Red Hat Summit이 콘텐츠는 선택한 언어로 제공되지 않습니다.
Chapter 1. Online Storage Reconfiguration
1.1. Fibre Channel
링크 복사링크가 클립보드에 복사되었습니다!
This section discusses the Fibre Channel API, native Red Hat Enterprise Linux 5 Fibre Channel drivers, and the Fibre Channel capabilities of these drivers.
1.1.1. Fibre Channel API
링크 복사링크가 클립보드에 복사되었습니다!
Below is a list of
/sys/class/ directories that contain files used to provide the userspace API. In each item, host numbers are designated by H, bus numbers are B, targets are T, logical unit numbers (LUNs) are L, and remote port numbers are R.
Important
If your system is using multipath software, Red Hat recommends that you consult your hardware vendor before changing any of the values described in this section.
- Transport:
/sys/class/fc_transport/targetH:B:T/ port_id— 24-bit port ID/addressnode_name— 64-bit node nameport_name— 64-bit port name
- Remote Port:
/sys/class/fc_remote_ports/rport-H:B-R/ port_idnode_nameport_namedev_loss_tmo— number of seconds to wait before marking a link as "bad". Once a link is marked bad, IO running on its corresponding path (along with any new IO on that path) will be failed.The defaultdev_loss_tmovalue varies, depending on which driver/device is used. If a Qlogic adapter is used, the default is 35 seconds, while if an Emulex adapter is used, it is 30 seconds. Thedev_loss_tmovalue can be changed via thescsi_transport_fcmodule parameterdev_loss_tmo, although the driver can override this timeout value.The maximumdev_loss_tmovalue is 600 seconds. Ifdev_loss_tmois set to zero or any value greater than 600, the driver's internal timeouts will be used instead.fast_io_fail_tmo— length of time to wait before failing IO executed when a link problem is detected. IO that reaches the driver will fail. If IO is in a blocked queue, it will not be failed untildev_loss_tmoexpires and the queue is unblocked.
- Host:
/sys/class/fc_host/hostH/
1.1.2. Native Fibre Channel Drivers and Capabilities
링크 복사링크가 클립보드에 복사되었습니다!
Red Hat Enterprise Linux 5 ships with the following native fibre channel drivers:
lpfcqla2xxxzfcpmptfc
Table 1.1, “Fibre-Channel API Capabilities” describes the different fibre-channel API capabilities of each native Red Hat Enterprise Linux 5 driver. X denotes support for the capability.
lpfc | qla2xxx | zfcp | mptfc | |
|---|---|---|---|---|
Transport port_id | X | X | X | X |
Transport node_name | X | X | X | X |
Transport port_name | X | X | X | X |
Remote Port dev_loss_tmo | X | X | X | X |
Remote Port fast_io_fail_tmo | X | X [a] | ||
Host port_id | X | X | X | X |
Host issue_lip | X | X | ||
[a]
Supported as of Red Hat Enterprise Linux 5.4
| ||||
'%20d='M201.5%20305.5c-13.8%200-24.9-11.1-24.9-24.6%200-13.8%2011.1-24.9%2024.9-24.9%2013.6%200%2024.6%2011.1%2024.6%2024.9%200%2013.6-11.1%2024.6-24.6%2024.6zM504%20256c0%20137-111%20248-248%20248S8%20393%208%20256%20119%208%20256%208s248%20111%20248%20248zm-132.3-41.2c-9.4%200-17.7%203.9-23.8%2010-22.4-15.5-52.6-25.5-86.1-26.6l17.4-78.3%2055.4%2012.5c0%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.3%2024.9-24.9s-11.1-24.9-24.9-24.9c-9.7%200-18%205.8-22.1%2013.8l-61.2-13.6c-3-.8-6.1%201.4-6.9%204.4l-19.1%2086.4c-33.2%201.4-63.1%2011.3-85.5%2026.8-6.1-6.4-14.7-10.2-24.1-10.2-34.9%200-46.3%2046.9-14.4%2062.8-1.1%205-1.7%2010.2-1.7%2015.5%200%2052.6%2059.2%2095.2%20132%2095.2%2073.1%200%20132.3-42.6%20132.3-95.2%200-5.3-.6-10.8-1.9-15.8%2031.3-16%2019.8-62.5-14.9-62.5zM302.8%20331c-18.2%2018.2-76.1%2017.9-93.6%200-2.2-2.2-6.1-2.2-8.3%200-2.5%202.5-2.5%206.4%200%208.6%2022.8%2022.8%2087.3%2022.8%20110.2%200%202.5-2.2%202.5-6.1%200-8.6-2.2-2.2-6.1-2.2-8.3%200zm7.7-75c-13.6%200-24.6%2011.1-24.6%2024.9%200%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.1%2024.9-24.6%200-13.8-11-24.9-24.9-24.9z'/%3e%3c/svg%3e){kind=small}