Chapter 10. Known issues

Installation fails on IBM Power 10 systems with LPAR and secure boot enabled

RHEL installer is not integrated with static key secure boot on IBM Power 10 systems. Consequently, when logical partition (LPAR) is enabled with the secure boot option, the installation fails with the error, Unable to proceed with RHEL-x.x Installation.

Unexpected SELinux policies on systems where Anaconda is running as an application

When Anaconda is running as an application on an already installed system (for example to perform another installation to an image file using the –image anaconda option), the system is not prohibited to modify the SELinux types and attributes during installation. As a consequence, certain elements of SELinux policy might change on the system where Anaconda is running. To work around this problem, do not run Anaconda on the production system and execute it in a temporary virtual machine. So that the SELinux policy on a production system is not modified. Running anaconda as part of the system installation process such as installing from boot.iso or dvd.iso is not affected by this issue.

The auth and authconfig Kickstart commands require the AppStream repository

The authselect-compat package is required by the auth and authconfig Kickstart commands during installation. Without this package, the installation fails if auth or authconfig are used. However, by design, the authselect-compat package is only available in the AppStream repository.

The reboot --kexec and inst.kexec commands do not provide a predictable system state

Performing a RHEL installation with the reboot --kexec Kickstart command or the inst.kexec kernel boot parameters do not provide the same predictable system state as a full reboot. As a consequence, switching to the installed system without rebooting can produce unpredictable results.

The USB CD-ROM drive is not available as an installation source in Anaconda

Installation fails when the USB CD-ROM drive is the source for it and the Kickstart ignoredisk --only-use= command is specified. In this case, Anaconda cannot find and use this source disk.

Network access is not enabled by default in the installation program

Several installation features require network access, for example, registration of a system using the Content Delivery Network (CDN), NTP server support, and network installation sources. However, network access is not enabled by default, and as a result, these features cannot be used until network access is enabled.

Hard drive partitioned installations with iso9660 filesystem fails

You cannot install RHEL on systems where the hard drive is partitioned with the iso9660 filesystem. This is due to the updated installation code that is set to ignore any hard disk containing a iso9660 file system partition. This happens even when RHEL is installed without using a DVD.

IBM Power systems with HASH MMU mode fail to boot with memory allocation failures

IBM Power Systems with HASH memory allocation unit (MMU) mode support kdump up to a maximum of 192 cores. Consequently, the system fails to boot with memory allocation failures if kdump is enabled on more than 192 cores. This limitation is due to RMA memory allocations during early boot in HASH MMU mode. To work around this problem, use the Radix MMU mode with fadump enabled instead of using kdump.

syspurpose addons have no effect on the subscription-manager attach --auto output.

In Red Hat Enterprise Linux 8, four attributes of the syspurpose command-line tool have been added: role,usage, service_level_agreement and addons. Currently, only role, usage and service_level_agreement affect the output of running the subscription-manager attach --auto command. Users who attempt to set values to the addons argument will not observe any effect on the subscriptions that are auto-attached.

cr_compress_file_with_stat() can cause a memory leak

The createrepo_c C library has the API cr_compress_file_with_stat() function. This function is declared with char **dst as a second parameter. Depending on its other parameters, cr_compress_file_with_stat() either uses dst as an input parameter, or uses it to return an allocated string. This unpredictable behavior can cause a memory leak, because it does not inform the user when to free dst contents.

YUM transactions reported as successful when a scriptlet fails

Since RPM version 4.6, post-install scriptlets are allowed to fail without being fatal to the transaction. This behavior propagates up to YUM as well. This results in scriptlets which might occasionally fail while the overall package transaction reports as successful.

A security DNF upgrade can skip obsoleted packages

The patch for BZ#2095764, released with the RHBA-2022:5816 advisory, introduced the following regression: The DNF upgrade using security filters, such as the --security option, can skip upgrading obsoleted packages. This issue happens specifically when an installed package is obsoleted by a different available package, and an advisory exists for the available package.

coreutils might report misleading EPERM error codes

GNU Core Utilities (coreutils) started using the statx() system call. If a seccomp filter returns an EPERM error code for unknown system calls, coreutils might consequently report misleading EPERM error codes because EPERM can not be distinguished from the actual Operation not permitted error returned by a working statx() syscall.

Postfix TLS fingerprint algorithm in the FIPS mode needs to be changed to SHA-256

By default in RHEL 8, postfix uses MD5 fingerprints with the TLS for backward compatibility. But in the FIPS mode, the MD5 hashing function is not available, which may cause TLS to incorrectly function in the default postfix configuration. To workaround this problem, the hashing function needs to be changed to SHA-256 in the postfix configuration file.

