Buscar
ApoyoConsolaDesarrolladoresIniciar una pruebaContacto

Este contenido no está disponible en el idioma seleccionado.

Chapter 7. Cluster Network Operator in OpenShift Container Platform

download PDF

You can use the Cluster Network Operator (CNO) to deploy and manage cluster network components on an OpenShift Container Platform cluster, including the Container Network Interface (CNI) network plugin selected for the cluster during installation.

7.1. Cluster Network Operator

The Cluster Network Operator implements the network API from the operator.openshift.io API group. The Operator deploys the OVN-Kubernetes network plugin, or the network provider plugin that you selected during cluster installation, by using a daemon set.

Procedure

The Cluster Network Operator is deployed during installation as a Kubernetes Deployment.

  1. Run the following command to view the Deployment status: 

    $ oc get -n openshift-network-operator deployment/network-operator

    Example output

    NAME               READY   UP-TO-DATE   AVAILABLE   AGE
network-operator   1/1     1            1           56m

  2. Run the following command to view the state of the Cluster Network Operator: 

    $ oc get clusteroperator/network

    Example output

    NAME      VERSION   AVAILABLE   PROGRESSING   DEGRADED   SINCE
network   4.16.1     True        False         False      50m

    The following fields provide information about the status of the operator: AVAILABLE, PROGRESSING, and DEGRADED. The AVAILABLE field is True when the Cluster Network Operator reports an available status condition.

7.2. Viewing the cluster network configuration

Every new OpenShift Container Platform installation has a network.config object named cluster.

Procedure

  • Use the oc describe command to view the cluster network configuration: 

    $ oc describe network.config/cluster

    Example output

    Name:         cluster
Namespace:
Labels:       <none>
Annotations:  <none>
API Version:  config.openshift.io/v1
Kind:         Network
Metadata:
  Self Link:           /apis/config.openshift.io/v1/networks/cluster
Spec: 1
  Cluster Network:
    Cidr:         10.128.0.0/14
    Host Prefix:  23
  Network Type:   OpenShiftSDN
  Service Network:
    172.30.0.0/16
Status: 2
  Cluster Network:
    Cidr:               10.128.0.0/14
    Host Prefix:        23
  Cluster Network MTU:  8951
  Network Type:         OpenShiftSDN
  Service Network:
    172.30.0.0/16
Events:  <none>

    1
    The Spec field displays the configured state of the cluster network.
    2
    The Status field displays the current state of the cluster network configuration.

7.3. Viewing Cluster Network Operator status

You can inspect the status and view the details of the Cluster Network Operator using the oc describe command.

Procedure

  • Run the following command to view the status of the Cluster Network Operator: 

    $ oc describe clusteroperators/network

7.4. Enabling IP forwarding globally

From OpenShift Container Platform 4.14 onward, global IP address forwarding is disabled on OVN-Kubernetes based cluster deployments to prevent undesirable effects for cluster administrators with nodes acting as routers. However, in some cases where an administrator expects traffic to be forwarded a new configuration parameter ipForwarding is available to allow forwarding of all IP traffic.

To re-enable IP forwarding for all traffic on OVN-Kubernetes managed interfaces set the gatewayConfig.ipForwarding specification in the Cluster Network Operator to Global following this procedure:

Procedure

  1. Backup the existing network configuration by running the following command: 

    $ oc get network.operator cluster -o yaml > network-config-backup.yaml

  2. Run the following command to modify the existing network configuration: 

    $ oc edit network.operator cluster

    1. Add or update the following block under spec as illustrated in the following example: 

      spec:
  clusterNetwork:
  - cidr: 10.128.0.0/14
    hostPrefix: 23
  serviceNetwork:
  - 172.30.0.0/16
  networkType: OVNKubernetes
  clusterNetworkMTU: 8900
  defaultNetwork:
    ovnKubernetesConfig:
      gatewayConfig:
        ipForwarding: Global
    2. Save and close the file.

  3. After applying the changes, the OpenShift Cluster Network Operator (CNO) applies the update across the cluster. You can monitor the progress by using the following command: 

    $ oc get clusteroperators network

    The status should eventually report as Available, Progressing=False, and Degraded=False.

