Dieser Inhalt ist in der von Ihnen ausgewählten Sprache nicht verfügbar.

Appendix A. Boot Devices

Automated installation (or kickstart) is an essential part of efficient system provisioning. This appendix describes how to prepare different types of boot media for use with kickstarting clients.

The Red Hat Enterprise Linux CD boot image boot.iso is a required prerequisite for creating boot devices. Make sure that this is available somewhere on the system and take note of its location.

Important

Install the syslinux and syslinux-extlinux packages to use the following procedures.

yum install syslinux syslinux-extlinux

# yum install syslinux syslinux-extlinux

Copy to Clipboard

Toggle word wrap

The syslinux package installs files in /usr/share/syslinux/ for Red Hat Enterprise Linux 6. If using Red Hat Enterprise Linux 5, substitute this directory with /usr/lib/syslinux/.

The syslinux-extlinux package installs tools for USB boot media creation.

Procedure A.1. CD and DVD Boot Media

Note

The backslash "\" is used below to represent a continuation of one line at the shell prompt.

Create a working directory for the boot image:
```
mkdir -p temp cd/isolinux
```
```
# mkdir -p temp cd/isolinux
```
Copy to Clipboard Toggle word wrap
Mount the boot image to the temp directory:
```
mount -o loop boot.iso temp
```
```
# mount -o loop boot.iso temp
```
Copy to Clipboard Toggle word wrap
Copy the required files for a Boot Media device to the previously created directory:
```
cp -aP temp/isolinux/* cd/isolinux/
```
```
# cp -aP temp/isolinux/* cd/isolinux/
```
Copy to Clipboard Toggle word wrap
Unmount the temp directory and change the permissions on the cd directory to be readable and writable to the user:
```
umount temp
chmod -R u+rw cd
```
```
# umount temp
# chmod -R u+rw cd
```
Copy to Clipboard Toggle word wrap
Change to the ./cd directory:
```
cd ./cd
```
```
# cd ./cd
```
Copy to Clipboard Toggle word wrap
Copy the /usr/share/syslinux/menu.c32 file to the ./cd directory:
```
cp -p /usr/share/syslinux/menu.c32 isolinux
```
```
# cp -p /usr/share/syslinux/menu.c32 isolinux
```
Copy to Clipboard Toggle word wrap
Customize any boot parameters and targets in isolinux.cfg as needed for CD booting.

Use the mkisofs to create an ISO to burn to a CD or DVD.

mkisofs -o ./custom-boot.iso -b isolinux/isolinux.bin -c isolinux/boot.cat -no-emul-boot \
    -boot-load-size 4 -boot-info-table -J -l -r -T -v -V "Custom Red Hat Enterprise Linux Boot" .
    -boot-load-size 4 -boot-info-table -J -l -r -T -v -V "Custom Red Hat Enterprise Linux Boot" .

# mkisofs -o ./custom-boot.iso -b isolinux/isolinux.bin -c isolinux/boot.cat -no-emul-boot \
    -boot-load-size 4 -boot-info-table -J -l -r -T -v -V "Custom Red Hat Enterprise Linux Boot" .

Copy to Clipboard

Toggle word wrap

Burn the directory to a CD or DVD to complete the procedure.

Procedure A.2. PXE Boot

Create a working directory for the boot image:
```
mkdir -p temp pxe/pxelinux.cfg
```
```
# mkdir -p temp pxe/pxelinux.cfg
```
Copy to Clipboard Toggle word wrap
Mount the boot image to the temp directory:
```
mount -o loop boot.iso temp
```
```
# mount -o loop boot.iso temp
```
Copy to Clipboard Toggle word wrap
Copy the required files for a PXE Boot device to the previously created directory:
```
cp -aP temp/isolinux/* pxe/
```
```
# cp -aP temp/isolinux/* pxe/
```
Copy to Clipboard Toggle word wrap
Unmount the temp directory and change the permissions on the cd directory to be readable and writable to the user:
```
umount temp
chmod -R u+rw pxe
```
```
# umount temp
# chmod -R u+rw pxe
```
Copy to Clipboard Toggle word wrap
Change to the /pxe directory:
```
cd ./pxe
```
```
# cd ./pxe
```
Copy to Clipboard Toggle word wrap
Copy the /usr/share/syslinux/menu.c32 file to the /pxe directory:
```
cp -p /usr/share/syslinux/menu.c32 .
```
```
# cp -p /usr/share/syslinux/menu.c32 .
```
Copy to Clipboard Toggle word wrap
Move the isolinux.cfg file to pxelinux.cfg/default:
```
mv isolinux.cfg pxelinux.cfg/default
```
```
# mv isolinux.cfg pxelinux.cfg/default
```
Copy to Clipboard Toggle word wrap
Remove the temporary files:
```
rm -f isolinux.bin TRANS.TBL
```
```
# rm -f isolinux.bin TRANS.TBL
```
Copy to Clipboard Toggle word wrap
Copy the /usr/share/syslinux/pxelinux.0 file to the /pxe directory:
```
cp -p /usr/share/syslinux/pxelinux.0 .
```
```
# cp -p /usr/share/syslinux/pxelinux.0 .
```
Copy to Clipboard Toggle word wrap
Open the pxelinux.cfg/default file in your preferred text editor, and customize any boot parameters and targets as needed for PXE booting.

Procedure A.3. USB Boot Media

Warning

Be extremely careful when carrying out these command as root (required for most critical parts). These commands access device files and using them incorrectly could irrecoverably damage your system. The example below uses /dev/loop0 for mounting, make sure you use the correct device for your system. You can check which is the correct device using the losetup -f command.