The brltty package is not multilib compatible

It is not possible to have both 32-bit and 64-bit versions of the brltty package installed. You can either install the 32-bit (brltty.i686) or the 64-bit (brltty.x86_64) version of the package. The 64-bit version is recommended.

File permissions of /etc/passwd- are not aligned with the CIS RHEL 8 Benchmark 1.0.0

Because of an issue with the CIS Benchmark, the remediation of the SCAP rule that ensures permissions on the /etc/passwd- backup file configures permissions to 0644. However, the CIS Red Hat Enterprise Linux 8 Benchmark 1.0.0 requires file permissions 0600 for that file. As a consequence, the file permissions of /etc/passwd- are not aligned with the benchmark after remediation.

libselinux-python is available only through its module

The libselinux-python package contains only Python 2 bindings for developing SELinux applications and it is used for backward compatibility. For this reason, libselinux-python is no longer available in the default RHEL 8 repositories through the yum install libselinux-python command.

udica processes UBI 8 containers only when started with --env container=podman

The Red Hat Universal Base Image 8 (UBI 8) containers set the container environment variable to the oci value instead of the podman value. This prevents the udica tool from analyzing a container JavaScript Object Notation (JSON) file.

SELINUX=disabled in /etc/selinux/config does not work properly

Disabling SELinux using the SELINUX=disabled option in the /etc/selinux/config results in a process in which the kernel boots with SELinux enabled and switches to disabled mode later in the boot process. This might cause memory leaks.

sshd -T provides inaccurate information about Ciphers, MACs and KeX algorithms

The output of the sshd -T command does not contain the system-wide crypto policy configuration or other options that could come from an environment file in /etc/sysconfig/sshd and that are applied as arguments on the sshd command. This occurs because the upstream OpenSSH project did not support the Include directive to support Red-Hat-provided cryptographic defaults in RHEL 8. Crypto policies are applied as command-line arguments to the sshd executable in the sshd.service unit during the service’s start by using an EnvironmentFile. To work around the problem, use the source command with the environment file and pass the crypto policy as an argument to the sshd command, as in sshd -T $CRYPTO_POLICY. For additional information, see Ciphers, MACs or KeX algorithms differ from sshd -T to what is provided by current crypto policy level. As a result, the output from sshd -T matches the currently configured crypto policy.

OpenSSL in FIPS mode accepts only specific D-H parameters

In FIPS mode, TLS clients that use OpenSSL return a bad dh value error and abort TLS connections to servers that use manually generated parameters. This is because OpenSSL, when configured to work in compliance with FIPS 140-2, works only with Diffie-Hellman parameters compliant to NIST SP 800-56A rev3 Appendix D (groups 14, 15, 16, 17, and 18 defined in RFC 3526 and with groups defined in RFC 7919). Also, servers that use OpenSSL ignore all other parameters and instead select known parameters of similar size. To work around this problem, use only the compliant groups.

crypto-policies incorrectly allow Camellia ciphers

The RHEL 8 system-wide cryptographic policies should disable Camellia ciphers in all policy levels, as stated in the product documentation. However, the Kerberos protocol enables the ciphers by default.

Smart-card provisioning process through OpenSC pkcs15-init does not work properly

The file_caching option is enabled in the default OpenSC configuration, and the file caching functionality does not handle some commands from the pkcs15-init tool properly. Consequently, the smart-card provisioning process through OpenSC fails.

Connections to servers with SHA-1 signatures do not work with GnuTLS

SHA-1 signatures in certificates are rejected by the GnuTLS secure communications library as insecure. Consequently, applications that use GnuTLS as a TLS backend cannot establish a TLS connection to peers that offer such certificates. This behavior is inconsistent with other system cryptographic libraries.

IKE over TCP connections do not work on custom TCP ports

The tcp-remoteport Libreswan configuration option does not work properly. Consequently, an IKE over TCP connection cannot be established when a scenario requires specifying a non-default TCP port.

Remediating service-related rules during kickstart installations might fail

During a kickstart installation, the OpenSCAP utility sometimes incorrectly shows that a service enable or disable state remediation is not needed. Consequently, OpenSCAP might set the services on the installed system to a non-compliant state. As a workaround, you can scan and remediate the system after the kickstart installation. This will fix the service-related issues.

RHV hypervisor may not work correctly when hardening the system during installation

When installing Red Hat Virtualization Hypervisor (RHV-H) and applying the Red Hat Enterprise Linux 8 STIG profile, OSCAP Anaconda Add-on may harden the system as RHEL instead of RVH-H and remove essential packages for RHV-H. Consequently, the RHV hypervisor may not work. To work around the problem, install the RHV-H system without applying any profile hardening, and after the installation is complete, apply the profile by using OpenSCAP. As a result, the RHV hypervisor works correctly.

