此内容没有您所选择的语言版本。
Chapter 9. The Cluster Configuration File
Configuring a cluster with Conga modifies the cluster configuration file. This chapter shows the cluster configuration file before and after the procedures documented in Chapter 5, Configuring the Cluster Resources and Chapter 6, Configuring an NFS Cluster Service were performed.
Before the cluster resources and service were configured, the cluster.conf file appeared as follows.
<?xml version="1.0"?>
<cluster alias="nfsclust" config_version="1" name="nfsclust">
<fence_daemon post_fail_delay="0" post_join_delay="3"/>
<clusternodes>
<clusternode name="clusternode1.example.com" nodeid="1" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="1"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode2.example.com" nodeid="2" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="2"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode3.example.com" nodeid="3" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="3"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode4.example.com" nodeid="4" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="4"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode5.example.com" nodeid="5" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="5"/>
</method>
</fence>
</clusternode>
</clusternodes>
<cman/>
<fencedevices>
<fencedevice name="apc1" agent="fence_apc" ipaddr="link-apc" login="apc"
passwd="apc"/>
</fencedevices>
<rm/>
</cluster>
After the cluster resources and service were configured, the cluster.conf file appeared as follows.
<?xml version="1.0"?>
<cluster alias="nfsclust" config_version="10" name="nfsclust">
<fence_daemon clean_start="0" post_fail_delay="0" post_join_delay="3"/>
<clusternodes>
<clusternode name="clusternode1.example.com" nodeid="1" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="1"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode2.example.com" nodeid="2" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="2"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode3.example.com" nodeid="3" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="3"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode4.example.com" nodeid="4" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="4"/>
</method>
</fence>
</clusternode>
<clusternode name="clusternode5.example.com" nodeid="5" votes="1">
<fence>
<method name="apc-nfs">
<device name="apc1" switch="3" port="5"/>
</method>
</fence>
</clusternode>
</clusternodes>
<cman/>
<fencedevices>
<fencedevice name="apc1" agent="fence_apc" ipaddr="link-apc" login="apc"
passwd="apc"/>
</fencedevices>
<rm>
<failoverdomains/>
<resources>
<ip address="10.15.86.96" monitor_link="1"/>
<clusterfs device="/dev/myvg/myvol" force_unmount="0"
fsid="39669" fstype="gfs" mountpoint="/mnt/gfs"
name="mygfs" options="rw,localflocks"/>
<nfsexport name="mynfs"/>
<nfsclient allow_recover="1" name="nfsclient1" options="rw"
target="nfsclient1.example.com"/>
<nfsclient allow_recover="1" name="nfsclient2" options="rw"
target="nfsclient2.example.com"/>
<nfsclient allow_recover="1" name="nfsclient3" options="rw"
target="nfsclient3.example.com"/>
<nfsclient allow_recover="1" name="nfsclient4" options="rw"
target="nfsclient4.example.com"/>
<nfsclient allow_recover="1" name="nfsclient5" options="rw"
target="nfsclient5.example.com"/>
</resources>
<service autostart="1" exclusive="0" name="nfssvc" recovery="relocate">
<ip ref="10.15.86.96"/>
<clusterfs ref="mygfs">
<nfsexport ref="mynfs">
<nfsclient ref="nfsclient1"/>
<nfsclient ref="nfsclient2"/>
<nfsclient ref="nfsclient3"/>
<nfsclient ref="nfsclient4"/>
<nfsclient ref="nfsclient5"/>
</nfsexport>
</clusterfs>
</service>
</rm>
</cluster>
