN-based data as shown in Figure 1.2, “GFS and GNBD with a SAN”. SAN block storage is presented to network clients as block storage devices by GNBD servers. From the perspective of a client application, storage is accessed as if it were directly attached to the server in which the application is running. Stored data is actually on the SAN. Storage devices and data can be equally shared by network client applications. File locking and sharing functions are handled by GFS for each network client.
Note
Clients implementing ext2 and ext3 file systems can be configured to access their own dedicated slice of SAN storage.
Figure 1.2. GFS and GNBD with a SAN
1.1.3. Economy and Performance
Figure 1.3, “GFS and GNBD with Directly Connected Storage” shows how Linux client applications can take advantage of an existing Ethernet topology to gain shared access to all block storage devices. Client data files and file systems can be shared with GFS on each client. Application failover can be fully automated with Red Hat Cluster Suite.
Figure 1.3. GFS and GNBD with Directly Connected Storage
1.2. GFS Functions
GFS is a native file system that interfaces directly with the VFS layer of the Linux kernel file-system interface. GFS is a cluster file system that employs distributed metadata and multiple journals for optimal operation in a cluster. Cluster management of GFS nodes is managed through Red Hat Cluster Suite. Volume management is managed through CLVM (Cluster Logical Volume Manager). For information about Red Hat Cluster Suite refer to Configuring and Managing a Red Hat Cluster. For information about using CLVM, refer to LVM Administrator's Guide.
Note
CLVM is a cluster-wide implementation of LVM, enabled by the CLVM daemon,
clvmd
running in a Red Hat Cluster Suite cluster. The daemon makes it possible to use LVM2 to manage logical volumes across a cluster, allowing all nodes in the cluster to share the logical volumes.
GFS provides the following main functions:
- Making a File System
- Mounting a File System
- Unmounting a File System
- GFS Quota Management
- Growing a File System
- Adding Journals to a File System
- Direct I/O
- Data Journaling
- Configuring
atime
Updates - Suspending Activity on a File System
- Displaying Extended GFS Information and Statistics
- Repairing a File System
- Context-Dependent Path Names (CDPN)
1.3. GFS Software Subsystems
Table 1.1, “GFS Software Subsystem Components” summarizes the GFS Software subsystems and their components.
Software Subsystem | Components | Description |
---|---|---|
GFS | gfs.ko | Kernel module that implements the GFS file system and is loaded on GFS cluster nodes. |
gfs_fsck | Command that repairs an unmounted GFS file system. | |
gfs_grow | Command that grows a mounted GFS file system. | |
gfs_jadd | Command that adds journals to a mounted GFS file system. | |
gfs_mkfs | Command that creates a GFS file system on a storage device. | |
gfs_quota | Command that manages quotas on a mounted GFS file system. | |
gfs_tool | Command that configures or tunes a GFS file system. This command can also gather a variety of information about the file system. | |
lock_harness.ko | Implements a pluggable lock module interface for GFS that allows for a variety of locking mechanisms to be used (for example, the DLM lock module, lock_dlm.ko ). | |
lock_dlm.ko | A lock module that implements DLM locking for GFS. It plugs into the lock harness, lock_harness.ko and communicates with the DLM lock manager in Red Hat Cluster Suite. | |
lock_gulm.ko | A lock module that implements GULM locking for GFS. It plugs into the lock harness, lock_harness.ko and communicates with the GULM lock manager in Red Hat Cluster Suite. | |
lock_nolock.ko | A lock module for use when GFS is used as a local file system only. It plugs into the lock harness, lock_harness.ko and provides local locking. |
1.4. Before Setting Up GFS
Before you install and set up GFS, note the following key characteristics of your GFS file systems:
- Number of file systems
- Determine how many GFS file systems to create initially. (More file systems can be added later.)
- File-system name
- Determine a unique name for each file system. Each file-system name is required in the form of a parameter variable. For example, this book uses file-system names
gfs1
andgfs2
in some example procedures. - Journals
- Determine the number of journals for your GFS file systems. One journal is required for each node that mounts a GFS file system. Make sure to account for additional journals needed for future expansion.
- GFS nodes
- Determine which nodes in the Red Hat Cluster Suite will mount the GFS file systems.
- GNBD server nodes
- If you are using GNBD, determine how many GNBD server nodes are needed. Note the hostname and IP address of each GNBD server node for setting up GNBD clients later. For information on using GNBD with GFS, see the Using GNBD with Global File System document.
- Storage devices and partitions
- Determine the storage devices and partitions to be used for creating logical volumes (via CLVM) in the file systems.
Chapter 2. System Requirements
This chapter describes the system requirements for Red Hat GFS with Red Hat Enterprise Linux 5 and consists of the following sections:
2.1. Platform Requirements
Table 2.1, “Platform Requirements” shows the platform requirements for GFS.
Operating System | Hardware Architecture | RAM | ||
---|---|---|---|---|
Red Hat Enterprise Linux AS, ES, or WS, Version 4 or later |
| 256 MB, minimum |
2.2. Red Hat Cluster Suite
Red Hat GFS runs with Red Hat Cluster Suite 4.0 or later. The Red Hat Cluster Suite software must be installed on the cluster nodes before you can install and run Red Hat GFS.
Note
Red Hat Cluster Suite 4.0 and later provides the infrastructure for application failover in the cluster and network communication among GFS nodes (and other Red Hat Cluster Suite nodes).
2.3. Fencing
You must configure each GFS node in your Red Hat cluster for at least one form of fencing. Fencing is configured and managed in Red Hat Cluster Suite. For more information about fencing options, refer to Configuring and Managing a Red Hat Cluster.
2.4. Fibre Channel Storage Network
Table 2.2, “Fibre Channel Network Requirements” shows requirements for GFS nodes that are to be connected to a Fibre Channel SAN.
Requirement | Description | ||||||
---|---|---|---|---|---|---|---|
HBA (Host Bus Adapter) | One HBA minimum per GFS node | ||||||
Connection method |
|
2.5. Fibre Channel Storage Devices
Table 2.3, “Fibre Channel Storage Device Requirements” shows requirements for Fibre Channel devices that are to be connected to a GFS cluster.
Requirement | Description | |||||
---|---|---|---|---|---|---|
Device Type |
| |||||
Size |
GFS is based on a 64-bit architecture, which can theoretically accommodate an 8 EB file system. However, the current supported maximum size of a GFS file system is 25 TB. If your system requires GFS file systems larger than 25 TB, contact your Red Hat service representative.
When determining the size of your file system, you should consider your recovery needs. Running the
fsck command on the file system can take a long time and consume a large amount of memory. Additionally, in the event of a disk or disk-subsytem failure, recovery time is limited by the speed of your backup media.
|
2.6. Network Power Switches
You can fence GFS nodes with power switches and fencing agents available with Red Hat Cluster Suite. For more information about fencing with network power switches, refer to Configuring and Managing a Red Hat Cluster.