Red Hat provides the CVE OVAL reports in compressed format

Red Hat provides CVE OVAL feeds in the bzip2-compressed format, and they are no longer available in the XML file format. The location of feeds for RHEL 8 has been updated accordingly to reflect this change. Because referencing compressed content is not standardized, third-party SCAP scanners can have problems with scanning rules that use the feed.

Certain sets of interdependent rules in SSG can fail

Remediation of SCAP Security Guide (SSG) rules in a benchmark can fail due to undefined ordering of rules and their dependencies. If two or more rules need to be executed in a particular order, for example, when one rule installs a component and another rule configures the same component, they can run in the wrong order and remediation reports an error. To work around this problem, run the remediation twice, and the second run fixes the dependent rules.

Server with GUI and Workstation installations are not possible with CIS Server profiles

The CIS Server Level 1 and Level 2 security profiles are not compatible with the Server with GUI and Workstation software selections. As a consequence, a RHEL 8 installation with the Server with GUI software selection and CIS Server profiles is not possible. An attempted installation using the CIS Server Level 1 or Level 2 profiles and either of these software selections will generate the error message:

Kickstart uses org_fedora_oscap instead of com_redhat_oscap in RHEL 8

The Kickstart references the Open Security Content Automation Protocol (OSCAP) Anaconda add-on as org_fedora_oscap instead of com_redhat_oscap, which might cause confusion. This is necessary for backwards compatibility backward compatibility with Red Hat Enterprise Linux 7.

SSH timeout rules in STIG profiles configure incorrect options

An update of OpenSSH affected the rules in the following Defense Information Systems Agency Security Technical Implementation Guide (DISA STIG) profiles:

Certain rsyslog priority strings do not work correctly

Support for the GnuTLS priority string for imtcp that allows fine-grained control over encryption is not complete. Consequently, the following priority strings do not work properly in rsyslog:

Negative effects of the default logging setup on performance

The default logging environment setup might consume 4 GB of memory or even more and adjustments of rate-limit values are complex when systemd-journald is running with rsyslog.

Ansible remediations require additional collections

With the replacement of Ansible Engine by the ansible-core package, the list of Ansible modules provided with the RHEL subscription is reduced. As a consequence, running remediations that use Ansible content included within the scap-security-guide package requires collections from the rhc-worker-playbook package.

The nm-cloud-setup service removes manually-configured secondary IP addresses from interfaces

Based on the information received from the cloud environment, the nm-cloud-setup service configures network interfaces. Disable nm-cloud-setup to manually configure interfaces. However, in certain cases, other services on the host can configure interfaces as well. For example, these services could add secondary IP addresses. To avoid that nm-cloud-setup removes secondary IP addresses:

The primary IP address of an instance changes after starting the nm-cloud-setup service in Alibaba Cloud

After launching an instance in the Alibaba Cloud, the nm-cloud-setup service assigns the primary IP address to an instance. However, if you assign multiple secondary IP addresses to an instance and start the nm-cloud-setup service, the former primary IP address gets replaced by one of the already assigned secondary IP addresses. The returned list of metadata verifies the same. To work around the problem, configure secondary IP addresses manually to avoid that the primary IP address changes. As a result, an instance retains both IP addresses and the primary IP address does not change.

NetworkManager does not support activating bond and team ports in a specific order

NetworkManager activates interfaces alphabetically by interface names. However, if an interface appears later during the boot, for example, because the kernel needs more time to discover it, NetworkManager activates this interface later. NetworkManager does not support setting a priority on bond and team ports. Consequently, the order in which NetworkManager activates ports of these devices is not always predictable. To work around this problem, write a dispatcher script.

Systems with the IPv6_rpfilter option enabled experience low network throughput

Systems with the IPv6_rpfilter option enabled in the firewalld.conf file currently experience suboptimal performance and low network throughput in high traffic scenarios, such as 100-Gbps links. To work around the problem, disable the IPv6_rpfilter option. To do so, add the following line in the /etc/firewalld/firewalld.conf file.