Create a working directory for the boot image:
```
mkdir -p temp usb/extlinux
```
```
# mkdir -p temp usb/extlinux
```
Copy to Clipboard Toggle word wrap
Mount the boot image to the temp directory:
```
mount -o loop boot.iso temp
```
```
# mount -o loop boot.iso temp
```
Copy to Clipboard Toggle word wrap
Copy the required files for a USB Media Boot device to the previously created directory:
```
cp -aP temp/isolinux/* usb/extlinux/
```
```
# cp -aP temp/isolinux/* usb/extlinux/
```
Copy to Clipboard Toggle word wrap
Unmount the temp directory and change the permissions on the cd directory to be readable and writable to the user:
```
umount temp
chmod -R u+rw usb
```
```
# umount temp
# chmod -R u+rw usb
```
Copy to Clipboard Toggle word wrap
Copy the /usr/share/syslinux/menu.c32 file to the ./usb/extlinux/ directory:
```
cp -p /usr/share/syslinux/menu.c32 ./usb/extlinux/
```
```
# cp -p /usr/share/syslinux/menu.c32 ./usb/extlinux/
```
Copy to Clipboard Toggle word wrap
Move the usb/extlinux/isolinux.cfg file to usb/extlinux/extlinux.conf:
```
mv usb/extlinux/isolinux.cfg usb/extlinux/extlinux.conf
```
```
# mv usb/extlinux/isolinux.cfg usb/extlinux/extlinux.conf
```
Copy to Clipboard Toggle word wrap

Remove the temporary files:

rm -f usb/extlinux/isolinux.bin usb/extlinux/TRANS.TBL

# rm -f usb/extlinux/isolinux.bin usb/extlinux/TRANS.TBL

Copy to Clipboard

Toggle word wrap

Convert the custom-boot.img file and copy it:

dd if=/dev/zero of=./custom-boot.img bs=1024 count=300000

# dd if=/dev/zero of=./custom-boot.img bs=1024 count=300000

Copy to Clipboard

Toggle word wrap

Discover the correct mounting location for the loopback device:
```
losetup -f
```
```
# losetup -f
/dev/loop0
```
Copy to Clipboard Toggle word wrap
Set up the loopback device with the boot image:
```
losetup /dev/loop0 ./custom-boot.img
```
```
# losetup /dev/loop0 ./custom-boot.img
```
Copy to Clipboard Toggle word wrap
Open the fdisk utility:
```
fdisk /dev/loop0
```
```
# fdisk /dev/loop0
```
Copy to Clipboard Toggle word wrap
Create one primary bootable partition on the device. This can be done by using the following key press combination: n p 1 Enter Enter a 1 p w
Copy the master boot record (MBR) to the loopback device:
```
dd if=/usr/share/syslinux/mbr.bin of=/dev/loop0
```
```
# dd if=/usr/share/syslinux/mbr.bin of=/dev/loop0
```
Copy to Clipboard Toggle word wrap
Add partition maps to the loopback device:
```
kpartx -av /dev/loop0
```
```
# kpartx -av /dev/loop0
```
Copy to Clipboard Toggle word wrap

Create the file system:

mkfs.ext2 -m 0 -L "Custom Red Hat Enterprise Linux Boot" /dev/mapper/loop0p1

# mkfs.ext2 -m 0 -L "Custom Red Hat Enterprise Linux Boot" /dev/mapper/loop0p1

Copy to Clipboard

Toggle word wrap

Mount the device:
```
mount /dev/mapper/loop0p1 temp
```
```
# mount /dev/mapper/loop0p1 temp
```
Copy to Clipboard Toggle word wrap
Delete temporary files:
```
rm -rf temp/lost+found
```
```
# rm -rf temp/lost+found
```
Copy to Clipboard Toggle word wrap
Copy the usb/extlinux/ directory to a temporary location:
```
cp -a usb/extlinux/* temp/
```
```
# cp -a usb/extlinux/* temp/
```
Copy to Clipboard Toggle word wrap
Install the bootloader in the temporary location:
```
extlinux -i temp
```
```
# extlinux -i temp
```
Copy to Clipboard Toggle word wrap
Unmount the temporary location:
```
umount temp
```
```
# umount temp
```
Copy to Clipboard Toggle word wrap
Delete the partition maps on the loopback device:
```
kpartx -dv /dev/loop0
```
```
# kpartx -dv /dev/loop0
```
Copy to Clipboard Toggle word wrap
Delete the loopback device:
```
losetup -d /dev/loop0
```
```
# losetup -d /dev/loop0
```
Copy to Clipboard Toggle word wrap
Synchronize the file system changes:
```
sync
```
```
# sync
```
Copy to Clipboard Toggle word wrap
Open the extlinux.conf file in your preferred text editor, and customize any boot parameters and targets as needed for USB booting.
Transfer the image to a USB device to complete the procedure. Insert the device, and run the dmesg command to check the mounting location. In this example, it is /dev/sdb.
Unmount the USB device:
```
umount /dev/sdb
```
```
# umount /dev/sdb
```
Copy to Clipboard Toggle word wrap
Copy the image to the USB device:
```
dd if=./custom-boot.img of=/dev/sdb
```
```
# dd if=./custom-boot.img of=/dev/sdb
```
Copy to Clipboard Toggle word wrap

Dieser Inhalt ist in der von Ihnen ausgewählten Sprache nicht verfügbar.

Appendix A. Boot Devices

Lernen

Testen, kaufen und verkaufen

Communitys

Über Red Hat Dokumentation

Mehr Inklusion in Open Source

Über Red Hat

Theme

Red Hat legal and privacy links

Red Hat legal and privacy links