Red Hat Summit Red Hat Summit지원콘솔개발자평가판 시작연락처

8.3. LACP의 OVS DPDK 본딩 구성

다음 목표는 OVS DPDK 내에서 LACP 본딩을 구성하는 것입니다.

8.3.1. Open vSwitch 준비
링크 복사

  1. 대규모 페이지 및 기타 값이 RHEL에 구성되어 있는지 확인합니다. 

    [root@baremetal bonding]# cat /proc/cmdline
BOOT_IMAGE=/boot/vmlinuz-3.10.0-693.17.1.el7.x86_64 root=UUID=fa414390-f78d-49d4-a164-54615a32977b ro console=tty0
console=ttyS0,115200n8 crashkernel=auto rhgb quiet default_hugepagesz=1GB hugepagesz=1G hugepages=32 iommu=pt intel_iommu=on
isolcpus=2,4,6,8,10,12,14,16,18,22,24,26,28,30,32,34,36,38,3,5,7,9,11,13,15,17,19,23,25,27,29,31,33,35,37,39 skew_tick=1
nohz=on nohz_full=2,4,6,8,10,12,14,16,18,22,24,26,28,30,32,34,36,38,3,5,7,9,11,13,15,17,19,23,25,27,29,31,33,35,37,39
rcu_nocbs=2,4,6,8,10,12,14,16,18,22,24,26,28,30,32,34,36,38,3,5,7,9,11,13,15,17,19,23,25,27,29,31,33,35,37,39
tuned.non_isolcpus=00300003 intel_pstate=disable nosoftlockup
    Copy to Clipboard Toggle word wrap

  2. DPDK에 대해 OVS를 구성합니다. 

    [root@baremetal bonding]# ovs-vsctl list Open_vSwitch | grep other
other_config        : {}
[root@baremetal bonding]# ovs-vsctl --no-wait set Open_vSwitch . other_config:pmd-cpu-mask=0x17c0017c
[root@baremetal bonding]# ovs-vsctl --no-wait set Open_vSwitch . other_config:dpdk-lcore-mask=0x00000001
[root@baremetal bonding]# ovs-vsctl --no-wait set Open_vSwitch . other_config:dpdk-init="true"
    Copy to Clipboard Toggle word wrap

  3. 인터페이스를 사용자 공간으로 전환합니다. 

    [root@baremetal bonding]# ethtool -i p1p1 | grep bus
bus-info: 0000:04:00.0
[root@baremetal bonding]# ethtool -i p1p2 | grep bus
bus-info: 0000:04:00.1
[root@baremetal bonding]# driverctl set-override 0000:04:00.0 vfio-pci
[root@baremetal bonding]# driverctl set-override 0000:04:00.1 vfio-pci
    Copy to Clipboard Toggle word wrap