RoCE interfaces lose their IP settings due to an unexpected change of the network interface name

The RDMA over Converged Ethernet (RoCE) interfaces lose their IP settings due to an unexpected change of the network interface name if both conditions are met:

Using net_prio or net_cls controllers in v1 mode deactivates some controllers of the cgroup-v2 hierarchy

In cgroup-v2 environments, using either net_prio or net_cls controllers in v1 mode disables the hierarchical tracking of socket data. As a result, the cgroup-v2 hierarchy for socket data tracking controllers is not active, and the dmesg command reports the following message:

Anaconda in some cases fails after entering the passphrase for encrypted devices

If kdump is disabled when preparing an installation and the user selects encrypted disk partitioning, the Anaconda installer fails with a traceback after entering the passphrase for the encrypted device.

Reloading an identical crash extension may cause segmentation faults

When you load a copy of an already loaded crash extension file, it might trigger a segmentation fault. Currently, the crash utility detects if an original file has been loaded. Consequently, due to two identical files co-existing in the crash utility, a namespace collision occurs, which triggers the crash utility to cause a segmentation fault.

vmcore capture fails after memory hot-plug or unplug operation

After performing the memory hot-plug or hot-unplug operation, the event comes after updating the device tree which contains memory layout information. Thereby the makedumpfile utility tries to access a non-existent physical address. The problem appears if all of the following conditions meet:

Debug kernel fails to boot in crash capture environment on RHEL 8

Due to the memory-intensive nature of the debug kernel, a problem occurs when the debug kernel is in use and a kernel panic is triggered. As a consequence, the debug kernel is not able to boot as the capture kernel and a stack trace is generated instead. To work around this problem, increase the crash kernel memory as required. As a result, the debug kernel boots successfully in the crash capture environment.

Allocating crash kernel memory fails at boot time

On some Ampere Altra systems, allocating the crash kernel memory during boot fails when the 32-bit region is disabled in BIOS settings. Consequently, the kdump service fails to start. This is caused by memory fragmentation in the region below 4 GB with no fragment being large enough to contain the crash kernel memory.

The kernel ACPI driver reports it has no access to a PCIe ECAM memory region

The Advanced Configuration and Power Interface (ACPI) table provided by firmware does not define a memory region on the PCI bus in the Current Resource Settings (_CRS) method for the PCI bus device. Consequently, the following warning message occurs during the system boot:

The tuned-adm profile powersave command causes the system to become unresponsive

Executing the tuned-adm profile powersave command leads to an unresponsive state of the Penguin Valkyrie 2000 2-socket systems with the older Thunderx (CN88xx) processors. Consequently, reboot the system to resume working. To work around this problem, avoid using the powersave profile if your system matches the mentioned specifications.

The HP NMI watchdog does not always generate a crash dump

In certain cases, the hpwdt driver for the HP NMI watchdog is not able to claim a non-maskable interrupt (NMI) generated by the HPE watchdog timer because the NMI was instead consumed by the perfmon driver.

Using irqpoll causes vmcore generation failure

Due to an existing problem with the nvme driver on the 64-bit ARM architecture that run on the Amazon Web Services Graviton 1 processor, causes vmcore generation to fail when you provide the irqpoll kernel command line parameter to the first kernel. Consequently, no vmcore file is dumped in the /var/crash/ directory upon a kernel crash. To work around this problem:

Connections fail when attaching a virtual function to virtual machine

Pensando network cards that use the ionic device driver silently accept VLAN tag configuration requests and attempt configuring network connections while attaching network virtual functions (VF) to a virtual machine (VM). Such network connections fail as this feature is not yet supported by the card’s firmware.

The OPEN MPI library may trigger run-time failures with default PML

In OPEN Message Passing Interface (OPEN MPI) implementation 4.0.x series, Unified Communication X (UCX) is the default point-to-point communicator (PML). The later versions of OPEN MPI 4.0.x series deprecated openib Byte Transfer Layer (BTL).

The Solarflare fails to create maximum number of virtual functions (VFs)

The Solarflare NICs fail to create a maximum number of VFs due to insufficient resources. You can check the maximum number of VFs that a PCIe device can create in the /sys/bus/pci/devices/PCI_ID/sriov_totalvfs file. To workaround this problem, you can either adjust the number of VFs or the VF MSI interrupt value to a lower value, either from Solarflare Boot Manager on startup, or using Solarflare sfboot utility. The default VF MSI interrupt value is 8.

Memory allocation for kdump fails on the 64-bit ARM architectures

On certain 64-bit ARM based systems, the firmware uses the non-contiguous memory allocation method, which reserves memory randomly at different scattered locations. Consequently, due to the unavailability of consecutive blocks of memory, the crash kernel cannot reserve memory space for the kdump mechanism.