2.7. Console Access
Make sure that you have console access to each GFS node. Console access to each node ensures that you can monitor nodes and troubleshoot problems.
2.8. Installing GFS
Installing GFS consists of installing Red Hat GFS RPMs on nodes in a Red Hat cluster. Before installing the RPMs, make sure of the following:
- The cluster nodes meet the system requirements described in this chapter.
- You have noted the key characteristics of your GFS configuration (refer to Section 1.4, “Before Setting Up GFS”).
- The correct Red Hat Cluster Suite software is installed in the cluster.
For information on installing RPMS for Red Hat Cluster Suite and Red Hat GFS, see Configuring and Managing a Red Hat Cluster. If you have already installed the appropriate Red Hat Cluster Suite RPMs, follow the procedures that pertain to installing the Red Hat GFS RPMs.
Chapter 3. Getting Started
This chapter describes procedures for initial setup of GFS and contains the following sections:
3.1. Prerequisite Tasks
Before setting up Red Hat GFS, make sure that you have noted the key characteristics of the GFS nodes (refer to Section 1.4, “Before Setting Up GFS”) and have loaded the GFS modules into each GFS node.Also, make sure that the clocks on the GFS nodes are synchronized. It is recommended that you use the Network Time Protocol (NTP) software provided with your Red Hat Enterprise Linux distribution. In addition, if you are using GNBD multipath, make sure that you understand GNBD multipath considerations. For information on GNBD multipath, see the document Using GNBD with Global Filesystem.
Note
The system clocks in GFS nodes must be within a few minutes of each other to prevent unnecessary inode time-stamp updating. Unnecessary inode time-stamp updating severely impacts cluster performance.
3.2. Initial Setup Tasks
Initial GFS setup consists of the following tasks:
- Setting up logical volumes.
- Making a GFS files system.
- Mounting file systems.
Follow these steps to set up GFS initially.
- Using CLVM (Cluster Logical Volume Manager), create a logical volume for each Red Hat GFS file system.
Note
You can useinit.d
scripts included with Red Hat Cluster Suite to automate activating and deactivating logical volumes. For more information aboutinit.d
scripts, refer to Configuring and Managing a Red Hat Cluster. - Create GFS file systems on logical volumes created in Step 1. Choose a unique name for each file system. For more information about creating a GFS file system, refer to Section 4.1, “Making a File System”.Command usage:
gfs_mkfs -p lock_dlm -t ClusterName:FSName -j NumberJournals BlockDevice
- At each node, mount the GFS file systems. For more information about mounting a GFS file system, refer to Section 4.2, “Mounting a File System”.Command usage:
mount -t gfs BlockDevice MountPoint
mount -t gfs -o acl BlockDevice MountPoint
The-o
aclmount
option allows manipulating file ACLs. If a file system is mounted without the
mount option, users are allowed to view ACLs (with-o
aclgetfacl
), but are not allowed to set them (withsetfacl
).Note
You can useinit.d
scripts included with Red Hat Cluster Suite to automate mounting and unmounting GFS file systems. For more information aboutinit.d
scripts, refer to Configuring and Managing a Red Hat Cluster.
Chapter 4. Managing GFS
This chapter describes the tasks and commands for managing GFS and consists of the following sections:
4.1. Making a File System
Once a cluster is set up and running, you can create a GFS file system with the
gfs_mkfs
command. A file system is created on an activated CLVM volume.The following information is required to run the gfs_mkfs
command:
- Lock protocol/module name (for example,
lock_dlm
) - Cluster name
- Number of journals (one journal required for each node that may be mounting the file system)
Usage
gfs_mkfs -pLockProtoName
-tLockTableName
-jNumber BlockDevice
Warning
Make sure that you are very familiar with using the
LockProtoName
and LockTableName
parameters. Improper use of the LockProtoName
and LockTableName
parameters may cause file system or lock space corruption.
LockProtoName
- Specifies the name of the locking protocol (for example,
lock_dlm
) to use. LockTableName
- This parameter has two parts separated by a colon (no spaces) as follows:
ClusterName:FSName
ClusterName
, the name of the Red Hat cluster for which the GFS file system is being created.FSName
, the file-system name, can be 1 to 16 characters long, and the name must be unique among all file systems in the cluster.
Number
- Specifies the number of journals to be created by the
gfs_mkfs
command. One journal is required for each node that mounts the file system. (More journals than are needed can be specified at creation time to allow for future expansion.) BlockDevice
- Specifies a volume.
Examples
In this example,
lock_dlm
is the locking protocol that the file system uses. The cluster name is alpha
, and the file-system name is gfs1
. The file system contains eight journals and is created on /dev/vg01/lvol0
.
gfs_mkfs -p lock_dlm -t alpha:gfs1 -j 8 /dev/vg01/lvol0
In this example, a second
lock_dlm
file system is made, which can be used in cluster alpha
. The file-system name is gfs2
. The file system contains eight journals and is created on /dev/vg01/lvol1
.
gfs_mkfs -p lock_dlm -t alpha:gfs2 -j 8 /dev/vg01/lvol1
Complete Options
Table 4.1, “Command Options:
gfs_mkfs
” describes the gfs_mkfs
command options (flags and parameters).
Flag | Parameter | Description | |||||
---|---|---|---|---|---|---|---|
-b | BlockSize | Sets the file-system block size to BlockSize . Default block size is 4096 bytes. | |||||
-D | Enables debugging output. | ||||||
-h | Help. Displays available options. | ||||||
-J | MegaBytes | Specifies the size of the journal in megabytes. Default journal size is 128 megabytes. The minimum size is 32 megabytes. | |||||
-j | Number |
| |||||
-p | LockProtoName |
| |||||
-O | Prevents the gfs_mkfs command from asking for confirmation before writing the file system. | ||||||
-q | Quiet. Do not display anything. | ||||||
-r | MegaBytes | Specifies the size of the resource groups in megabytes. Default resource group size is 256 megabytes. | |||||
-s | Blocks | Specifies the journal-segment size in file-system blocks. | |||||
-t | LockTableName |
| |||||
-V | Displays command version information. |
4.2. Mounting a File System
Before you can mount a GFS file system, the file system must exist (refer to Section 4.1, “Making a File System”), the volume where the file system exists must be activated, and the supporting clustering and locking systems must be started (refer to Chapter 3, Getting Started and Configuring and Managing a Red Hat Cluster. After those requirements have been met, you can mount the GFS file system as you would any Linux file system.