  4. Open vSwitch를 다시 시작, journalctl -u ovs-vswitchd -f & 백그라운드에서 실행: 

    [root@baremetal bonding]# systemctl restart openvswitch
Apr 19 13:02:49 baremetal systemd[1]: Stopping Open vSwitch Forwarding Unit...
Apr 19 13:02:49 baremetal systemd[1]: Stopping Open vSwitch Forwarding Unit...
Apr 19 13:02:49 baremetal ovs-ctl[91399]: Exiting ovs-vswitchd (91202) [  OK  ]
Apr 19 13:02:49 baremetal ovs-ctl[91399]: Exiting ovs-vswitchd (91202) [  OK  ]
Apr 19 13:02:49 baremetal systemd[1]: Starting Open vSwitch Forwarding Unit...
Apr 19 13:02:49 baremetal systemd[1]: Starting Open vSwitch Forwarding Unit...
Apr 19 13:02:49 baremetal ovs-ctl[91483]: Starting ovs-vswitchd EAL: Detected 40 lcore(s)
Apr 19 13:02:49 baremetal ovs-ctl[91483]: Starting ovs-vswitchd EAL: Detected 40 lcore(s)
Apr 19 13:02:49 baremetal ovs-ctl[91483]: EAL: Probing VFIO support...
Apr 19 13:02:49 baremetal ovs-vswitchd[91509]: EAL: Probing VFIO support...
Apr 19 13:02:49 baremetal ovs-ctl[91483]: EAL: VFIO support initialized
Apr 19 13:02:49 baremetal ovs-vswitchd[91509]: EAL: VFIO support initialized
Apr 19 13:02:49 baremetal ovs-ctl[91483]: EAL: Probing VFIO support...
Apr 19 13:02:49 baremetal ovs-vswitchd[91509]: EAL: Probing VFIO support...
Apr 19 13:02:49 baremetal ovs-ctl[91483]: EAL: VFIO support initialized
Apr 19 13:02:49 baremetal ovs-vswitchd[91509]: EAL: VFIO support initialized
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: PCI device 0000:04:00.0 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: PCI device 0000:04:00.0 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:04:00.0 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL:   using IOMMU type 1 (Type 1)
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL:   using IOMMU type 1 (Type 1)
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:04:00.0 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL:   using IOMMU type 1 (Type 1)
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL:   using IOMMU type 1 (Type 1)
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: Ignore mapping IO port bar(2) addr: 3021
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: Ignore mapping IO port bar(2) addr: 3021
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: Ignore mapping IO port bar(2) addr: 3021
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: Ignore mapping IO port bar(2) addr: 3021
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:04:00.1 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:04:00.1 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: PCI device 0000:04:00.1 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: PCI device 0000:04:00.1 on NUMA socket 0
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: Ignore mapping IO port bar(2) addr: 3001
Apr 19 13:02:59 baremetal ovs-ctl[91483]: EAL: Ignore mapping IO port bar(2) addr: 3001
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: Ignore mapping IO port bar(2) addr: 3001
Apr 19 13:02:59 baremetal ovs-vswitchd[91509]: EAL: Ignore mapping IO port bar(2) addr: 3001
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL: PCI device 0000:05:00.0 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL: PCI device 0000:05:00.0 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:05:00.0 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:05:00.0 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL: PCI device 0000:05:00.1 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL: PCI device 0000:05:00.1 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-ctl[91483]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:05:00.1 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL: PCI device 0000:05:00.1 on NUMA socket 0
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-vswitchd[91509]: EAL:   probe driver: 8086:154d net_ixgbe
Apr 19 13:03:00 baremetal ovs-ctl[91483]: [  OK  ]
Apr 19 13:03:00 baremetal ovs-ctl[91483]: [  OK  ]
Apr 19 13:03:00 baremetal ovs-ctl[91483]: Enabling remote OVSDB managers [  OK  ]
Apr 19 13:03:00 baremetal ovs-ctl[91483]: Enabling remote OVSDB managers [  OK  ]
Apr 19 13:03:00 baremetal systemd[1]: Started Open vSwitch Forwarding Unit.
Apr 19 13:03:00 baremetal systemd[1]: Started Open vSwitch Forwarding Unit.
[root@baremetal bonding]#
    Copy to Clipboard Toggle word wrap

8.3.2. LACP 본드 구성
링크 복사

  1. 본딩을 추가합니다. 

    [root@baremetal bonding]# ovs-vsctl add-br ovsbr0  -- set bridge ovsbr0  datapath_type=netdev
[root@baremetal bonding]# ovs-vsctl add-bond ovsbr0 dpdkbond dpdk0 dpdk1     bond_mode=balance-tcp     lacp=active -- set
interface dpdk0 type=dpdk     -- set Interface dpdk1 type=dpdk
    Copy to Clipboard Toggle word wrap

  2. Open vSwitch에서 확인합니다. 

    [root@baremetal bonding]# ovs-appctl lacp/show dpdkbond
---- dpdkbond ----
        status: active negotiated
        sys_id: a0:36:9f:e3:dd:c8
        sys_priority: 65534
        aggregation key: 1
        lacp_time: slow

slave: dpdk0: current attached
        port_id: 2
        port_priority: 65535
        may_enable: true

        actor sys_id: a0:36:9f:e3:dd:c8
        actor sys_priority: 65534
        actor port_id: 2
        actor port_priority: 65535
        actor key: 1
        actor state: activity aggregation synchronized collecting distributing

        partner sys_id: 14:18:77:89:9a:8a
        partner sys_priority: 32768
        partner port_id: 203
        partner port_priority: 32768
        partner key: 1
        partner state: activity timeout aggregation synchronized collecting distributing

slave: dpdk1: current attached
        port_id: 1
        port_priority: 65535
        may_enable: true

        actor sys_id: a0:36:9f:e3:dd:c8
        actor sys_priority: 65534
        actor port_id: 1
        actor port_priority: 65535
        actor key: 1
        actor state: activity aggregation synchronized collecting distributing

        partner sys_id: 14:18:77:89:9a:8a
        partner sys_priority: 32768
        partner port_id: 208
        partner port_priority: 32768
        partner key: 1
        partner state: activity timeout aggregation synchronized collecting distributing

[root@baremetal bonding]# ovs-appctl bond/show dpdkbond
---- dpdkbond ----
bond_mode: balance-tcp
bond may use recirculation: yes, Recirc-ID : 1
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 6817 ms
lacp_status: negotiated
active slave mac: a0:36:9f:e3:dd:c8(dpdk0)

slave dpdk0: enabled
        active slave
        may_enable: true

slave dpdk1: enabled
        may_enable: true
    Copy to Clipboard Toggle word wrap

  3. 스위치에서 확인합니다. 