Hardware certification of the real-time kernel on systems with large core-counts might require passing the skew-tick=1 boot parameter to avoid lock contentions

Large or moderate sized systems with numerous sockets and large core-counts can experience latency spikes due to lock contentions on xtime_lock, which is used in the timekeeping system. As a consequence, latency spikes and delays in hardware certifications might occur on multiprocessing systems. As a workaround, you can offset the timer tick per CPU to start at a different time by adding the skew_tick=1 boot parameter.

Limitations of LVM writecache

The writecache LVM caching method has the following limitations, which are not present in the cache method:

XFS quota warnings are triggered too often

Using the quota timer results in quota warnings triggering too often, which causes soft quotas to be enforced faster than they should. To work around this problem, do not use soft quotas, which will prevent triggering warnings. As a result, the amount of warning messages will not enforce soft quota limit anymore, respecting the configured timeout.

LVM mirror devices that store a LUKS volume sometimes become unresponsive

Mirrored LVM devices with a segment type of mirror that store a LUKS volume might become unresponsive under certain conditions. The unresponsive devices reject all I/O operations.

The /boot file system cannot be placed on LVM

You cannot place the /boot file system on an LVM logical volume. This limitation exists for the following reasons:

LVM no longer allows creating volume groups with mixed block sizes

LVM utilities such as vgcreate or vgextend no longer allow you to create volume groups (VGs) where the physical volumes (PVs) have different logical block sizes. LVM has adopted this change because file systems fail to mount if you extend the underlying logical volume (LV) with a PV of a different block size.

Using Device mapper multipath with the NVMe/TCP driver causes system instability

DM multipath is not supported with the NVMe/TCP driver. Using it causes sleeping functions in the kernel to be called in an atomic context, which then results in system instability.

The blk-availability systemd service deactivates complex device stacks

In systemd, the default block deactivation code does not always handle complex stacks of virtual block devices correctly. In some configurations, virtual devices might not be removed during the shutdown, which causes error messages to be logged. To work around this problem, deactivate complex block device stacks by executing the following command:

getpwnam() might fail when called by a 32-bit application

When a user of NIS uses a 32-bit application that calls the getpwnam() function, the call fails if the nss_nis.i686 package is missing. To work around this problem, manually install the missing package by using the yum install nss_nis.i686 command.

MariaDB 10.5 does not warn about dropping a non-existent table when the OQGraph plug-in is enabled

When the OQGraph storage engine plug-in is loaded to the MariaDB 10.5 server, MariaDB does not warn about dropping a non-existent table. In particular, when the user attempts to drop a non-existent table using the DROP TABLE or DROP TABLE IF EXISTS SQL commands, MariaDB neither returns an error message nor logs a warning.

PAM plug-in version 1.0 does not work in MariaDB

MariaDB 10.3 provides the Pluggable Authentication Modules (PAM) plug-in version 1.0. MariaDB 10.5 provides the plug-in versions 1.0 and 2.0, version 2.0 is the default.

Symbol conflicts between OpenLDAP libraries might cause crashes in httpd

When both the libldap and libldap_r libraries provided by OpenLDAP are loaded and used within a single process, symbol conflicts between these libraries might occur. Consequently, Apache httpd child processes using the PHP ldap extension might terminate unexpectedly if the mod_security or mod_auth_openidc modules are also loaded by the httpd configuration.

Windows Server 2008 R2 and earlier no longer supported

In RHEL 8.4 and later, Identity Management (IdM) does not support establishing trust to Active Directory with Active Directory domain controllers running Windows Server 2008 R2 or earlier versions. RHEL IdM now requires SMB encryption when establishing the trust relationship, which is only available with Windows Server 2012 or later.

Using the cert-fix utility with the --agent-uid pkidbuser option breaks Certificate System

Using the cert-fix utility with the --agent-uid pkidbuser option corrupts the LDAP configuration of Certificate System. As a consequence, Certificate System might become unstable and manual steps are required to recover the system.

The /var/log/lastlog sparse file on IdM hosts can cause performance problems

During the IdM installation, a range of 200,000 UIDs from a total of 10,000 possible ranges is randomly selected and assigned. Selecting a random range in this way significantly reduces the probability of conflicting IDs in case you decide to merge two separate IdM domains in the future.

FIPS mode does not support using a shared secret to establish a cross-forest trust

Establishing a cross-forest trust using a shared secret fails in FIPS mode because NTLMSSP authentication is not FIPS-compliant. To work around this problem, authenticate with an Active Directory (AD) administrative account when establishing a trust between an IdM domain with FIPS mode enabled and an AD domain.

FreeRADIUS server fails to run in FIPS mode

By default, in FIPS mode, OpenSSL disables the use of the MD5 digest algorithm. As the RADIUS protocol requires MD5 to encrypt a secret between the RADIUS client and the RADIUS server, this causes the FreeRADIUS server to fail in FIPS mode.