  4. Alternatively, you can enable IP forwarding globally by running the following command: 

    $ oc patch network.operator cluster -p '{"spec":{"defaultNetwork":{"ovnKubernetesConfig":{"gatewayConfig":{"ipForwarding": "Global"}}}}}
    Note

    The other valid option for this parameter is Restricted in case you want to revert this change. Restricted is the default and with that setting global IP address forwarding is disabled.

7.5. Viewing Cluster Network Operator logs

You can view Cluster Network Operator logs by using the oc logs command.

Procedure

  • Run the following command to view the logs of the Cluster Network Operator: 

    $ oc logs --namespace=openshift-network-operator deployment/network-operator

7.6. Cluster Network Operator configuration

The configuration for the cluster network is specified as part of the Cluster Network Operator (CNO) configuration and stored in a custom resource (CR) object that is named cluster. The CR specifies the fields for the Network API in the operator.openshift.io API group.

The CNO configuration inherits the following fields during cluster installation from the Network API in the Network.config.openshift.io API group:

clusterNetwork
IP address pools from which pod IP addresses are allocated.
serviceNetwork
IP address pool for services.
defaultNetwork.type
Cluster network plugin. OVNKubernetes is the only supported plugin during installation.
Note

After cluster installation, you can only modify the clusterNetwork IP address range. The default network type can only be changed from OpenShift SDN to OVN-Kubernetes through migration.

You can specify the cluster network plugin configuration for your cluster by setting the fields for the defaultNetwork object in the CNO object named cluster.

7.6.1. Cluster Network Operator configuration object

The fields for the Cluster Network Operator (CNO) are described in the following table:

Table 7.1. Cluster Network Operator configuration object
FieldTypeDescription

metadata.name

string

The name of the CNO object. This name is always cluster.

spec.clusterNetwork

array

A list specifying the blocks of IP addresses from which pod IP addresses are allocated and the subnet prefix length assigned to each individual node in the cluster. For example: 

spec:
  clusterNetwork:
  - cidr: 10.128.0.0/19
    hostPrefix: 23
  - cidr: 10.128.32.0/19
    hostPrefix: 23

spec.serviceNetwork

array

A block of IP addresses for services. The OpenShift SDN and OVN-Kubernetes network plugins support only a single IP address block for the service network. For example: 

spec:
  serviceNetwork:
  - 172.30.0.0/14

This value is ready-only and inherited from the Network.config.openshift.io object named cluster during cluster installation.

spec.defaultNetwork

object

Configures the network plugin for the cluster network.

spec.kubeProxyConfig

object

The fields for this object specify the kube-proxy configuration. If you are using the OVN-Kubernetes cluster network plugin, the kube-proxy configuration has no effect.

defaultNetwork object configuration

The values for the defaultNetwork object are defined in the following table:

Table 7.2. defaultNetwork object
FieldTypeDescription

type

string

OVNKubernetes. The Red Hat OpenShift Networking network plugin is selected during installation. This value cannot be changed after cluster installation.

Note

OpenShift Container Platform uses the OVN-Kubernetes network plugin by default. OpenShift SDN is no longer available as an installation choice for new clusters.

ovnKubernetesConfig

object

This object is only valid for the OVN-Kubernetes network plugin.

Configuration for the OpenShift SDN network plugin

The following table describes the configuration fields for the OpenShift SDN network plugin:

Table 7.3. openshiftSDNConfig object
FieldTypeDescription

mode

string

The network isolation mode for OpenShift SDN.

mtu

integer

The maximum transmission unit (MTU) for the VXLAN overlay network. This value is normally configured automatically.

vxlanPort

integer

The port to use for all VXLAN packets. The default value is 4789.

