第8章 Open vSwitch を使用した LACP ボンディングの設定とテスト

S4048-ON-sw#config t
S4048-ON-sw(conf)#default int te1/2
S4048-ON-sw(conf)#default int te1/7

S4048-ON-sw(conf)#int range te1/2,te1/7
S4048-ON-sw(conf-if-range-te-1/2,te-1/7)#port-channel-protocol lacp
S4048-ON-sw(conf-if-range-te-1/2,te-1/7-lacp)#
S4048-ON-sw(conf-if-range-te-1/2,te-1/7-lacp)#port-channel 1 mode active
S4048-ON-sw(conf-if-range-te-1/2,te-1/7-lacp)#end
S4048-ON-sw#config t
S4048-ON-sw(conf)#int range te1/2,te1/7
S4048-ON-sw(conf-if-range-te-1/2,te-1/7)# no ip address
S4048-ON-sw(conf-if-range-te-1/2,te-1/7)# mtu 9216
S4048-ON-sw(conf-if-range-te-1/2,te-1/7)# flowcontrol rx on tx off
S4048-ON-sw(conf-if-range-te-1/2,te-1/7)# no shutdown
S4048-ON-sw(conf-if-range-te-1/2,te-1/7)#end
S4048-ON-sw#show run int te1/2
!
interface TenGigabitEthernet 1/2
 no ip address
 mtu 9216
 flowcontrol rx on tx off
!
 port-channel-protocol LACP
  port-channel 1 mode active
 no shutdown

S4048-ON-sw#config t
S4048-ON-sw(conf)#int range vlan901-909
S4048-ON-sw(conf-if-range-vl-901-909)#tagged Port-channel 1
S4048-ON-sw(conf-if-range-vl-901-909)#end
S4048-ON-sw#

S4048-ON-sw#show vlan id 902

Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated
       O - Openflow, Vx - Vxlan
Q: U - Untagged, T - Tagged
   x - Dot1x untagged, X - Dot1x tagged
   o - OpenFlow untagged, O - OpenFlow tagged
   G - GVRP tagged, M - Vlan-stack
   i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged

    NUM    Status    Description                     Q Ports
    902    Active    Tenant                          T Po1()
                                                     T Te 1/1,1/3-1/6,1/8-1/20

S4048-ON-sw#show lacp 1
Port-channel 1 admin up, oper down, mode lacp
LACP Fast Switch-Over Disabled
Actor   System ID:  Priority 32768, Address 1418.7789.9a8a
Partner System ID:  Priority 0, Address 0000.0000.0000
Actor Admin Key 1, Oper Key 1, Partner Oper Key 1, VLT Peer Oper Key 1
LACP LAG 1 is an individual link

LACP LAG 1 is a normal LAG

A - Active LACP, B - Passive LACP, C - Short Timeout, D - Long Timeout
E - Aggregatable Link, F - Individual Link, G - IN_SYNC, H - OUT_OF_SYNC
I - Collection enabled, J - Collection disabled, K - Distribution enabled
L - Distribution disabled, M - Partner Defaulted, N - Partner Non-defaulted,
O - Receiver is in expired state, P - Receiver is not in expired state

Port Te 1/2 is disabled, LACP is disabled and mode is lacp
Port State: Not in Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEHJLMP Key 1 Priority 32768
  Partner is not present

Port Te 1/7 is enabled, LACP is enabled and mode is lacp
Port State: Not in Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEHJLMP Key 1 Priority 32768
  Partner is not present