B.3.5. Testing the Resource Configuration

In the cluster status display shown in Section B.3.4, “Creating the Resources and Resource Groups with the pcs Command”, all of the resources are running on node z1.example.com. You can test whether the resource group fails over to node z2.example.com by using the following procedure to put the first node in standby mode, after which the node will no longer be able to host resources.

The following command puts node z1.example.com in standby mode.
```
root@z1 ~]# pcs cluster standby z1.example.com
```
```
root@z1 ~]# pcs cluster standby z1.example.com
```
Copy to Clipboard Toggle word wrap

After putting node z1 in standby mode, check the cluster status. Note that the resources should now all be running on z2.

pcs status
Cluster name: my_cluster
Last updated: Wed Jul 31 17:16:17 2013
Last change: Wed Jul 31 17:18:34 2013 via crm_attribute on z1.example.com
Stack: corosync
Current DC: z2.example.com (2) - partition with quorum
Version: 1.1.10-5.el7-9abe687
2 Nodes configured
6 Resources configured


Node z1.example.com (1): standby
Online: [ z2.example.com ]

Full list of resources:

 myapc	(stonith:fence_apc_snmp):	Started z1.example.com
 Resource Group: apachegroup
     my_lvm	(ocf::heartbeat:LVM):	Started z2.example.com
     my_fs	(ocf::heartbeat:Filesystem):	Started z2.example.com
     VirtualIP	(ocf::heartbeat:IPaddr2):	Started z2.example.com
     Website	(ocf::heartbeat:apache):	Started z2.example.com

[root@z1 ~]# pcs status
Cluster name: my_cluster
Last updated: Wed Jul 31 17:16:17 2013
Last change: Wed Jul 31 17:18:34 2013 via crm_attribute on z1.example.com
Stack: corosync
Current DC: z2.example.com (2) - partition with quorum
Version: 1.1.10-5.el7-9abe687
2 Nodes configured
6 Resources configured


Node z1.example.com (1): standby
Online: [ z2.example.com ]

Full list of resources:

 myapc	(stonith:fence_apc_snmp):	Started z1.example.com 
 Resource Group: apachegroup
     my_lvm	(ocf::heartbeat:LVM):	Started z2.example.com 
     my_fs	(ocf::heartbeat:Filesystem):	Started z2.example.com 
     VirtualIP	(ocf::heartbeat:IPaddr2):	Started z2.example.com 
     Website	(ocf::heartbeat:apache):	Started z2.example.com

Copy to Clipboard

Toggle word wrap

The web site at the defined IP address should still display, without interruption.

To remove z1 from standby mode, enter the following command.
```
root@z1 ~]# pcs cluster unstandby z1.example.com
```
```
root@z1 ~]# pcs cluster unstandby z1.example.com
```
Copy to Clipboard Toggle word wrap
Note
Removing a node from standby mode does not in itself cause the resources to fail back over to that node. For information on controlling which node resources can run on, see the chapter on configuring cluster resources in the Red Hat High Availability Add-On Reference.

맨 위로 이동

이 콘텐츠는 선택한 언어로 제공되지 않습니다.

B.3.5. Testing the Resource Configuration

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat 소개

Theme

Red Hat legal and privacy links

Red Hat legal and privacy links