Actions required when running Samba as a print server and updating from RHEL 8.4 and earlier

With this update, the samba package no longer creates the /var/spool/samba/ directory. If you use Samba as a print server and use /var/spool/samba/ in the [printers] share to spool print jobs, SELinux prevents Samba users from creating files in this directory. Consequently, print jobs fail and the auditd service logs a denied message in /var/log/audit/audit.log. To avoid this problem after updating your system from 8.4 and earlier:

Downgrading authselect after the rebase to version 1.2.2 breaks system authentication

The authselect package has been rebased to the latest upstream version 1.2.2. Downgrading authselect is not supported and breaks system authentication for all users, including root.

The default keyword for enabled ciphers in the NSS does not work in conjunction with other ciphers

In Directory Server you can use the default keyword to refer to the default ciphers enabled in the network security services (NSS). However, if you want to enable the default ciphers and additional ones using the command line or web console, Directory Server fails to resolve the default keyword. As a consequence, the server enables only the additionally specified ciphers and logs the following error:

Potential risk when using the default value for ldap_id_use_start_tls option

When using ldap:// without TLS for identity lookups, it can pose a risk for an attack vector. Particularly a man-in-the-middle (MITM) attack which could allow an attacker to impersonate a user by altering, for example, the UID or GID of an object returned in an LDAP search.

Disabling flatpak repositories from Software Repositories is not possible

Currently, it is not possible to disable or remove flatpak repositories in the Software Repositories tool in the GNOME Software utility.

Generation 2 RHEL 8 virtual machines sometimes fail to boot on Hyper-V Server 2016 hosts

When using RHEL 8 as the guest operating system on a virtual machine (VM) running on a Microsoft Hyper-V Server 2016 host, the VM in some cases fails to boot and returns to the GRUB boot menu. In addition, the following error is logged in the Hyper-V event log:

Drag-and-drop does not work between desktop and applications

Due to a bug in the gnome-shell-extensions package, the drag-and-drop functionality does not currently work between desktop and applications. Support for this feature will be added back in a future release.

radeon fails to reset hardware correctly

The radeon kernel driver currently does not reset hardware in the kexec context correctly. Instead, radeon falls over, which causes the rest of the kdump service to fail.

Multiple HDR displays on a single MST topology may not power on

On systems using NVIDIA Turing GPUs with the nouveau driver, using a DisplayPort hub (such as a laptop dock) with multiple monitors which support HDR plugged into it may result in failure to turn on. This is due to the system erroneously thinking there is not enough bandwidth on the hub to support all of the displays.

GUI in ESXi might crash due to low video memory

The graphical user interface (GUI) on RHEL virtual machines (VMs) in the VMware ESXi 7.0.1 hypervisor with vCenter Server 7.0.1 requires a certain amount of video memory. If you connect multiple consoles or high-resolution monitors to the VM, the GUI requires at least 16 MB of video memory. If you start the GUI with less video memory, the GUI might terminate unexpectedly.

VNC Viewer displays wrong colors with the 16-bit color depth on IBM Z

The VNC Viewer application displays wrong colors when you connect to a VNC session on an IBM Z server with the 16-bit color depth.

Unable to run graphical applications using sudo command

When trying to run graphical applications as a user with elevated privileges, the application fails to open with an error message. The failure happens because Xwayland is restricted by the Xauthority file to use regular user credentials for authentication.

Hardware acceleration is not supported on ARM

Built-in graphics drivers do not support hardware acceleration or the Vulkan API on the 64-bit ARM architecture.

Removing USB host devices using the web console does not work as expected

When you attach a USB device to a virtual machine (VM), the device number and bus number of the USB device might change after they are passed to the VM. As a consequence, using the web console to remove such devices fails due to the incorrect correlation of the device and bus numbers. To workaround this problem, remove the <hostdev> part of the USB device, from the VM’s XML configuration.

Attaching multiple host devices using the web console does not work

When you select multiple devices to attach to a virtual machine (VM) using the web console, only a single device is attached and the rest are ignored. To work around this problem, attach only one device at a time.

Unable to manage localhost by using the localhost hostname in the playbook or inventory

With the inclusion of the ansible-core 2.12 package in RHEL, if you are running Ansible on the same host you manage your nodes, you cannot do it by using the localhost hostname in your playbook or inventory. This happens because ansible-core 2.12 uses the python38 module, and many of the libraries are missing, for example, blivet for the storage role, gobject for the network role. To workaround this problem, if you are already using the localhost hostname in your playbook or inventory, you can add a connection, by using ansible_connection=local, or by creating an inventory file that lists localhost with the ansible_connection=local option. With that, you are able to manage resources on localhost. For more details, see the article RHEL system roles playbooks fail when run on localhost.

