이 콘텐츠는 선택한 언어로 제공되지 않습니다.

1.9. Changing the LDAP and LDAPS Port Numbers


By default, Directory Server uses port 389 for the LDAP and, if enabled, port 636 for the LDAPS protocol. You can change these port numbers, for example, to run multiple Directory Server instances on one host.

Important

The new ports you assign to the protocols for an instance must not be in use by any other service.

1.9.1. Changing the Port Numbers Using the Command Line

To change the port numbers using the command line, update the following parameters:
  • nsslapd-port: Stores the port number the instance uses for the LDAP protocol.
  • nsslapd-secureport: Stores the port number the instance uses for the LDAPS protocol.
To change the port numbers of the LDAP and LDAPS protocol using the command line:
  1. Optionally, display the currently configured port numbers for the instance:
    # dsconf -D "cn=Directory Manager" ldap://server.example.com config get nsslapd-port nsslapd-secureport
    nsslapd-port: 389
    nsslapd-secureport: 636
  2. To change the LDAP port:
    1. Set the port for the LDAP protocol. For example, to set it to 1389:
      # dsconf -D "cn=Directory Manager" ldap://server.example.com config replace nsslapd-port=1389
      Successfully replaced "nsslapd-port"
    2. Set the ldap_port_t type for the LDAP port you assigned in the previous step:
      # semanage port -a -t ldap_port_t -p tcp 1389
  3. To change the LDAPS port:
    1. Set the port for the LDAPS protocol. For example, to set it to 1636:
      # dsconf -D "cn=Directory Manager" ldap://server.example.com config replace nsslapd-secureport=1636
      Successfully replaced "nsslapd-secureport"
    2. Set the ldap_port_t type for the LDAPS port you assigned in the previous step:
      # semanage port -a -t ldap_port_t -p tcp 1636
  4. Restart the instance:
    # dsctl instance_name restart

1.9.2. Changing the Port Numbers Using the Web Console

To change the port numbers of the LDAP and LDAPS protocol using the web console:
  1. Open the Directory Server user interface in the web console. See Section 1.4, “Logging Into Directory Server Using the Web Console”.
  2. Select the instance.
  3. To change the LDAP port:
    1. Open the Server Settings menu.
    2. On the Server Settings tab, fill the new port number into the LDAP Port field.
    3. Click Save.
  4. To change the LDAPS port:
    1. Open the Server Settings menu.
    2. On the General Settings tab, fill the new port number into the LDAPS Port field.
    3. Click Save.
Red Hat logoGithubRedditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 문서 정보

Legal Notice

Theme

© 2026 Red Hat
맨 위로 이동