To manipulate file ACLs, you must mount the file system with the
-o
acl
mount option. If a file system is mounted without the -o
acl
mount option, users are allowed to view ACLs (with getfacl
), but are not allowed to set them (with setfacl
).
Usage
Mounting Without ACL Manipulation
mount -t gfs BlockDevice MountPoint
Mounting With ACL Manipulation
mount -t gfs -o acl BlockDevice MountPoint
-o
acl- GFS-specific option to allow manipulating file ACLs.
BlockDevice
- Specifies the block device where the GFS file system resides.
MountPoint
- Specifies the directory where the GFS file system should be mounted.
Example
In this example, the GFS file system on
/dev/vg01/lvol0
is mounted on the /gfs1
directory.
mount -t gfs /dev/vg01/lvol0 /gfs1
Complete Usage
mount -t gfsBlockDevice MountPoint
-ooption
The
-o option
argument consists of GFS-specific options (refer to Table 4.2, “GFS-Specific Mount Options”) or acceptable standard Linux mount -o
options, or a combination of both. Multiple option
parameters are separated by a comma and no spaces.
Note
The
mount
command is a Linux system command. In addition to using GFS-specific options described in this section, you can use other, standard, mount
command options (for example, -r
). For information about other Linux mount
command options, see the Linux mount
man page.
Table 4.2, “GFS-Specific Mount Options” describes the available GFS-specific
-o option
values that can be passed to GFS at mount time.
Option | Description | ||
---|---|---|---|
acl | Allows manipulating file ACLs. If a file system is mounted without the acl mount option, users are allowed to view ACLs (with getfacl ), but are not allowed to set them (with setfacl ). | ||
hostdata=HostIDInfo | This field provides host (the computer on which the file system is being mounted) identity information to the lock module. The format and behavior of HostIDInfo depends on the lock module used. For lock_gulm , it overrides the uname -n network node name used as the default value by lock_gulm . This field is ignored by the lock_dlm and lock_nolock lock modules. | ||
| Forces GFS to treat the file system as a multihost file system. By default, using lock_nolock automatically turns on the localcaching and localflocks flags. | ||
| Tells GFS that it is running as a local file system. GFS can then turn on selected optimization capabilities that are not available when running in cluster mode. The localcaching flag is automatically turned on by lock_nolock . | ||
| Tells GFS to let the VFS (virtual file system) layer do all flock and fcntl. The localflocks flag is automatically turned on by lock_nolock . | ||
lockproto= | Allows the user to specify which locking protocol to use with the file system. If LockModuleName is not specified, the locking protocol name is read from the file-system superblock. | ||
locktable= | Allows the user to specify which locking table to use with the file system. | ||
oopses_ok |
| ||
upgrade | Upgrade the on-disk format of the file system so that it can be used by newer versions of GFS. |
4.3. Unmounting a File System
The GFS file system can be unmounted the same way as any Linux file system — by using the
umount
command.
Note
The
umount
command is a Linux system command. Information about this command can be found in the Linux umount
command man pages.
Usage
umount MountPoint
MountPoint
- Specifies the directory where the GFS file system should be mounted.
4.4. GFS Quota Management
File-system quotas are used to limit the amount of file-system space a user or group can use. A user or group does not have a quota limit until one is set. GFS keeps track of the space used by each user and group even when there are no limits in place. GFS updates quota information in a transactional way so system crashes do not require quota usages to be reconstructed.
To prevent a performance slowdown, a GFS node synchronizes updates to the quota file only periodically. The "fuzzy" quota accounting can allow users or groups to slightly exceed the set limit. To minimize this, GFS dynamically reduces the synchronization period as a "hard" quota limit is approached.
GFS uses its
gfs_quota
command to manage quotas. Other Linux quota facilities cannot be used with GFS.
4.4.1. Setting Quotas
Two quota settings are available for each user ID (UID) or group ID (GID): a hard limit and a warn limit.
A hard limit is the amount of space that can be used. The file system will not let the user or group use more than that amount of disk space. A hard limit value of zero means that no limit is enforced.
A warn limit is usually a value less than the hard limit. The file system will notify the user or group when the warn limit is reached to warn them of the amount of space they are using. A warn limit value of zero means that no limit is enforced.
Limits are set using the
gfs_quota
command. The command only needs to be run on a single node where GFS is mounted.
Usage
Setting Quotas, Hard Limit
gfs_quota limit -uUser
-lSize
-fMountPoint
gfs_quota limit -gGroup
-lSize
-fMountPoint
Setting Quotas, Warn Limit
gfs_quota warn -uUser
-lSize
-fMountPoint
gfs_quota warn -gGroup
-lSize
-fMountPoint
User
- A user ID to limit or warn. It can be either a user name from the password file or the UID number.
Group
- A group ID to limit or warn. It can be either a group name from the group file or the GID number.
Size
- Specifies the new value to limit or warn. By default, the value is in units of megabytes. The additional
-k
,-s
and-b
flags change the units to kilobytes, sectors, and file-system blocks, respectively. MountPoint
- Specifies the GFS file system to which the actions apply.
Examples
This example sets the hard limit for user Bert to 1024 megabytes (1 gigabyte) on file system
/gfs
.
gfs_quota limit -u Bert -l 1024 -f /gfs
This example sets the warn limit for group ID 21 to 50 kilobytes on file system
/gfs
.
gfs_quota warn -g 21 -l 50 -k -f /gfs
4.4.2. Displaying Quota Limits and Usage
Quota limits and current usage can be displayed for a specific user or group using the
gfs_quota get
command. The entire contents of the quota file can also be displayed using the gfs_quota list
command, in which case all IDs with a non-zero hard limit, warn limit, or value are listed.
Usage
Displaying Quota Limits for a User
gfs_quota get -uUser
-fMountPoint
Displaying Quota Limits for a Group
gfs_quota get -gGroup
-fMountPoint
Displaying Entire Quota File
gfs_quota list -f MountPoint
User
- A user ID to display information about a specific user. It can be either a user name from the password file or the UID number.
Group
- A group ID to display information about a specific group. It can be either a group name from the group file or the GID number.
MountPoint
- Specifies the GFS file system to which the actions apply.
Command Output
GFS quota information from the
gfs_quota
command is displayed as follows:
userUser
: limit:LimitSize
warn:WarnSize
value:Value
groupGroup
: limit:LimitSize
warn:WarnSize
value:Value
The
LimitSize
, WarnSize
, and Value
numbers (values) are in units of megabytes by default. Adding the -k
, -s
, or -b
flags to the command line change the units to kilobytes, sectors, or file-system blocks, respectively.
User
- A user name or ID to which the data is associated.
Group
- A group name or ID to which the data is associated.
LimitSize
- The hard limit set for the user or group. This value is zero if no limit has been set.
Value
- The actual amount of disk space used by the user or group.