Example OpenShift SDN configuration

defaultNetwork:
  type: OpenShiftSDN
  openshiftSDNConfig:
    mode: NetworkPolicy
    mtu: 1450
    vxlanPort: 4789

Configuration for the OVN-Kubernetes network plugin

The following table describes the configuration fields for the OVN-Kubernetes network plugin:

Table 7.4. ovnKubernetesConfig object
FieldTypeDescription

mtu

integer

The maximum transmission unit (MTU) for the Geneve (Generic Network Virtualization Encapsulation) overlay network. This value is normally configured automatically.

genevePort

integer

The UDP port for the Geneve overlay network.

ipsecConfig

object

An object describing the IPsec mode for the cluster.

ipv4

object

Specifies a configuration object for IPv4 settings.

ipv6

object

Specifies a configuration object for IPv6 settings.

policyAuditConfig

object

Specify a configuration object for customizing network policy audit logging. If unset, the defaults audit log settings are used.

gatewayConfig

object

Optional: Specify a configuration object for customizing how egress traffic is sent to the node gateway.

Note

While migrating egress traffic, you can expect some disruption to workloads and service traffic until the Cluster Network Operator (CNO) successfully rolls out the changes.

Table 7.5. ovnKubernetesConfig.ipv4 object
FieldTypeDescription

internalTransitSwitchSubnet

string

If your existing network infrastructure overlaps with the 100.88.0.0/16 IPv4 subnet, you can specify a different IP address range for internal use by OVN-Kubernetes. The subnet for the distributed transit switch that enables east-west traffic. This subnet cannot overlap with any other subnets used by OVN-Kubernetes or on the host itself. It must be large enough to accommodate one IP address per node in your cluster.

The default value is 100.88.0.0/16.

internalJoinSubnet

string

If your existing network infrastructure overlaps with the 100.64.0.0/16 IPv4 subnet, you can specify a different IP address range for internal use by OVN-Kubernetes. You must ensure that the IP address range does not overlap with any other subnet used by your OpenShift Container Platform installation. The IP address range must be larger than the maximum number of nodes that can be added to the cluster. For example, if the clusterNetwork.cidr value is 10.128.0.0/14 and the clusterNetwork.hostPrefix value is /23, then the maximum number of nodes is 2^(23-14)=512.

The default value is 100.64.0.0/16.

Table 7.6. ovnKubernetesConfig.ipv6 object
FieldTypeDescription

internalTransitSwitchSubnet

string

If your existing network infrastructure overlaps with the fd97::/64 IPv6 subnet, you can specify a different IP address range for internal use by OVN-Kubernetes. The subnet for the distributed transit switch that enables east-west traffic. This subnet cannot overlap with any other subnets used by OVN-Kubernetes or on the host itself. It must be large enough to accommodate one IP address per node in your cluster.

The default value is fd97::/64.

internalJoinSubnet

string

If your existing network infrastructure overlaps with the fd98::/64 IPv6 subnet, you can specify a different IP address range for internal use by OVN-Kubernetes. You must ensure that the IP address range does not overlap with any other subnet used by your OpenShift Container Platform installation. The IP address range must be larger than the maximum number of nodes that can be added to the cluster.

The default value is fd98::/64.

Table 7.7. policyAuditConfig object
FieldTypeDescription

rateLimit

integer

The maximum number of messages to generate every second per node. The default value is 20 messages per second.

maxFileSize

integer

The maximum size for the audit log in bytes. The default value is 50000000 or 50 MB.

maxLogFiles

integer

The maximum number of log files that are retained.

destination

string

One of the following additional audit log targets:

libc
The libc syslog() function of the journald process on the host.
udp:<host>:<port>
A syslog server. Replace <host>:<port> with the host and port of the syslog server.
unix:<file>
A Unix Domain Socket file specified by <file>.
null
Do not send the audit logs to any additional target.

syslogFacility

string

The syslog facility, such as kern, as defined by RFC5424. The default value is local0.

Table 7.8. gatewayConfig object
FieldTypeDescription

routingViaHost

boolean

Set this field to true to send egress traffic from pods to the host networking stack. For highly-specialized installations and applications that rely on manually configured routes in the kernel routing table, you might want to route egress traffic to the host networking stack. By default, egress traffic is processed in OVN to exit the cluster and is not affected by specialized routes in the kernel routing table. The default value is false.

