Chapter 4. Reviewing a system using tuna interface

Procedure

• Install the tuna tool:

  # yum install tuna

  Copy to Clipboard Toggle word wrap

Verification

• Display the available tuna CLI options:

  # tuna -h

  Copy to Clipboard Toggle word wrap

Prerequisites

• The tuna tool is installed. For more information, see Installing tuna tool.

Procedure

• To view the current policies and priorities:

  # tuna --show_threads
              thread
  pid   SCHED_ rtpri affinity             cmd
  1      OTHER     0      0,1            init
  2       FIFO    99        0     migration/0
  3      OTHER     0        0     ksoftirqd/0
  4       FIFO    99        0      watchdog/0

  Copy to Clipboard Toggle word wrap

• To view a specific thread corresponding to a PID or matching a command name:

  # tuna --threads=pid_or_cmd_list --show_threads

  Copy to Clipboard Toggle word wrap

  The pid_or_cmd_list argument is a list of comma-separated PIDs or command-name patterns.

• To tune CPUs using the tuna CLI, see Tuning CPUs using tuna tool.
• To tune the IRQs using the tuna tool, see Tuning IRQs using tuna tool.

• To save the changed configuration:

  # tuna --save=filename

  Copy to Clipboard Toggle word wrap

  This command saves only currently running kernel threads. Processes that are not running are not saved.

Prerequisites

• The tuna tool is installed. For more information, see Installing tuna tool.

Procedure

• To specify the list of CPUs to be affected by a command:

  # tuna --cpus=cpu_list [command]

  Copy to Clipboard Toggle word wrap

  The cpu_list argument is a list of comma-separated CPU numbers. For example, --cpus=0,2. CPU lists can also be specified in a range, for example --cpus=”1-3”, which would select CPUs 1, 2, and 3.

  To add a specific CPU to the current cpu_list, for example, use --cpus=+0.

  Replace [command] with, for example, --isolate.

• To isolate a CPU:

  # tuna --cpus=cpu_list --isolate

  Copy to Clipboard Toggle word wrap

• To include a CPU:

  # tuna --cpus=cpu_list --include

  Copy to Clipboard Toggle word wrap

• To use a system with four or more processors, display how to make all the ssh threads run on CPU 0 and 1, and all the http threads on CPU 2 and 3:

  # tuna --cpus=0,1 --threads=ssh\* \
  --move --cpus=2,3 --threads=http\* --move

  Copy to Clipboard Toggle word wrap

  This command performs the following operations sequentially:

  1. Selects CPUs 0 and 1.
  2. Selects all threads that begin with ssh.
  3. Moves the selected threads to the selected CPUs. Tuna sets the affinity mask of threads starting with ssh to the appropriate CPUs. The CPUs can be expressed numerically as 0 and 1, in hex mask as 0x3, or in binary as 11.
  4. Resets the CPU list to 2 and 3.
  5. Selects all threads that begin with http.
  6. Moves the selected threads to the specified CPUs. Tuna sets the affinity mask of threads starting with http to the specified CPUs. The CPUs can be expressed numerically as 2 and 3, in hex mask as 0xC, or in binary as 1100.

Verification

• Display the current configuration and verify that the changes were performed as expected:

  # tuna --threads=gnome-sc\* --show_threads \
  --cpus=0 --move --show_threads --cpus=1 \
  --move --show_threads --cpus=+0 --move --show_threads
  
                         thread       ctxt_switches
       pid SCHED_ rtpri affinity voluntary nonvoluntary             cmd
     3861   OTHER     0      0,1     33997           58 gnome-screensav
                         thread       ctxt_switches
       pid SCHED_ rtpri affinity voluntary nonvoluntary             cmd
     3861   OTHER     0        0     33997           58 gnome-screensav
                         thread       ctxt_switches
       pid SCHED_ rtpri affinity voluntary nonvoluntary             cmd
     3861   OTHER     0        1     33997           58 gnome-screensav
                         thread       ctxt_switches
       pid SCHED_ rtpri affinity voluntary nonvoluntary             cmd
     3861   OTHER     0      0,1     33997           58 gnome-screensav

  Copy to Clipboard Toggle word wrap

  This command performs the following operations sequentially:

  1. Selects all threads that begin with the gnome-sc threads.
  2. Displays the selected threads to enable the user to verify their affinity mask and RT priority.
  3. Selects CPU 0.
  4. Moves the gnome-sc threads to the specified CPU, CPU 0.
  5. Shows the result of the move.
  6. Resets the CPU list to CPU 1.
  7. Moves the gnome-sc threads to the specified CPU, CPU 1.
  8. Displays the result of the move.
  9. Adds CPU 0 to the CPU list.
  10. Moves the gnome-sc threads to the specified CPUs, CPUs 0 and 1.
  11. Displays the result of the move.

Prerequisites

• The tuna tool is installed. For more information, see Installing tuna tool.

Procedure

• To view the current IRQs and their affinity:

  # tuna --show_irqs
  # users            affinity
  0 timer                   0
  1 i8042                   0
  7 parport0                0

  Copy to Clipboard Toggle word wrap

• To specify the list of IRQs to be affected by a command:

  # tuna --irqs=irq_list [command]

  Copy to Clipboard Toggle word wrap

  The irq_list argument is a list of comma-separated IRQ numbers or user-name patterns.

  Replace [command] with, for example, --spread.

• To move an interrupt to a specified CPU:

  # tuna --irqs=128 --show_irqs
     # users            affinity
   128 iwlwifi           0,1,2,3
  
  # tuna --irqs=128 --cpus=3 --move

  Copy to Clipboard Toggle word wrap

  Replace 128 with the irq_list argument and 3 with the cpu_list argument.

  The cpu_list argument is a list of comma-separated CPU numbers, for example, --cpus=0,2. For more information, see Tuning CPUs using tuna tool.

Verification

• Compare the state of the selected IRQs before and after moving any interrupt to a specified CPU:

  # tuna --irqs=128 --show_irqs
     # users            affinity
   128 iwlwifi                 3

  Copy to Clipboard Toggle word wrap