Comments
When displaying quota information, the
gfs_quota
command does not resolve UIDs and GIDs into names if the -n
option is added to the command line.
Space allocated to GFS's hidden files can be left out of displayed values for the root UID and GID by adding the
-d
option to the command line. This is useful when trying to match the numbers from gfs_quota
with the results of a du
command.
Examples
This example displays quota information for all users and groups that have a limit set or are using any disk space on file system
/gfs
.
gfs_quota list -f /gfs
This example displays quota information in sectors for group
users
on file system /gfs
.
gfs_quota get -g users -f /gfs -s
4.4.3. Synchronizing Quotas
GFS stores all quota information in its own internal file on disk. A GFS node does not update this quota file for every file-system write; rather, it updates the quota file once every 60 seconds. This is necessary to avoid contention among nodes writing to the quota file, which would cause a slowdown in performance.
As a user or group approaches their quota limit, GFS dynamically reduces the time between its quota-file updates to prevent the limit from being exceeded. The normal time period between quota synchronizations is a tunable parameter,
quota_quantum
, and can be changed using the gfs_tool
command. By default, the time period is 60 seconds. Also, the quota_quantum
parameter must be set on each node and each time the file system is mounted. (Changes to the quota_quantum
parameter are not persistent across unmounts.)
You can use the
gfs_quota sync
command to synchronize the quota information from a node to the on-disk quota file between the automatic updates performed by GFS.
Usage
Synchronizing Quota Information
gfs_quota sync -f MountPoint
MountPoint
- Specifies the GFS file system to which the actions apply.
Tuning the Time Between Synchronizations
gfs_tool settuneMountPoint
quota_quantumSeconds
MountPoint
- Specifies the GFS file system to which the actions apply.
Seconds
- Specifies the new time period between regular quota-file synchronizations by GFS. Smaller values may increase contention and slow down performance.
Examples
This example synchronizes the quota information from the node it is run on to file system
/gfs
.
gfs_quota sync -f /gfs
This example changes the default time period between regular quota-file updates to one hour (3600 seconds) for file system
/gfs
on a single node.
gfs_tool settune /gfs quota_quantum 3600
4.4.4. Disabling/Enabling Quota Enforcement
Enforcement of quotas can be disabled for a file system without clearing the limits set for all users and groups. Enforcement can also be enabled. Disabling and enabling of quota enforcement is done by changing a tunable parameter,
quota_enforce
, with the gfs_tool
command. The quota_enforce
parameter must be disabled or enabled on each node where quota enforcement should be disabled/enabled. Each time the file system is mounted, enforcement is enabled by default. (Disabling is not persistent across unmounts.)
Usage
gfs_tool settune MountPoint
quota_enforce {0|1}
MountPoint
- Specifies the GFS file system to which the actions apply.
quota_enforce {0|1}
- 0 = disabled1 = enabled
Comments
A value of 0 disables enforcement. Enforcement can be enabled by running the command with a value of 1 (instead of 0) as the final command line parameter. Even when GFS is not enforcing quotas, it still keeps track of the file-system usage for all users and groups so that quota-usage information does not require rebuilding after re-enabling quotas.
Examples
This example disables quota enforcement on file system
/gfs
.
gfs_tool settune /gfs quota_enforce 0
This example enables quota enforcement on file system
/gfs
.
gfs_tool settune /gfs quota_enforce 1
4.4.5. Disabling/Enabling Quota Accounting
By default, quota accounting is enabled; therefore, GFS keeps track of disk usage for every user and group even when no quota limits have been set. Quota accounting incurs unnecessary overhead if quotas are not used. You can disable quota accounting completely by setting the
quota_account
tunable parameter to 0. This must be done on each node and after each mount. (The 0 setting is not persistent across unmounts.) Quota accounting can be enabled by setting the quota_account
tunable parameter to 1.
Usage
fs_tool settune MountPoint
quota_account {0|1}
MountPoint
- Specifies the GFS file system to which the actions apply.
quota_account {0|1}
- 0 = disabled1 = enabled
Comments
To enable quota accounting on a file system, the
quota_account
parameter must be set back to 1. Afterward, the GFS quota file must be initialized to account for all current disk usage for users and groups on the file system. The quota file is initialized by running: gfs_quota init -f MountPoint
.
Note
Initializing the quota file requires scanning the entire file system and may take a long time.
Examples
This example disables quota accounting on file system
/gfs
on a single node.
gfs_tool settune /gfs quota_account 0
This example enables quota accounting on file system
/gfs
on a single node and initializes the quota file.
#gfs_tool settune /gfs quota_account 1
#gfs_quota init -f /gfs
4.5. Growing a File System
The
gfs_grow
command is used to expand a GFS file system after the device where the file system resides has been expanded. Running a gfs_grow
command on an existing GFS file system fills all spare space between the current end of the file system and the end of the device with a newly initialized GFS file-system extension. When the fill operation is completed, the resource index for the file system is updated. All nodes in the cluster can then use the extra storage space that has been added.
The
gfs_grow
command must be run on a mounted file system, but only needs to be run on one node in a cluster. All the other nodes sense that the expansion has occurred and automatically start using the new space.
To verify that the changes were successful, use the
gfs_grow
command with the -T
(test) and -v
(verbose) flags. Running the command with those flags displays the current state of the mounted GFS file system.
Usage
gfs_grow MountPoint
MountPoint
- Specifies the GFS file system to which the actions apply.
Comments
Before running the
gfs_grow
command:
- Back up important data on the file system.
- Display the volume that is used by the file system to be expanded by running a
gfs_tool df
command.MountPoint
- Expand the underlying cluster volume with LVM. For information on administering LVM volumes, see the LVM Administrator's Guide
After running the
gfs_grow
command, run a df
command to check that the new space is now available in the file system.
Examples
In this example, the file system on the
/gfs1
directory is expanded.
gfs_grow /gfs1
In this example, the state of the mounted file system is checked.
gfs_grow -Tv /gfs1
Complete Usage
gfs_grow [Options
] {MountPoint
|Device
} [MountPoint
|Device
]
MountPoint
- Specifies the directory where the GFS file system is mounted.
Device
- Specifies the device node of the file system.
Table 4.3, “GFS-specific Options Available While Expanding A File System” describes the GFS-specific options that can be used while expanding a GFS file system.
Option | Description |
---|---|
-h | Help. Displays a short usage message. |
-q | Quiet. Turns down the verbosity level. |
-T | Test. Do all calculations, but do not write any data to the disk and do not expand the file system. |
-V | Displays command version information. |
-v | Turns up the verbosity of messages. |
4.6. Adding Journals to a File System
The
gfs_jadd
command is used to add journals to a GFS file system after the device where the file system resides has been expanded. Running a gfs_jadd
command on a GFS file system uses space between the current end of the file system and the end of the device where the file system resides. When the fill operation is completed, the journal index is updated.