This field has an interaction with the Open vSwitch hardware offloading feature. If you set this field to true, you do not receive the performance benefits of the offloading because egress traffic is processed by the host networking stack.

ipForwarding

object

You can control IP forwarding for all traffic on OVN-Kubernetes managed interfaces by using the ipForwarding specification in the Network resource. Specify Restricted to only allow IP forwarding for Kubernetes related traffic. Specify Global to allow forwarding of all IP traffic. For new installations, the default is Restricted. For updates to OpenShift Container Platform 4.14 or later, the default is Global.

ipv4

object

Optional: Specify an object to configure the internal OVN-Kubernetes masquerade address for host to service traffic for IPv4 addresses.

ipv6

object

Optional: Specify an object to configure the internal OVN-Kubernetes masquerade address for host to service traffic for IPv6 addresses.

Table 7.9. gatewayConfig.ipv4 object
FieldTypeDescription

internalMasqueradeSubnet

string

The masquerade IPv4 addresses that are used internally to enable host to service traffic. The host is configured with these IP addresses as well as the shared gateway bridge interface. The default value is 169.254.169.0/29.

Table 7.10. gatewayConfig.ipv6 object
FieldTypeDescription

internalMasqueradeSubnet

string

The masquerade IPv6 addresses that are used internally to enable host to service traffic. The host is configured with these IP addresses as well as the shared gateway bridge interface. The default value is fd69::/125.

Table 7.11. ipsecConfig object
FieldTypeDescription

mode

string

Specifies the behavior of the IPsec implementation. Must be one of the following values:

  • Disabled: IPsec is not enabled on cluster nodes.
  • External: IPsec is enabled for network traffic with external hosts.
  • Full: IPsec is enabled for pod traffic and network traffic with external hosts.
Note

You can only change the configuration for your cluster network plugin during cluster installation, except for the gatewayConfig field that can be changed at runtime as a postinstallation activity.

Example OVN-Kubernetes configuration with IPSec enabled

defaultNetwork:
  type: OVNKubernetes
  ovnKubernetesConfig:
    mtu: 1400
    genevePort: 6081
      ipsecConfig:
        mode: Full

Important

Using OVNKubernetes can lead to a stack exhaustion problem on IBM Power®.

kubeProxyConfig object configuration (OpenShiftSDN container network interface only)

The values for the kubeProxyConfig object are defined in the following table:

Table 7.12. kubeProxyConfig object
FieldTypeDescription

iptablesSyncPeriod

string

The refresh period for iptables rules. The default value is 30s. Valid suffixes include s, m, and h and are described in the Go time package documentation.

Note

Because of performance improvements introduced in OpenShift Container Platform 4.3 and greater, adjusting the iptablesSyncPeriod parameter is no longer necessary.

proxyArguments.iptables-min-sync-period

array

The minimum duration before refreshing iptables rules. This field ensures that the refresh does not happen too frequently. Valid suffixes include s, m, and h and are described in the Go time package. The default value is: 

kubeProxyConfig:
  proxyArguments:
    iptables-min-sync-period:
    - 0s

7.6.2. Cluster Network Operator example configuration

A complete CNO configuration is specified in the following example:

Example Cluster Network Operator object

apiVersion: operator.openshift.io/v1
kind: Network
metadata:
  name: cluster
spec:
  clusterNetwork:
  - cidr: 10.128.0.0/14
    hostPrefix: 23
  serviceNetwork:
  - 172.30.0.0/16
  networkType: OVNKubernetes
      clusterNetworkMTU: 8900

7.7. Additional resources

Red Hat logoGithubRedditYoutubeTwitter

Aprender

Pruebe, compre y venda

Comunidades

Acerca de la documentación de Red Hat

Ayudamos a los usuarios de Red Hat a innovar y alcanzar sus objetivos con nuestros productos y servicios con contenido en el que pueden confiar.

Hacer que el código abierto sea más inclusivo

Red Hat se compromete a reemplazar el lenguaje problemático en nuestro código, documentación y propiedades web. Para más detalles, consulte el Blog de Red Hat.

Acerca de Red Hat

Ofrecemos soluciones reforzadas que facilitan a las empresas trabajar en plataformas y entornos, desde el centro de datos central hasta el perímetro de la red.

© 2024 Red Hat, Inc.