Red Hat Summit Red Hat SummitApoyoConsolaDesarrolladoresIniciar una pruebaContacto

Este contenido no está disponible en el idioma seleccionado.

10.9. Example - Setting up Cascading Geo-replication

This section provides step by step instructions to set up a cascading geo-replication session. The configuration of this example has three volumes and the volume names are master-vol, interimmaster-vol, and slave-vol.
  1. Verify that your environment matches the minimum system requirements listed in Section 10.3.3, “Prerequisites”.
  2. Determine the appropriate deployment scenario. For more information on deployment scenarios, see Section 10.3.1, “Exploring Geo-replication Deployment Scenarios”.
  3. Configure the environment and create a geo-replication session between master-vol and interimmaster-vol.
    1. Create a common pem pub file, run the following command on the master node where the passwordless SSH connection is configured: 
      # gluster system:: execute gsec_create
      Copy to Clipboard Toggle word wrap
    2. Create the geo-replication session using the following command. The push-pem option is needed to perform the necessary pem-file setup on the interimmaster nodes. 
      # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol create
push-pem
      Copy to Clipboard Toggle word wrap
    3. Verify the status of the created session by running the following command: 
      # gluster volume geo-replication master-vol interimhost::interimmaster-vol status
      Copy to Clipboard Toggle word wrap
  4. Configure the meta-volume for geo-replication: 
    # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For more information on configuring meta-volume, see Section 10.3.5, “Configuring a Meta-Volume”.
  5. Start a Geo-replication session between the hosts: 
    # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol start
    Copy to Clipboard Toggle word wrap
    This command will start distributed geo-replication on all the nodes that are part of the master volume. If a node that is part of the master volume is down, the command will still be successful. In a replica pair, the geo-replication session will be active on any of the replica nodes, but remain passive on the others. After executing the command, it may take a few minutes for the session to initialize and become stable.
  6. Verifying the status of geo-replication session by running the following command: 
    # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol status
    Copy to Clipboard Toggle word wrap
  7. Create a geo-replication session between interimmaster-vol and slave-vol.
    1. Create a common pem pub file by running the following command on the interimmaster master node where the passwordless SSH connection is configured: 
      # gluster system:: execute gsec_create
      Copy to Clipboard Toggle word wrap
    2. On interimmaster node, create the geo-replication session using the following command. The push-pem option is needed to perform the necessary pem-file setup on the slave nodes. 
      # gluster volume geo-replication interimmaster-vol slave_host.com::slave-vol create push-pem
      Copy to Clipboard Toggle word wrap
    3. Verify the status of the created session by running the following command: 
      # gluster volume geo-replication interrimmaster-vol slave_host::slave-vol status
      Copy to Clipboard Toggle word wrap
  8. Configure the meta-volume for geo-replication: 
    # gluster volume geo-replication interrimmaster-vol slave_host::slave-vol config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For more information on configuring meta-volume, see Section 10.3.5, “Configuring a Meta-Volume”.
  9. Start a geo-replication session between interrimaster-vol and slave-vol by running the following command: 
    # gluster volume geo-replication interrimmaster-vol slave_host.com::slave-vol start
    Copy to Clipboard Toggle word wrap
  10. Verify the status of geo-replication session by running the following: 
    # gluster volume geo-replication interrimmaster-vol slave_host.com::slave-vol status
    Copy to Clipboard Toggle word wrap
Volver arriba
Red Hat logoGithubredditYoutubeTwitter

Aprender

Pruebe, compre y venda

Comunidades

Acerca de la documentación de Red Hat

Ayudamos a los usuarios de Red Hat a innovar y alcanzar sus objetivos con nuestros productos y servicios con contenido en el que pueden confiar. Explore nuestras recientes actualizaciones.

Hacer que el código abierto sea más inclusivo

Red Hat se compromete a reemplazar el lenguaje problemático en nuestro código, documentación y propiedades web. Para más detalles, consulte el Blog de Red Hat.

Acerca de Red Hat

Ofrecemos soluciones reforzadas que facilitan a las empresas trabajar en plataformas y entornos, desde el centro de datos central hasta el perímetro de la red.

Theme

© 2025 Red Hat