    S4048-ON-sw#show lacp 1
Port-channel 1 admin up, oper up, mode lacp
LACP Fast Switch-Over Disabled
Actor   System ID:  Priority 32768, Address 1418.7789.9a8a
Partner System ID:  Priority 65534, Address a036.9fe3.ddc8
Actor Admin Key 1, Oper Key 1, Partner Oper Key 1, VLT Peer Oper Key 1
LACP LAG 1 is an aggregatable link
LACP LAG 1 is a normal LAG

A - Active LACP, B - Passive LACP, C - Short Timeout, D - Long Timeout
E - Aggregatable Link, F - Individual Link, G - IN_SYNC, H - OUT_OF_SYNC
I - Collection enabled, J - Collection disabled, K - Distribution enabled
L - Distribution disabled, M - Partner Defaulted, N - Partner Non-defaulted,
O - Receiver is in expired state, P - Receiver is not in expired state

Port Te 1/2 is enabled, LACP is enabled and mode is lacp
Port State: Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEGIKNP Key 1 Priority 32768
  Partner Admin: State BDFHJLMP Key 0 Priority 0
           Oper: State ADEGIKNP Key 1 Priority 65535

Port Te 1/7 is enabled, LACP is enabled and mode is lacp
Port State: Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEGIKNP Key 1 Priority 32768
  Partner Admin: State BDFHJLMP Key 0 Priority 0
           Oper: State ADEGIKNP Key 1 Priority 65535
S4048-ON-sw#
    Copy to Clipboard Toggle word wrap

8.3.3. OVS에서 포트 비활성화 / 비활성화
링크 복사

ovs-ofctl mod-port <bridge> <port> [up|down]을 사용하여 포트를 활성화하거나 비활성화할 수 있습니다.

  1. 포트를 종료합니다. 

    [root@baremetal bonding]#  ovs-ofctl mod-port ovsbr0 dpdk1 down
    Copy to Clipboard Toggle word wrap

  2. 종료를 확인합니다. 

    [root@baremetal bonding]# ovs-appctl lacp/show dpdkbond
---- dpdkbond ----
        status: active negotiated
        sys_id: a0:36:9f:e3:dd:c8
        sys_priority: 65534
        aggregation key: 1
        lacp_time: slow

slave: dpdk0: current attached
        port_id: 2
        port_priority: 65535
        may_enable: true

        actor sys_id: a0:36:9f:e3:dd:c8
        actor sys_priority: 65534
        actor port_id: 2
        actor port_priority: 65535
        actor key: 1
        actor state: activity aggregation synchronized collecting distributing

        partner sys_id: 14:18:77:89:9a:8a
        partner sys_priority: 32768
        partner port_id: 203
        partner port_priority: 32768
        partner key: 1
        partner state: activity timeout aggregation synchronized collecting distributing

slave: dpdk1: defaulted detached
        port_id: 1
        port_priority: 65535
        may_enable: false

        actor sys_id: a0:36:9f:e3:dd:c8
        actor sys_priority: 65534
        actor port_id: 1
        actor port_priority: 65535
        actor key: 1
        actor state: activity aggregation defaulted

        partner sys_id: 00:00:00:00:00:00
        partner sys_priority: 0
        partner port_id: 0
        partner port_priority: 0
        partner key: 0
        partner state:
[root@baremetal bonding]# ovs-appctl bond/show dpdkbond
---- dpdkbond ----
bond_mode: balance-tcp
bond may use recirculation: yes, Recirc-ID : 1
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 3315 ms
lacp_status: negotiated
active slave mac: a0:36:9f:e3:dd:c8(dpdk0)

slave dpdk0: enabled
        active slave
        may_enable: true

slave dpdk1: disabled
        may_enable: false
    Copy to Clipboard Toggle word wrap

  3. 스위치에서 확인합니다. 