The
gfs_jadd
command must be run on mounted file system, but it only needs to be run on one node in the cluster. All the other nodes sense that the expansion has occurred.
To verify that the changes were successful, use the
gfs_jadd
command with the -T
(test) and -v
(verbose) flags. Running the command with those flags displays the current state of the mounted GFS file system.
Usage
gfs_jadd -j Number MountPoint
Number
- Specifies the number of new journals to be added.
MountPoint
- Specifies the directory where the GFS file system is mounted.
Comments
Before running the
gfs_jadd
command:
- Back up important data on the file system.
- Run a
gfs_tool df
command to display the volume used by the file system where journals will be added.MountPoint
- Expand the underlying cluster volume with LVM. For information on administering LVM volumes, see the LVM Administrator's Guide
After running the
gfs_jadd
command, run a gfs_jadd
command with the -T
and -v
flags enabled to check that the new journals have been added to the file system.
Examples
In this example, one journal is added to the file system on the
/gfs1
directory.
gfs_jadd -j1 /gfs1
In this example, two journals are added to the file system on the
/gfs1
directory.
gfs_jadd -j2 /gfs1
In this example, the current state of the file system on the
/gfs1
directory is checked for the new journals.
gfs_jadd -Tv /gfs1
Complete Usage
gfs_jadd [Options
] {MountPoint
|Device
} [MountPoint
|Device
]
MountPoint
- Specifies the directory where the GFS file system is mounted.
Device
- Specifies the device node of the file system.
Table 4.4, “GFS-specific Options Available When Adding Journals” describes the GFS-specific options that can be used when adding journals to a GFS file system.
Flag | Parameter | Description |
---|---|---|
-h | Help. Displays short usage message. | |
-J | MegaBytes | Specifies the size of the new journals in megabytes. Default journal size is 128 megabytes. The minimum size is 32 megabytes. To add journals of different sizes to the file system, the gfs_jadd command must be run for each size journal. The size specified is rounded down so that it is a multiple of the journal-segment size that was specified when the file system was created. |
-j | Number | Specifies the number of new journals to be added by the gfs_jadd command. The default value is 1. |
-T | Test. Do all calculations, but do not write any data to the disk and do not add journals to the file system. Enabling this flag helps discover what the gfs_jadd command would have done if it were run without this flag. Using the -v flag with the -T flag turns up the verbosity level to display more information. | |
-q | Quiet. Turns down the verbosity level. | |
-V | Displays command version information. | |
-v | Turns up the verbosity of messages. |
4.7. Direct I/O
Direct I/O is a feature of the file system whereby file reads and writes go directly from the applications to the storage device, bypassing the operating system read and write caches. Direct I/O is used only by applications (such as databases) that manage their own caches.
An application invokes direct I/O by opening a file with the
O_DIRECT
flag. Alternatively, GFS can attach a direct I/O attribute to a file, in which case direct I/O is used regardless of how the file is opened.
When a file is opened with
O_DIRECT
, or when a GFS direct I/O attribute is attached to a file, all I/O operations must be done in block-size multiples of 512 bytes. The memory being read from or written to must also be 512-byte aligned.
One of the following methods can be used to enable direct I/O on a file:
O_DIRECT
- GFS file attribute
- GFS directory attribute
4.7.1. O_DIRECT
If an application uses the
O_DIRECT
flag on an open()
system call, direct I/O is used for the opened file.
To cause the
O_DIRECT
flag to be defined with recent glibc libraries, define _GNU_SOURCE
at the beginning of a source file before any includes, or define it on the cc line when compiling.
4.7.2. GFS File Attribute
The
gfs_tool
command can be used to assign (set) a direct I/O attribute flag, directio
, to a GFS file. The directio
flag can also be cleared.
Usage
Setting the
directio
Flag
gfs_tool setflag directio File
Clearing the
directio
Flag
gfs_tool clearflag directio File
File
- Specifies the file where the
directio
flag is assigned.
Example
In this example, the command sets the
directio
flag on the file named datafile
in directory /gfs1
.
gfs_tool setflag directio /gfs1/datafile
4.7.3. GFS Directory Attribute
The
gfs_tool
command can be used to assign (set) a direct I/O attribute flag, inherit_directio
, to a GFS directory. Enabling the inherit_directio
flag on a directory causes all newly created regular files in that directory to automatically inherit the directio
flag. Also, the inherit_directio
flag is inherited by any new subdirectories created in the directory. The inherit_directio
flag can also be cleared.
Usage
Setting the
inherit_directio
flag
gfs_tool setflag inherit_directio Directory
Clearing the
inherit_directio
flag
gfs_tool clearflag inherit_directio Directory
Directory
- Specifies the directory where the
inherit_directio
flag is set.
Example
In this example, the command sets the
inherit_directio
flag on the directory named /gfs1/data/
.
gfs_tool setflag inherit_directio /gfs1/data/
4.8. Data Journaling
Ordinarily, GFS writes only metadata to its journal. File contents are subsequently written to disk by the kernel's periodic sync that flushes file-system buffers. An
fsync()
call on a file causes the file's data to be written to disk immediately. The call returns when the disk reports that all data is safely written.
Data journaling can result in a reduced
fsync()
time, especially for small files, because the file data is written to the journal in addition to the metadata. An fsync()
returns as soon as the data is written to the journal, which can be substantially faster than the time it takes to write the file data to the main file system.
Applications that rely on
fsync()
to sync file data may see improved performance by using data journaling. Data journaling can be enabled automatically for any GFS files created in a flagged directory (and all its subdirectories). Existing files with zero length can also have data journaling turned on or off.
Using the
gfs_tool
command, data journaling is enabled on a directory (and all its subdirectories) or on a zero-length file by setting the inherit_jdata
or jdata
attribute flags to the directory or file, respectively. The directory and file attribute flags can also be cleared.
Usage
Setting and Clearing the
inherit_jdata
Flag
gfs_tool setflag inherit_jdataDirectory
gfs_tool clearflag inherit_jdataDirectory
Setting and Clearing the
jdata
Flag
gfs_tool setflag jdataFile
gfs_tool clearflag jdataFile
Directory
- Specifies the directory where the flag is set or cleared.
File
- Specifies the zero-length file where the flag is set or cleared.
