Dieser Inhalt ist in der von Ihnen ausgewählten Sprache nicht verfügbar.
3.6. Testing the Resource Configuration
You can validate your system configuration with the following procedure. You should be able to mount the exported file system with either NFSv3 or NFSv4.
- On a node outside of the cluster, residing in the same network as the deployment, verify that the NFS share can be seen by mounting the NFS share. For this example, we are using the 192.168.122.0/24 network.
#
showmount -e 192.168.122.200Export list for 192.168.122.200: /nfsshare/exports/export1 192.168.122.0/255.255.255.0 /nfsshare/exports 192.168.122.0/255.255.255.0 /nfsshare/exports/export2 192.168.122.0/255.255.255.0 - To verify that you can mount the NFS share with NFSv4, mount the NFS share to a directory on the client node. After mounting, verify that the contents of the export directories are visible. Unmount the share after testing.
#
mkdir nfsshare#mount -o "vers=4" 192.168.122.200:export1 nfsshare#ls nfsshareclientdatafile1 #umount nfsshare - Verify that you can mount the NFS share with NFSv3. After mounting, verify that the test file
clientdatafile1is visible. Unlike NFSv4, since NFSV3 does not use the virtual file system, you must mount a specific export. Unmount the share after testing.#
mkdir nfsshare#mount -o "vers=3" 192.168.122.200:/nfsshare/exports/export2 nfsshare#ls nfsshareclientdatafile2 #umount nfsshare - To test for failover, perform the following steps.
- On a node outside of the cluster, mount the NFS share and verify access to the
clientdatafile1we created in Section 3.3, “NFS Share Setup”.#
mkdir nfsshare#mount -o "vers=4" 192.168.122.200:export1 nfsshare#ls nfsshareclientdatafile1 - From a node within the cluster, determine which node in the cluster is running
nfsgroup. In this example,nfsgroupis running onz1.example.com.[root@z1 ~]#
pcs status... Full list of resources: myapc (stonith:fence_apc_snmp): Started z1.example.com Resource Group: nfsgroup my_lvm (ocf::heartbeat:LVM): Started z1.example.com nfsshare (ocf::heartbeat:Filesystem): Started z1.example.com nfs-daemon (ocf::heartbeat:nfsserver): Started z1.example.com nfs-root (ocf::heartbeat:exportfs): Started z1.example.com nfs-export1 (ocf::heartbeat:exportfs): Started z1.example.com nfs-export2 (ocf::heartbeat:exportfs): Started z1.example.com nfs_ip (ocf::heartbeat:IPaddr2): Started z1.example.com nfs-notify (ocf::heartbeat:nfsnotify): Started z1.example.com ... - From a node within the cluster, put the node that is running
nfsgroupin standby mode.[root@z1 ~]#
pcs node standby z1.example.com - Verify that
nfsgroupsuccessfully starts on the other cluster node.[root@z1 ~]#
pcs status... Full list of resources: Resource Group: nfsgroup my_lvm (ocf::heartbeat:LVM): Started z2.example.com nfsshare (ocf::heartbeat:Filesystem): Started z2.example.com nfs-daemon (ocf::heartbeat:nfsserver): Started z2.example.com nfs-root (ocf::heartbeat:exportfs): Started z2.example.com nfs-export1 (ocf::heartbeat:exportfs): Started z2.example.com nfs-export2 (ocf::heartbeat:exportfs): Started z2.example.com nfs_ip (ocf::heartbeat:IPaddr2): Started z2.example.com nfs-notify (ocf::heartbeat:nfsnotify): Started z2.example.com ... - From the node outside the cluster on which you have mounted the NFS share, verify that this outside node still continues to have access to the test file within the NFS mount.
#
ls nfsshareclientdatafile1Service will be lost briefly for the client during the failover briefly but the client should recover in with no user intervention. By default, clients using NFSv4 may take up to 90 seconds to recover the mount; this 90 seconds represents the NFSv4 file lease grace period observed by the server on startup. NFSv3 clients should recover access to the mount in a matter of a few seconds. - From a node within the cluster, remove the node that was initially running running
nfsgroupfrom standby mode. This will not in itself move the cluster resources back to this node.[root@z1 ~]#
pcs node unstandby z1.example.comNote
Removing a node fromstandbymode does not in itself cause the resources to fail back over to that node. This will depend on theresource-stickinessvalue for the resources. For information on theresource-stickinessmeta attribute, see Configuring a Resource to Prefer its Current Node in the Red Hat High Availability Add-On Reference.