    S4048-ON-sw#show lacp 1
Port-channel 1 admin up, oper up, mode lacp
LACP Fast Switch-Over Disabled
Actor   System ID:  Priority 32768, Address 1418.7789.9a8a
Partner System ID:  Priority 65534, Address a036.9fe3.ddc8
Actor Admin Key 1, Oper Key 1, Partner Oper Key 1, VLT Peer Oper Key 1
LACP LAG 1 is an aggregatable link
LACP LAG 1 is a normal LAG

A - Active LACP, B - Passive LACP, C - Short Timeout, D - Long Timeout
E - Aggregatable Link, F - Individual Link, G - IN_SYNC, H - OUT_OF_SYNC
I - Collection enabled, J - Collection disabled, K - Distribution enabled
L - Distribution disabled, M - Partner Defaulted, N - Partner Non-defaulted,
O - Receiver is in expired state, P - Receiver is not in expired state

Port Te 1/2 is enabled, LACP is enabled and mode is lacp
Port State: Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEGIKNP Key 1 Priority 32768
  Partner Admin: State BDFHJLMP Key 0 Priority 0
           Oper: State ADEGIKNP Key 1 Priority 65535

Port Te 1/7 is disabled, LACP is disabled and mode is lacp
Port State: Not in Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEHJLNP Key 1 Priority 32768
  Partner is not present
    Copy to Clipboard Toggle word wrap

  4. 포트를 다시 활성화합니다. 

    [root@baremetal bonding]#  ovs-ofctl mod-port ovsbr0 dpdk1 up
    Copy to Clipboard Toggle word wrap

  5. RHEL에서 확인합니다. 

    [root@baremetal bonding]# ovs-appctl bond/show dpdkbond
---- dpdkbond ----
bond_mode: balance-tcp
bond may use recirculation: yes, Recirc-ID : 1
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 7846 ms
lacp_status: negotiated
active slave mac: a0:36:9f:e3:dd:c8(dpdk0)

slave dpdk0: enabled
        active slave
        may_enable: true

slave dpdk1: enabled
        may_enable: true

[root@baremetal bonding]# ovs-appctl lacp/show dpdkbond
---- dpdkbond ----
        status: active negotiated
        sys_id: a0:36:9f:e3:dd:c8
        sys_priority: 65534
        aggregation key: 1
        lacp_time: slow

slave: dpdk0: current attached
        port_id: 2
        port_priority: 65535
        may_enable: true

        actor sys_id: a0:36:9f:e3:dd:c8
        actor sys_priority: 65534
        actor port_id: 2
        actor port_priority: 65535
        actor key: 1
        actor state: activity aggregation synchronized collecting distributing

        partner sys_id: 14:18:77:89:9a:8a
        partner sys_priority: 32768
        partner port_id: 203
        partner port_priority: 32768
        partner key: 1
        partner state: activity timeout aggregation synchronized collecting distributing

slave: dpdk1: current attached
        port_id: 1
        port_priority: 65535
        may_enable: true

        actor sys_id: a0:36:9f:e3:dd:c8
        actor sys_priority: 65534
        actor port_id: 1
        actor port_priority: 65535
        actor key: 1
        actor state: activity aggregation synchronized collecting distributing

        partner sys_id: 14:18:77:89:9a:8a
        partner sys_priority: 32768
        partner port_id: 208
        partner port_priority: 32768
        partner key: 1
        partner state: activity timeout aggregation synchronized collecting distributing
    Copy to Clipboard Toggle word wrap

  6. 스위치에서 확인합니다. 

    S4048-ON-sw#show lacp 1
Port-channel 1 admin up, oper up, mode lacp
LACP Fast Switch-Over Disabled
Actor   System ID:  Priority 32768, Address 1418.7789.9a8a
Partner System ID:  Priority 65534, Address a036.9fe3.ddc8
Actor Admin Key 1, Oper Key 1, Partner Oper Key 1, VLT Peer Oper Key 1
LACP LAG 1 is an aggregatable link
LACP LAG 1 is a normal LAG

A - Active LACP, B - Passive LACP, C - Short Timeout, D - Long Timeout
E - Aggregatable Link, F - Individual Link, G - IN_SYNC, H - OUT_OF_SYNC
I - Collection enabled, J - Collection disabled, K - Distribution enabled
L - Distribution disabled, M - Partner Defaulted, N - Partner Non-defaulted,
O - Receiver is in expired state, P - Receiver is not in expired state

Port Te 1/2 is enabled, LACP is enabled and mode is lacp
Port State: Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEGIKNP Key 1 Priority 32768
  Partner Admin: State BDFHJLMP Key 0 Priority 0
           Oper: State ADEGIKNP Key 1 Priority 65535

Port Te 1/7 is enabled, LACP is enabled and mode is lacp
Port State: Bundle
  Actor   Admin: State ACEHJLMP Key 1 Priority 32768
           Oper: State ACEGIKNP Key 1 Priority 32768
  Partner Admin: State BDFHJLMP Key 0 Priority 0
           Oper: State ADEGIKNP Key 1 Priority 65535
    Copy to Clipboard Toggle word wrap
Red Hat logoGithubredditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다. 최신 업데이트를 확인하세요.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

Theme

© 2026 Red Hat맨 위로 이동