Red Hat Summit Red Hat Summit지원콘솔개발자평가판 시작연락처

이 콘텐츠는 선택한 언어로 제공되지 않습니다.

B.11. Unable to add bridge br0 port vnet0: No such device

Symptom
The following error message appears: 
Unable to add bridge name_of_bridge port vnet0: No such device
Copy to Clipboard Toggle word wrap
For example, if the bridge name is br0, the error message will appear as: 
Unable to add bridge br0 port vnet0: No such device
Copy to Clipboard Toggle word wrap
In libvirt versions 0.9.6 and earlier, the same error appears as: 
Failed to add tap interface to bridge name_of_bridge: No such device
Copy to Clipboard Toggle word wrap
Or for example, if the bridge is named br0: 
Failed to add tap interface to bridge 'br0': No such device
Copy to Clipboard Toggle word wrap
Investigation
Both error messages reveal that the bridge device specified in the guest's (or domain's) <interface> definition does not exist.
To verify the bridge device listed in the error message does not exist, use the shell command ip addr showbr0.
A message similar to this confirms the host has no bridge by that name: 
br0: error fetching interface information: Device not found
Copy to Clipboard Toggle word wrap
If this is the case, continue to the solution.
However, if the resulting message is similar to the following, the issue exists elsewhere: 
  3: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
      link/ether 1b:c4:94:cf:fd:17 brd ff:ff:ff:ff:ff:ff
      inet 192.168.122.1/24 brd 192.168.122.255 scope global br0
Copy to Clipboard Toggle word wrap
Solution
Edit the existing bridge or create a new bridge with virsh
Use virsh to either edit the settings of an existing bridge or network, or to add the bridge device to the host system configuration.
Edit the existing bridge settings using virsh
Use virsh edit name_of_guest to change the <interface> definition to use a bridge or network that already exists.
For example, change type='bridge' to type='network', and <source bridge='br0'/> to <source network='default'/>.
Create a host bridge using virsh
For libvirt version 0.9.8 and later, a bridge device can be created with the virsh iface-bridge command. This will create a bridge device br0 with eth0, the physical network interface which is set as part of a bridge, attached: 
virsh iface-bridge eth0 br0
Copy to Clipboard Toggle word wrap
Optional: If desired, remove this bridge and restore the original eth0 configuration with this command: 
virsh iface-unbridge br0
Copy to Clipboard Toggle word wrap
Create a host bridge manually
For older versions of libvirt, it is possible to manually create a bridge device on the host. Refer to Section 11.3, “Bridged Networking with libvirt” for instructions.
Red Hat logoGithubredditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다. 최신 업데이트를 확인하세요.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

Theme

© 2026 Red Hat맨 위로 이동