Examples
This example shows setting the
inherit_jdata
flag on a directory. All files created in the directory or any of its subdirectories will have the jdata
flag assigned automatically. Any data written to the files will be journaled.
gfs_tool setflag inherit_jdata /gfs1/data/
This example shows setting the
jdata
flag on a file. The file must be zero size. Any data written to the file will be journaled.
gfs_tool setflag jdata /gfs1/datafile
4.9. Configuring atime
Updates
Each file inode and directory inode has three time stamps associated with it:
ctime
— The last time the inode status was changedmtime
— The last time the file (or directory) data was modifiedatime
— The last time the file (or directory) data was accessed
If
atime
updates are enabled as they are by default on GFS and other Linux file systems then every time a file is read, its inode needs to be updated.
Because few applications use the information provided by
atime
, those updates can require a significant amount of unnecessary write traffic and file-locking traffic. That traffic can degrade performance; therefore, it may be preferable to turn off atime
updates.
Two methods of reducing the effects of
atime
updating are available:
- Mount with
noatime
- Tune GFS
atime
quantum
4.9.1. Mount with noatime
A standard Linux mount option,
noatime
, can be specified when the file system is mounted, which disables atime
updates on that file system.
Usage
mount -t gfs BlockDevice MountPoint
-o noatime
BlockDevice
- Specifies the block device where the GFS file system resides.
MountPoint
- Specifies the directory where the GFS file system should be mounted.
Example
In this example, the GFS file system resides on the
/dev/vg01/lvol0
and is mounted on directory /gfs1
with atime updates turned off.
mount -t gfs /dev/vg01/lvol0 /gfs1 -o noatime
4.9.2. Tune GFS atime
Quantum
When
atime
updates are enabled, GFS (by default) only updates them once an hour. The time quantum is a tunable parameter that can be adjusted using the gfs_tool
command.
Each GFS node updates the access time based on the difference between its system time and the time recorded in the inode. It is required that system clocks of all GFS nodes in a cluster be synchronized. If a node's system time is out of synchronization by a significant fraction of the tunable parameter,
atime_quantum
, then atime
updates are written more frequently. Increasing the frequency of atime
updates may cause performance degradation in clusters with heavy work loads.
By using the
gettune
flag of the gfs_tool
command, all current tunable parameters including atime_quantum
(default is 3600 seconds) are displayed.
The
gfs_tool settune
command is used to change the atime_quantum
parameter value. It must be set on each node and each time the file system is mounted. (The setting is not persistent across unmounts.)
Usage
Displaying Tunable Parameters
gfs_tool gettune MountPoint
MountPoint
- Specifies the directory where the GFS file system is mounted.
Changing the
atime_quantum
Parameter Value
gfs_tool settuneMountPoint
atime_quantumSeconds
MountPoint
- Specifies the directory where the GFS file system is mounted.
Seconds
- Specifies the update period in seconds.
Examples
In this example, all GFS tunable parameters for the file system on the mount point
/gfs1
are displayed.
gfs_tool gettune /gfs1
In this example, the
atime
update period is set to once a day (86,400 seconds) for the GFS file system on mount point /gfs1
.
gfs_tool settune /gfs1 atime_quantum 86400
4.10. Suspending Activity on a File System
You can suspend write activity to a file system by using the
gfs_tool freeze
command. Suspending write activity allows hardware-based device snapshots to be used to capture the file system in a consistent state. The gfs_tool unfreeze
command ends the suspension.
Usage
Start Suspension
gfs_tool freeze MountPoint
End Suspension
gfs_tool unfreeze MountPoint
MountPoint
- Specifies the file system.
Examples
This example suspends writes to file system
/gfs
.
gfs_tool freeze /gfs
This example ends suspension of writes to file system
/gfs
.
gfs_tool unfreeze /gfs
4.11. Displaying Extended GFS Information and Statistics
You can use the
gfs_tool
command to gather a variety of details about GFS. This section describes typical use of the gfs_tool
command for displaying statistics, space usage, and extended status.
Usage
Displaying Statistics
gfs_tool counters MountPoint
The
counters
flag displays statistics about a file system. If -c
is used, the gfs_tool
command continues to run, displaying statistics once per second.
Displaying Space Usage
gfs_tool df MountPoint
The
df
flag displays a space-usage summary of a given file system. The information is more detailed than a standard df
.
Displaying Extended Status
gfs_tool stat File
The
stat
flag displays extended status information about a file.
MountPoint
- Specifies the file system to which the action applies.
File
- Specifies the file from which to get information.
The
gfs_tool
command provides additional action flags (options) not listed in this section. For more information about other gfs_tool
flags, refer to the gfs_tool
man page.
Examples
This example reports extended file system usage about file system
/gfs
.
gfs_tool df /gfs
This example reports extended file status about file
/gfs/datafile
.
gfs_tool stat /gfs/datafile
4.12. Repairing a File System
When nodes fail with the file system mounted, file-system journaling allows fast recovery. However, if a storage device loses power or is physically disconnected, file-system corruption may occur. (Journaling cannot be used to recover from storage subsystem failures.) When that type of corruption occurs, you can recover the GFS file system by using the
gfs_fsck
command.
The
gfs_fsck
command must only be run on a file system that is unmounted from all nodes.
Note
The
gfs_fsck
command has changed from previous releases of Red Hat GFS in the following ways:
- You can no longer set the interactive mode with Ctrl+C. Pressing Ctrl+C now cancels the
gfs_fsck
command. Do not press Ctrl+C unless you want to cancel the command. - You can increase the level of verbosity by using the
-v
flag. Adding a second-v
flag increases the level again. - You can decrease the level of verbosity by using the
-q
flag. Adding a second-q
flag decreases the level again. - The
-n
option opens a file system as read-only and answersno
to any queries automatically. The option provides a way of trying the command to reveal errors without actually allowing thegfs_fsck
command to take effect.
Refer to the
gfs_fsck
man page, gfs_fsck(8)
, for additional information about other command options.
Usage
gfs_fsck -y BlockDevice
-y
- The
-y
flag causes all questions to be answered withyes
. With the-y
flag specified, thegfs_fsck
command does not prompt you for an answer before making changes. BlockDevice
- Specifies the block device where the GFS file system resides.
Example
In this example, the GFS file system residing on block device
/dev/vg01/lvol0
is repaired. All queries to repair are automatically answered with yes
.
gfs_fsck -y /dev/vg01/lvol0
4.13. Context-Dependent Path Names
Context-Dependent Path Names (CDPNs) allow symbolic links to be created that point to variable destination files or directories. The variables are resolved to real files or directories each time an application follows the link. The resolved value of the link depends on the node or user following the link.
CDPN variables can be used in any path name, not just with symbolic links. However, the CDPN variable name cannot be combined with other characters to form an actual directory or file name. The CDPN variable must be used alone as one segment of a complete path.
Usage
For a Normal Symbolic Link
ln -sTarget
LinkName
Target
- Specifies an existing file or directory on a file system.
LinkName
- Specifies a name to represent the real file or directory on the other end of the link.
