kernel component
A Linux LIO FCoE target causes the bnx2fc driver to perform sequence level error recovery when the target is down. As a consequence, the FCoE session cannot be resumed after the Ethernet link is bounced, the bnx2fc kernel module cannot be unloaded and the FCoE session cannot be removed when running the fcoeadm -d eth0 command. To avoid these problems, do not use the bnx2fc driver with a Linux FCoE target.
kernel component
When using large block size (1MB), the tape driver sometimes returns an EBUSY error. To work around this problem, use a smaller block size, that is 256KB.
kernel component
On some of the older Broadcom tg3 devices, the default Maximum Read Request Size (MRRS) value of 512 byte is known to cause lower performance. It is because these devices perform direct memory access (DMA) requests serially. 1500-byte ethernet packet will be broken into 3 PCIE read requests using 512 byte MRRS. When using a higher MRRS value, the DMA transfer can be faster as fewer requests will be needed. However, the MRRS value is meant to be tuned by system software and not by the driver. PCIE Base spec 3.0 section 7.8.4 contains an implementation note that illustrates how system software might tune the MRRS for all devices in the system. As a result, Broadcom modified the tg3 driver to remove the code that sets the MRRS to 4K bytes so that any value selected by system software (BIOS) will be preserved.
kernel component
The Brocade BFA Fibre Channel and FCoE driver does not currently support dynamic recognition of Logical Unit addition or removal using the sg3_utils utilities (for example, the sg_scan command) or similar functionality. Please consult Brocade directly for a Brocade equivalent of this functionality.
kernel component
iSCSI and FCoE boot support on Broadcom devices is not included in Red Hat Enterprise Linux 6.4. These two features, which are provided by the bnx2i and bnx2fc Broadcom drivers, remain a Technology Preview until further notice.
kexec-tools component
Starting with Red Hat Enterprise Linux 6.0 and later, kexec kdump supports dumping core to the Brtfs file system. However, note that because the findfs utility in busybox does not support Btrfs yet, UUID/LABEL resolving is not functional. Avoid using the UUID/LABEL syntax when dumping core to Btrfs file systems.
trace-cmd component
The trace-cmd service does start on 64-bit PowerPC and IBM System z systems because the sys_enter and sys_exit events do not get enabled on the aforementioned systems.
trace-cmd component
trace-cmd's subcommand, report, does not work on IBM System z systems. This is due to the fact that the CONFIG_FTRACE_SYSCALLS parameter is not set on IBM System z systems.
libfprint component
Red Hat Enterprise Linux 6 only has support for the first revision of the UPEK Touchstrip fingerprint reader (USB ID 147e:2016). Attempting to use a second revision device may cause the fingerprint reader daemon to crash. The following command returns the version of the device being used in an individual machine:
~]$ lsusb -v -d 147e:2016 | grep bcdDevice
kernel component
The Emulex Fibre Channel/Fibre Channel-over-Ethernet (FCoE) driver in Red Hat Enterprise Linux 6 does not support DH-CHAP authentication. DH-CHAP authentication provides secure access between hosts and mass storage in Fibre-Channel and FCoE SANs in compliance with the FC-SP specification. Note, however that the Emulex driver (lpfc) does support DH-CHAP authentication on Red Hat Enterprise Linux 5, from version 5.4. Future Red Hat Enterprise Linux 6 releases may include DH-CHAP authentication.
kernel component
The recommended minimum HBA firmware revision for use with the mpt2sas driver is "Phase 5 firmware" (that is, with version number in the form 05.xx.xx.xx). Note that following this recommendation is especially important on complex SAS configurations involving multiple SAS expanders.
