이 콘텐츠는 선택한 언어로 제공되지 않습니다.

Chapter 2. Configuring the Fujitsu ETERNUS device


Configure storage pools and ports on the device before you define the Fujitsu ETERNUS device as a Block Storage back end. Consult your device documentation for details on each step:

Procedure

  1. Configure a LAN connection between the Controller nodes that host the Block Storage service and the MNT ports of the ETERNUS device.
  2. Configure a SAN connection between the Compute nodes and CA ports of the ETERNUS device.
  3. Log in to the ETERNUS device using an account with the Admin role.
  4. Enable the SMI-S of ETERNUS DX.
  5. Set the SSH key
  6. Add a user account with software role.
  7. Register an Advanced Copy Feature license and configure the copy table size.
  8. Create a storage pool for volumes. You use this pool later in the EternusPool setting in Section 3.1, “Creating driver definitions for each Fujitsu ETERNUS back end”.
  9. Optional: Create a separate storage pool for volume snapshots. This pool represents the EternusSnapPool setting in Section 3.1, “Creating driver definitions for each Fujitsu ETERNUS back end”.
  10. Optional: Create a Snap Data Pool Volume (SDPV) to enable Snap Data Pool (SDP) for the create a snapshot function.

    Tip

    Skip this step if you use a Thin Provision Pool for EternusSnapPool.

  11. Configure storage ports to be used by the Block Storage service.
  12. Set the storage ports ports to CA mode.
  13. To enable host-affinity for the storage ports, enter the following command from the ETERNUS CLI for each port:

    set <PROTO>-parameters -host-affinity enable -port <CM#> <CA#> <PORT>
    Copy to Clipboard Toggle word wrap
    • Replace <PROTO> with the storage protocol, such as fc or iscsi.
    • Replace <CM#> and <CA#> with the name of the controller enclosure where the port is located.
    • Replace <PORT> with the port number.
  14. Use the following commands to generate the SSH key on the undercloud, and upload the eternus.ietf file to the ETERNUS device.

    ssh-keygen -t rsa -N "" -f ./eternus
    ssh-keygen -e -f ./eternus.pub > ./eternus.ietf
    Copy to Clipboard Toggle word wrap
    Note

    Save the eternus file for later use. For security reasons, do not copy or move it from the undercloud or overcloud.

Red Hat logoGithubredditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다. 최신 업데이트를 확인하세요.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

Theme

© 2026 Red Hat
맨 위로 이동