For a Variable Symbolic Link
ln -sVariable
LinkName
Variable
- Specifies a special reserved name from a list of values (refer to Table 4.5, “CDPN
Variable
Values”) to represent one of multiple existing files or directories. This string is not the name of an actual file or directory itself. (The real files or directories must be created in a separate step using names that correlate with the type of variable used.) LinkName
- Specifies a name that will be seen and used by applications and will be followed to get to one of the multiple real files or directories. When
LinkName
is followed, the destination depends on the type of variable and the node or user doing the following.
Variable | Description |
---|---|
@hostname | This variable resolves to a real file or directory named with the hostname string produced by the output of the following command: echo `uname -n` |
@mach | This variable resolves to a real file or directory name with the machine-type string produced by the output of the following command: echo `uname -m` |
@os | This variable resolves to a real file or directory named with the operating-system name string produced by the output of the following command: echo `uname -s` |
@sys | This variable resolves to a real file or directory named with the combined machine type and OS release strings produced by the output of the following command: echo `uname -m`_`uname -s` |
@uid | This variable resolves to a real file or directory named with the user ID string produced by the output of the following command: echo `id -u` |
@gid | This variable resolves to a real file or directory named with the group ID string produced by the output of the following command: echo `id -g` |
Example
In this example, there are three nodes with hostnames
n01
, n02
and n03
. Applications on each node uses directory /gfs/log/
, but the administrator wants these directories to be separate for each node. To do this, no actual log directory is created; instead, an @hostname
CDPN link is created with the name log
. Individual directories /gfs/n01/
, /gfs/n02/
, and /gfs/n03/
are created that will be the actual directories used when each node references /gfs/log/
.
n01#cd /gfs
n01#mkdir n01 n02 n03
n01#ln -s @hostname log
n01#ls -l /gfs
lrwxrwxrwx 1 root root 9 Apr 25 14:04 log -> @hostname/ drwxr-xr-x 2 root root 3864 Apr 25 14:05 n01/ drwxr-xr-x 2 root root 3864 Apr 25 14:06 n02/ drwxr-xr-x 2 root root 3864 Apr 25 14:06 n03/ n01#touch /gfs/log/fileA
n02#touch /gfs/log/fileB
n03#touch /gfs/log/fileC
n01#ls /gfs/log/
fileA n02#ls /gfs/log/
fileB n03#ls /gfs/log/
fileC
Appendix A. Upgrading GFS
To upgrade a node to Red Hat GFS 6.1 from earlier versions of Red Hat GFS, you must convert the GFS cluster configuration archive (CCA) to a Red Hat Cluster Suite cluster configuration system (CCS) configuration file (
/etc/cluster/cluster.conf
) and convert GFS pool
volumes to LVM2 volumes.
This appendix contains instructions for upgrading from GFS 6.0 (or GFS 5.2.1) to Red Hat GFS 6.1, using GULM as the lock manager.
Note
You must retain GULM lock management for the upgrade to Red Hat GFS 6.1; that is, you cannot change from GULM lock management to DLM lock management during the upgrade to Red Hat GFS 6.1. However, after the upgrade to GFS 6.1, you can change lock managers.
The following procedure demonstrates upgrading to Red Hat GFS 6.1 from a GFS 6.0 (or GFS 5.2.1) configuration with an example
pool
configuration for a pool volume named argus
.
poolname argus subpools 1 subpool 0 512 1 gfs_data pooldevice 0 0 /dev/sda1
- Halt the GFS nodes and the lock server nodes as follows:
- Unmount GFS file systems from all nodes.
- Stop the lock servers; at each lock server node, stop the lock server as follows:
#
service lock_gulmd stop
- Stop
ccsd
at all nodes; at each node, stopccsd
as follows:#
service ccsd stop
- Deactivate pools; at each node, deactivate GFS
pool
volumes as follows:#
service pool stop
- Uninstall Red Hat GFS RPMs.
- Install new software:
- Install Red Hat Enterprise Linux version 4 software (or verify that it is installed).
- Install Red Hat Cluster Suite and Red Hat GFS RPMs.
- At all GFS 6.1 nodes, create a cluster configuration file directory (
/etc/cluster
) and upgrade the CCA (in this example, located in/dev/pool/cca
) to the new Red Hat Cluster Suite CCS configuration file format by running theccs_tool upgrade
command as shown in the following example:#
mkdir /etc/cluster
#ccs_tool upgrade /dev/pool/cca > /etc/cluster/cluster.conf
- At all GFS 6.1 nodes, start
ccsd
, run thelock_gulmd -c
command, and startclvmd
as shown in the following example:#
ccsd
#lock_gulmd -c
Warning! You didn't specify a cluster name before --use_ccs Letting ccsd choose which cluster we belong to. #clvmd
Note
Ignore the warning message following thelock_gulmd -c
command. Because the cluster name is already included in the converted configuration file, there is no need to specify a cluster name when issuing thelock_gulmd -c
command. - At all GFS 6.1 nodes, run
vgscan
as shown in the following example:#
vgscan
Reading all physical volumes. This may take a while... Found volume group "argus" using metadata type pool - At one GFS 6.1 node, convert the
pool
volume to an LVM2 volume by running thevgconvert
command as shown in the following example:#
vgconvert -M2 argus
Volume group argus successfully converted - At all GFS 6.1 nodes, run
vgchange -ay
as shown in the following example:#
vgchange -ay
1 logical volume(s) in volume group "argus" now active - At the first node to mount a GFS file system, run the
mount
command with theupgrade
option as shown in the following example:#
mount -t gfs -o upgrade /dev/pool/argus /mnt/gfs1
Note
This step only needs to be done once — on the first mount of the GFS file system.Note
If static minor numbers were used onpool
volumes and the GFS 6.1 nodes are using LVM2 for other purposes (root file system) there may be problems activating thepool
volumes under GFS 6.1. That is because of static minor conflicts. Refer to the following Bugzilla report for more information:https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=146035
Appendix B. Revision History
Revision History | ||||
---|---|---|---|---|
Revision 1.1-7.400 | 2013-10-31 | |||
| ||||
Revision 1.1-7 | 2012-07-18 | |||
| ||||
Revision 1.1-0 | Wed Mar 17 2010 | |||
| ||||
Revision 1.0-0 | Wed Apr 01 2009 | |||
|
Index
A
- adding journals to a file system, Adding Journals to a File System
- atime, configuring updates, Configuring atime Updates
- mounting with noatime, Mount with noatime
- tuning atime quantum, Tune GFS atime Quantum
- audience, Audience
C
- CDPN variable values table, Usage
- configuration, before, Before Setting Up GFS
- configuration, initial, Getting Started
- prerequisite tasks, Prerequisite Tasks
- console access
- system requirements, Console Access
D
- data journaling, Data Journaling
- direct I/O, Direct I/O
- directory attribute, GFS Directory Attribute
- file attribute, GFS File Attribute