Network traffic performance in virtual machines might be reduced

In some cases, RHEL 8.6 guest virtual machines (VMs) have somewhat decreased performance when handling high levels of network traffic.

Using a large number of queues might cause Windows virtual machines to fail

Windows virtual machines (VMs) might fail when the virtual Trusted Platform Module (vTPM) device is enabled and the multi-queue virtio-net feature is configured to use more than 250 queues.

Live post-copy migration of VMs with failover VFs does not work

Currently, attempting to post-copy migrate a running virtual machine (VM) fails if the VM uses a device with the virtual function (VF) failover capability enabled. To work around the problem, use the standard migration type, rather than post-copy migration.

Live migrating VMs to a RHEL 8.6 Intel host from an earlier minor version of RHEL 8 does not work

Because the Intel Transactional Synchronization Extensions (TSX) feature has become deprecated, RHEL 8.6 hosts on Intel hardware no longer use the hle and rtm CPU flags. As a consequence, live migrating a virtual machine (VM) to a RHEL 8.6 host fails if the source host uses RHEL 8.5 or an earlier minor version of RHEL 8.

The Milan VM CPU type is sometimes not available on AMD Milan systems

On certain AMD Milan systems, the Enhanced REP MOVSB (erms) and Fast Short REP MOVSB (fsrm) feature flags are disabled in the BIOS by default. Consequently, the 'Milan' CPU type might not be available on these systems. In addition, VM live migration between Milan hosts with different feature flag settings might fail. To work around these problems, manually turn on erms and fsrm in the BIOS of your host.

Attaching LUN devices to virtual machines using virtio-blk does not work

The q35 machine type does not support transitional virtio 1.0 devices, and RHEL 8 therefore lacks support for features that were deprecated in virtio 1.0. In particular, it is not possible on a RHEL 8 host to send SCSI commands from virtio-blk devices. As a consequence, attaching a physical disk as a LUN device to a virtual machine fails when using the virtio-blk controller.

Virtual machines with iommu_platform=on fail to start on IBM POWER

RHEL 8 currently does not support the iommu_platform=on parameter for virtual machines (VMs) on IBM POWER system. As a consequence, starting a VM with this parameter on IBM POWER hardware results in the VM becoming unresponsive during the boot process.

IBM POWER hosts may crash when using the ibmvfc driver

When running RHEL 8 on a PowerVM logical partition (LPAR), a variety of errors may currently occur due to problems with the ibmvfc driver. As a consequence, the host’s kernel may panic under certain circumstances, such as:

Using perf kvm record on IBM POWER Systems can cause the VM to crash

When using a RHEL 8 host on the little-endian variant of IBM POWER hardware, using the perf kvm record command to collect trace event samples for a KVM virtual machine (VM) in some cases results in the VM becoming unresponsive. This situation occurs when:

Windows Server 2016 virtual machines with Hyper-V enabled fail to boot when using certain CPU models

Currently, it is not possible to boot a virtual machine (VM) that uses Windows Server 2016 as the guest operating system, has the Hyper-V role enabled, and uses one of the following CPU models:

Migrating a POWER9 guest from a RHEL 7-ALT host to RHEL 8 fails

Currently, migrating a POWER9 virtual machine from a RHEL 7-ALT host system to RHEL 8 becomes unresponsive with a Migration status: active status.

Using virt-customize sometimes causes guestfs-firstboot to fail

After modifying a virtual machine (VM) disk image using the virt-customize utility, the guestfs-firstboot service in some cases fails due to incorrect SELinux permissions. This causes a variety of problems during VM startup, such as failing user creation or system registration.

Deleting a forward interface from a macvtap virtual network resets all connection counts of this network

Currently, deleting a forward interface from a macvtap virtual network with multiple forward interfaces also resets the connection status of the other forward interfaces of the network. As a consequence, the connection information in the live network XML is incorrect. Note, however, that this does not affect the functionality of the virtual network. To work around the issue, restart the libvirtd service on your host.

Virtual machines with SLOF fail to boot in netcat interfaces

When using a netcat (nc) interface to access the console of a virtual machine (VM) that is currently waiting at the Slimline Open Firmware (SLOF) prompt, the user input is ignored and VM stays unresponsive. To work around this problem, use the nc -C option when connecting to the VM, or use a telnet interface instead.

