Red Hat Summit Red Hat Summit지원콘솔개발자평가판 시작연락처

이 콘텐츠는 선택한 언어로 제공되지 않습니다.

B.3.4. Creating the Resources and Resource Groups with the pcs Command

This use case requires that you create four cluster resources. To ensure these resources all run on the same node, they are configured as part of the resource group apachegroup. The resources to create are as follows, listed in the order in which they will start.
  1. An LVM resource named my_lvm that uses the LVM volume group you created in Section B.3.1, “Configuring an LVM Volume with an ext4 File System”.
  2. A Filesystem resource named my_fs, that uses the filesystem device /dev/my_vg/my_lv you created in Section B.3.1, “Configuring an LVM Volume with an ext4 File System”.
  3. An IPaddr2 resource, which is a floating IP address for the apachegroup resource group. The IP address must not be one already associated with a physical node. If the IPaddr2 resource's NIC device is not specified, the floating IP must reside on the same network as the statically assigned IP addresses used by the cluster nodes, otherwise the NIC device to assign the floating IP address cannot be properly detected.
  4. An apache resource named Website that uses the index.html file and the Apache configuration you defined in Section B.3.2, “Web Server Configuration”.
The following procedure creates the resource group apachegroup and the resources that the group contains. The resources will start in the order in which you add them to the group, and they will stop in the reverse order in which they are added to the group. Run this procedure from one node of the cluster only.
  1. The following command creates the LVM resource my_lvm. This command specifies the exclusive=true parameter to ensure that only the cluster is capable of activating the LVM logical volume. Because the resource group apachegroup does not yet exist, this command creates the resource group. 
    [root@z1 ~]# pcs resource create my_lvm LVM volgrpname=my_vg \
exclusive=true --group apachegroup
    Copy to Clipboard Toggle word wrap
    When you create a resource, the resource is started automatically. You can use the following command to confirm that the resource was created and has started. 
    # pcs resource show
 Resource Group: apachegroup
     my_lvm	(ocf::heartbeat:LVM):	Started
    Copy to Clipboard Toggle word wrap
    You can manually stop and start an individual resource with the pcs resource disable and pcs resource enable commands.
  2. The following commands create the remaining resources for the configuration, adding them to the existing resource group apachegroup. 
    [root@z1 ~]# pcs resource create my_fs Filesystem \
device="/dev/my_vg/my_lv" directory="/var/www" fstype="ext4" --group \
apachegroup

[root@z1 ~]# pcs resource create VirtualIP IPaddr2 ip=198.51.100.3 \
cidr_netmask=24 --group apachegroup

[root@z1 ~]# pcs resource create Website apache \
configfile="/etc/httpd/conf/httpd.conf" \
statusurl="http://127.0.0.1/server-status" --group apachegroup
    Copy to Clipboard Toggle word wrap
  3. After creating the resources and the resource group that contains them, you can check the status of the cluster. Note that all four resources are running on the same node. 
    [root@z1 ~]# pcs status
Cluster name: my_cluster
Last updated: Wed Jul 31 16:38:51 2013
Last change: Wed Jul 31 16:42:14 2013 via crm_attribute on z1.example.com
Stack: corosync
Current DC: z2.example.com (2) - partition with quorum
Version: 1.1.10-5.el7-9abe687
2 Nodes configured
6 Resources configured


Online: [ z1.example.com z2.example.com ]

Full list of resources:
 myapc	(stonith:fence_apc_snmp):	Started z1.example.com 
 Resource Group: apachegroup
     my_lvm	(ocf::heartbeat:LVM):	Started z1.example.com 
     my_fs	(ocf::heartbeat:Filesystem):	Started z1.example.com 
     VirtualIP	(ocf::heartbeat:IPaddr2):	Started z1.example.com 
     Website	(ocf::heartbeat:apache):	Started z1.example.com
    Copy to Clipboard Toggle word wrap
    Note that if you have not configured a fencing device for your cluster, as described in Section B.2, “Fencing Configuration”, by default the resources do not start.
  4. Once the cluster is up and running, you can point a browser to the IP address you defined as the IPaddr2 resource to view the sample display, consisting of the simple word "Hello". 
    Hello
    Copy to Clipboard Toggle word wrap
    If you find that the resources you configured are not running, you can run the pcs resource debug-start resource command to test the resource configuration. For information on the pcs resource debug-start command, see the High Availability Add-On Reference manual.
Red Hat logoGithubredditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다. 최신 업데이트를 확인하세요.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

Theme

© 2026 Red Hat맨 위로 이동