- O_DIRECT, O_DIRECT
- displaying extended GFS information and statistics, Displaying Extended GFS Information and Statistics
F
- feedback, Feedback
- fencing
- system requirements, Fencing
- fibre channel network requirements table, Fibre Channel Storage Network
- fibre channel storage device requirements table, Fibre Channel Storage Devices
- fibre channel storage devices
- system requirements, Fibre Channel Storage Devices
- fibre channel storage network
- system requirements, Fibre Channel Storage Network
- file system
- adding journals, Adding Journals to a File System
- atime, configuring updates, Configuring atime Updates
- mounting with noatime, Mount with noatime
- tuning atime quantum, Tune GFS atime Quantum
- context-dependent path names (CDPNs), Context-Dependent Path Names
- data journaling, Data Journaling
- direct I/O, Direct I/O
- directory attribute, GFS Directory Attribute
- file attribute, GFS File Attribute
- O_DIRECT, O_DIRECT
- growing, Growing a File System
- making, Making a File System
- mounting, Mounting a File System
- quota management, GFS Quota Management
- disabling/enabling quota accounting, Disabling/Enabling Quota Accounting
- disabling/enabling quota enforcement, Disabling/Enabling Quota Enforcement
- displaying quota limits, Displaying Quota Limits and Usage
- setting quotas, Setting Quotas
- synchronizing quotas, Synchronizing Quotas
- repairing, Repairing a File System
- suspending activity, Suspending Activity on a File System
- unmounting, Unmounting a File System
G
- GFS
- atime, configuring updates, Configuring atime Updates
- mounting with noatime, Mount with noatime
- tuning atime quantum, Tune GFS atime Quantum
- direct I/O, Direct I/O
- directory attribute, GFS Directory Attribute
- file attribute, GFS File Attribute
- O_DIRECT, O_DIRECT
- displaying extended information and statistics, Displaying Extended GFS Information and Statistics
- managing, Managing GFS
- quota management, GFS Quota Management
- disabling/enabling quota accounting, Disabling/Enabling Quota Accounting
- disabling/enabling quota enforcement, Disabling/Enabling Quota Enforcement
- displaying quota limits, Displaying Quota Limits and Usage
- setting quotas, Setting Quotas
- synchronizing quotas, Synchronizing Quotas
- GFS functions, GFS Functions
- GFS software subsystem components table, GFS Software Subsystems
- GFS software subsystems, GFS Software Subsystems
- GFS-specific options for adding journals table, Complete Usage
- GFS-specific options for expanding file systems table, Complete Usage
- gfs_mkfs command options table, Complete Options
- growing a file system, Growing a File System
I
- initial tasks
- setup, initial, Initial Setup Tasks
- introduction, Introduction
- audience, Audience
- references, Recommended References
M
- making a file system, Making a File System
- managing GFS, Managing GFS
- mount table, Complete Usage
- mounting a file system, Mounting a File System
N
- network power switches
- system requirements, Network Power Switches
O
- overview, GFS Overview
- configuration, before, Before Setting Up GFS
- economy, Performance, Scalability, and Economy
- GFS functions, GFS Functions
- GFS software subsystems, GFS Software Subsystems
- performance, Performance, Scalability, and Economy
- scalability, Performance, Scalability, and Economy
P
- path names, context-dependent (CDPNs), Context-Dependent Path Names
- platform
- system requirements, Platform Requirements
- platform requirements table, Platform Requirements
- preface (see introduction)
- prerequisite tasks
- configuration, initial, Prerequisite Tasks
Q
- quota management, GFS Quota Management
- disabling/enabling quota accounting, Disabling/Enabling Quota Accounting
- disabling/enabling quota enforcement, Disabling/Enabling Quota Enforcement
- displaying quota limits, Displaying Quota Limits and Usage
- setting quotas, Setting Quotas
- synchronizing quotas, Synchronizing Quotas
R
- recommended references table, Recommended References
- Red Hat Cluster Suite
- system requirements, Red Hat Cluster Suite
- references, recommended, Recommended References
- repairing a file system, Repairing a File System
S
- setup, initial
- initial tasks, Initial Setup Tasks
- suspending activity on a file system, Suspending Activity on a File System
- system requirements, System Requirements
- console access, Console Access
- fencing, Fencing
- fibre channel storage devices, Fibre Channel Storage Devices
- fibre channel storage network, Fibre Channel Storage Network
- network power switches, Network Power Switches
- platform, Platform Requirements
- Red Hat Cluster Suite, Red Hat Cluster Suite
T
- tables
- CDPN variable values, Usage
- fibre channel network requirements, Fibre Channel Storage Network
- fibre channel storage device requirements, Fibre Channel Storage Devices
- GFS software subsystem components, GFS Software Subsystems
- GFS-specific options for adding journals, Complete Usage
- GFS-specific options for expanding file systems, Complete Usage
- gfs_mkfs command options, Complete Options
- mount options, Complete Usage
- platform requirements, Platform Requirements
- recommended references, Recommended References
U
- unmounting a file system, Unmounting a File System
Legal Notice
Copyright © 2009 Red Hat, Inc.
This document is licensed by Red Hat under the Creative Commons Attribution-ShareAlike 3.0 Unported License. If you distribute this document, or a modified version of it, you must provide attribution to Red Hat, Inc. and provide a link to the original. If the document is modified, all Red Hat trademarks must be removed.
Red Hat, as the licensor of this document, waives the right to enforce, and agrees not to assert, Section 4d of CC-BY-SA to the fullest extent permitted by applicable law.
Red Hat, Red Hat Enterprise Linux, the Shadowman logo, the Red Hat logo, JBoss, OpenShift, Fedora, the Infinity logo, and RHCE are trademarks of Red Hat, Inc., registered in the United States and other countries.
Linux® is the registered trademark of Linus Torvalds in the United States and other countries.
Java® is a registered trademark of Oracle and/or its affiliates.
XFS® is a trademark of Silicon Graphics International Corp. or its subsidiaries in the United States and/or other countries.
MySQL® is a registered trademark of MySQL AB in the United States, the European Union and other countries.
Node.js® is an official trademark of Joyent. Red Hat is not formally related to or endorsed by the official Joyent Node.js open source or commercial project.
The OpenStack® Word Mark and OpenStack logo are either registered trademarks/service marks or trademarks/service marks of the OpenStack Foundation, in the United States and other countries and are used with the OpenStack Foundation's permission. We are not affiliated with, endorsed or sponsored by the OpenStack Foundation, or the OpenStack community.
All other trademarks are the property of their respective owners.