Attaching mediated devices to virtual machines in virt-manager in some cases fails

The virt-manager application is currently able to detect mediated devices, but cannot recognize whether the device is active. As a consequence, attempting to attach an inactive mediated device to a running virtual machine (VM) using virt-manager fails. Similarly, attempting to create a new VM that uses an inactive mediated device fails with a device not found error.

RHEL 9 virtual machines fail to boot in POWER8 compatibility mode

Currently, booting a virtual machine (VM) that runs RHEL 9 as its guest operating system fails if the VM also uses CPU configuration similar to the following:

Virtual machines sometimes fail to start when using many virtio-blk disks

Adding a large number of virtio-blk devices to a virtual machine (VM) may exhaust the number of interrupt vectors available in the platform. If this occurs, the VM’s guest OS fails to boot, and displays a dracut-initqueue[392]: Warning: Could not boot error.

Windows Server 2022 guests in some cases boot very slowly on AMD Milan

Virtual machines (VMs) that use the Windows Server 2022 guest operating system and the qemu64 CPU model currently take a very long time to boot on hosts with an AMD EPYC 7003 series processor (also known as AMD Milan).

SMT CPU topology is not detected by VMs when using host passthrough mode on AMD EPYC

When a virtual machine (VM) boots with the CPU host passthrough mode on an AMD EPYC host, the TOPOEXT CPU feature flag is not present. Consequently, the VM is not able to detect a virtual CPU topology with multiple threads per core. To work around this problem, boot the VM with the EPYC CPU model instead of host passthrough.

Migrating VMs to a later z-stream versions of RHEL 8.6 sometimes fails

Attempting to migrate a virtual machine (VM) fails if the destination host uses a RHEL 8.6 version with the qemu-kvm package version 6.2.0-11.module+el8.6.0+21121 and later, and the source host uses qemu-kvm version 6.2.0-11.module+el8.6.0+21120 or earlier on RHEL 8.6.

SR-IOV performs suboptimally in ARM 64 RHEL 8 virtual machines on Azure

Currently, SR-IOV networking devices have significantly lower throughout and higher latency than expected in ARM 64 RHEL 8 virtual machines (VMs) running on a Microsoft Azure platform.

Setting static IP in a RHEL 8 virtual machine on a VMware host does not work

Currently, when using RHEL 8 as a guest operating system of a virtual machine (VM) on a VMware host, the DatasourceOVF function does not work correctly. As a consequence, if you use the cloud-init utility to set the VM’s network to static IP and then reboot the VM, the VM’s network will be changed to DHCP.

kdump sometimes does not start on Azure and Hyper-V

On RHEL 8 guest operating systems hosted on the Microsoft Azure or Hyper-V hypervisors, starting the kdump kernel in some cases fails when post-exec notifiers are enabled.

The SCSI host address sometimes changes when booting a Hyper-V VM with multiple guest disks

Currently, when booting a RHEL 8 virtual machine (VM) on the Hyper-V hypervisor, the host portion of the Host, Bus, Target, Lun (HBTL) SCSI address in some cases changes. As a consequence, automated tasks set up with the HBTL SCSI identification or device node in the VM do not work consistently. This occurs if the VM has more than one disk or if the disks have different sizes.

Starting a RHEL 8 virtual machine on AWS using cloud-init takes longer than expected

Currently, initializing an EC2 instance of RHEL 8 using the cloud-init service on Amazon Web Services (AWS) takes an excessive amount of time. To avoid this problem, remove the /etc/resolv.conf file from the image you are using for VM creation before uploading the image to AWS.

The getattachment command fails to download multiple attachments

The getattachment command is able to download only a single attachment, but fails to download multiple attachments.

redhat-support-tool does not work with the FUTURE crypto policy

Because a cryptographic key used by a certificate on the Customer Portal API does not meet the requirements by the FUTURE system-wide cryptographic policy, the redhat-support-tool utility does not work with this policy level at the moment.

Timeout when running sos report on IBM Power Systems, Little Endian

When running the sos report command on IBM Power Systems, Little Endian with hundreds or thousands of CPUs, the processor plugin reaches its default timeout of 300 seconds when collecting huge content of the /sys/devices/system/cpu directory. As a workaround, increase the plugin’s timeout accordingly:

Running systemd within an older container image does not work

Running systemd within an older container image, for example, centos:7, does not work:

Container images signed with a Beta GPG key can not be pulled

Currently, when you try to pull RHEL Beta container images, podman exits with the error message: Error: Source image rejected: None of the signatures were accepted. The images fail to be pulled due to current builds being configured to not trust the RHEL Beta GPG keys by default.