搜索

此内容没有您所选择的语言版本。

7.3. Recovering from LVM Mirror Failure

download PDF
This section provides an example of recovering from a situation where one leg of an LVM mirrored volume fails because the underlying device for a physical volume goes down and the mirror_log_fault_policy parameter is set to remove, requiring that you manually rebuild the mirror. For information on setting the mirror_log_fault_policy parameter, see Section 5.4.3.1, “Mirrored Logical Volume Failure Policy”.
When a mirror leg fails, LVM converts the mirrored volume into a linear volume, which continues to operate as before but without the mirrored redundancy. At that point, you can add a new disk device to the system to use as a replacement physical device and rebuild the mirror.
The following command creates the physical volumes which will be used for the mirror.
# pvcreate /dev/sd[abcdefgh][12]
  Physical volume "/dev/sda1" successfully created
  Physical volume "/dev/sda2" successfully created
  Physical volume "/dev/sdb1" successfully created
  Physical volume "/dev/sdb2" successfully created
  Physical volume "/dev/sdc1" successfully created
  Physical volume "/dev/sdc2" successfully created
  Physical volume "/dev/sdd1" successfully created
  Physical volume "/dev/sdd2" successfully created
  Physical volume "/dev/sde1" successfully created
  Physical volume "/dev/sde2" successfully created
  Physical volume "/dev/sdf1" successfully created
  Physical volume "/dev/sdf2" successfully created
  Physical volume "/dev/sdg1" successfully created
  Physical volume "/dev/sdg2" successfully created
  Physical volume "/dev/sdh1" successfully created
  Physical volume "/dev/sdh2" successfully created
The following commands creates the volume group vg and the mirrored volume groupfs.
# vgcreate vg /dev/sd[abcdefgh][12]
  Volume group "vg" successfully created
[root@link-08 ~]# lvcreate -L 750M -n groupfs -m 1 vg /dev/sda1 /dev/sdb1 /dev/sdc1
  Rounding up size to full physical extent 752.00 MB
  Logical volume "groupfs" created
You can use the lvs command to verify the layout of the mirrored volume and the underlying devices for the mirror leg and the mirror log. Note that in the first example the mirror is not yet completely synced; you should wait until the Copy% field displays 100.00 before continuing.
# lvs -a -o +devices
  LV                 VG   Attr   LSize   Origin Snap%  Move Log          Copy% Devices
  groupfs            vg   mwi-a- 752.00M                    groupfs_mlog 21.28 groupfs_mimage_0(0),groupfs_mimage_1(0)
  [groupfs_mimage_0] vg   iwi-ao 752.00M                                       /dev/sda1(0)
  [groupfs_mimage_1] vg   iwi-ao 752.00M                                       /dev/sdb1(0)
  [groupfs_mlog]     vg   lwi-ao   4.00M                                       /dev/sdc1(0)

[root@link-08 ~]# lvs -a -o +devices
  LV                 VG   Attr   LSize   Origin Snap%  Move Log          Copy%  Devices
  groupfs            vg   mwi-a- 752.00M                    groupfs_mlog 100.00 groupfs_mimage_0(0),groupfs_mimage_1(0)
  [groupfs_mimage_0] vg   iwi-ao 752.00M                                        /dev/sda1(0)
  [groupfs_mimage_1] vg   iwi-ao 752.00M                                        /dev/sdb1(0)
  [groupfs_mlog]     vg   lwi-ao   4.00M     i                                  /dev/sdc1(0)
In this example, the primary leg of the mirror /dev/sda1 fails. Any write activity to the mirrored volume causes LVM to detect the failed mirror. When this occurs, LVM converts the mirror into a single linear volume. In this case, to trigger the conversion, we execute a dd command
# dd if=/dev/zero of=/dev/vg/groupfs count=10
10+0 records in
10+0 records out
You can use the lvs command to verify that the device is now a linear device. Because of the failed disk, I/O errors occur.
# lvs -a -o +devices
  /dev/sda1: read failed after 0 of 2048 at 0: Input/output error
  /dev/sda2: read failed after 0 of 2048 at 0: Input/output error
  LV      VG   Attr   LSize   Origin Snap%  Move Log Copy%  Devices
  groupfs vg   -wi-a- 752.00M                               /dev/sdb1(0)
At this point you should still be able to use the logical volume, but there will be no mirror redundancy.
To rebuild the mirrored volume, you replace the broken drive and recreate the physical volume. If you use the same disk rather than replacing it with a new one, you will see "inconsistent" warnings when you run the pvcreate command. You can prevent that warning from appearing by executing the vgreduce --removemissing command.
# pvcreate /dev/sdi[12]
  Physical volume "/dev/sdi1" successfully created
  Physical volume "/dev/sdi2" successfully created

[root@link-08 ~]# pvscan
  PV /dev/sdb1   VG vg   lvm2 [67.83 GB / 67.10 GB free]
  PV /dev/sdb2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdc1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdc2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdd1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdd2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sde1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sde2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdf1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdf2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdg1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdg2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdh1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdh2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdi1           lvm2 [603.94 GB]
  PV /dev/sdi2           lvm2 [603.94 GB]
  Total: 16 [2.11 TB] / in use: 14 [949.65 GB] / in no VG: 2 [1.18 TB]
Next you extend the original volume group with the new physical volume.
# vgextend vg /dev/sdi[12]
  Volume group "vg" successfully extended

# pvscan
  PV /dev/sdb1   VG vg   lvm2 [67.83 GB / 67.10 GB free]
  PV /dev/sdb2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdc1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdc2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdd1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdd2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sde1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sde2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdf1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdf2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdg1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdg2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdh1   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdh2   VG vg   lvm2 [67.83 GB / 67.83 GB free]
  PV /dev/sdi1   VG vg   lvm2 [603.93 GB / 603.93 GB free]
  PV /dev/sdi2   VG vg   lvm2 [603.93 GB / 603.93 GB free]
  Total: 16 [2.11 TB] / in use: 16 [2.11 TB] / in no VG: 0 [0   ]
Convert the linear volume back to its original mirrored state.
# lvconvert -m 1 /dev/vg/groupfs /dev/sdi1 /dev/sdb1 /dev/sdc1
  Logical volume mirror converted.
You can use the lvs command to verify that the mirror is restored.
# lvs -a -o +devices
  LV                 VG   Attr   LSize   Origin Snap%  Move Log          Copy% Devices
  groupfs            vg   mwi-a- 752.00M                    groupfs_mlog 68.62 groupfs_mimage_0(0),groupfs_mimage_1(0)
  [groupfs_mimage_0] vg   iwi-ao 752.00M                                       /dev/sdb1(0)
  [groupfs_mimage_1] vg   iwi-ao 752.00M                                       /dev/sdi1(0)
  [groupfs_mlog]     vg   lwi-ao   4.00M                                       /dev/sdc1(0)
Red Hat logoGithubRedditYoutubeTwitter

学习

尝试、购买和销售

社区

关于红帽文档

通过我们的产品和服务,以及可以信赖的内容,帮助红帽用户创新并实现他们的目标。

让开源更具包容性

红帽致力于替换我们的代码、文档和 Web 属性中存在问题的语言。欲了解更多详情,请参阅红帽博客.

關於紅帽

我们提供强化的解决方案,使企业能够更轻松地跨平台和环境(从核心数据中心到网络边缘)工作。

© 2024 Red Hat, Inc.