Red Hat Summit Red Hat SummitApoyoConsolaDesarrolladoresIniciar una pruebaContacto

Este contenido no está disponible en el idioma seleccionado.

Chapter 20. Automatically discovering bare metal nodes

You can use auto-discovery to register overcloud nodes and generate their metadata, without the need to create an instackenv.json file. This improvement can help to reduce the time it takes to collect information about a node. For example, if you use auto-discovery, you do not to collate the IPMI IP addresses and subsequently create the instackenv.json.

20.1. Prerequisites
Copiar enlace

  • You have configured all overcloud nodes BMCs to be accessible to director through the IPMI.
  • You have configured all overcloud nodes to PXE boot from the NIC that is connected to the undercloud control plane network.

20.2. Enabling auto-discovery
Copiar enlace

  1. Enable Bare Metal auto-discovery in the undercloud.conf file: 

    enable_node_discovery = True
discovery_default_driver = ipmi
    Copy to Clipboard Toggle word wrap
    • enable_node_discovery - When enabled, any node that boots the introspection ramdisk using PXE is enrolled in the Bare Metal service (ironic) automatically.
    • discovery_default_driver - Sets the driver to use for discovered nodes. For example, ipmi.

  2. Add your IPMI credentials to ironic:

    1. Add your IPMI credentials to a file named ipmi-credentials.json. Replace the SampleUsername, RedactedSecurePassword, and bmc_address values in this example to suit your environment: 

      [
    {
        "description": "Set default IPMI credentials",
        "conditions": [
            {"op": "eq", "field": "data://auto_discovered", "value": true}
        ],
        "actions": [
            {"action": "set-attribute", "path": "driver_info/ipmi_username",
             "value": "SampleUsername"},
            {"action": "set-attribute", "path": "driver_info/ipmi_password",
             "value": "RedactedSecurePassword"},
            {"action": "set-attribute", "path": "driver_info/ipmi_address",
             "value": "{data[inventory][bmc_address]}"}
        ]
    }
]
      Copy to Clipboard Toggle word wrap

  3. Import the IPMI credentials file into ironic: 

    $ openstack baremetal introspection rule import ipmi-credentials.json
    Copy to Clipboard Toggle word wrap

20.3. Testing auto-discovery
Copiar enlace

  1. Power on the required nodes.

  2. Run the openstack baremetal node list command. You should see the new nodes listed in an enrolled state: 

    $ openstack baremetal node list
+--------------------------------------+------+---------------+-------------+--------------------+-------------+
| UUID                                 | Name | Instance UUID | Power State | Provisioning State | Maintenance |
+--------------------------------------+------+---------------+-------------+--------------------+-------------+
| c6e63aec-e5ba-4d63-8d37-bd57628258e8 | None | None          | power off   | enroll             | False       |
| 0362b7b2-5b9c-4113-92e1-0b34a2535d9b | None | None          | power off   | enroll             | False       |
+--------------------------------------+------+---------------+-------------+--------------------+-------------+
    Copy to Clipboard Toggle word wrap

  3. Set the resource class for each node: 

    $ for NODE in `openstack baremetal node list -c UUID -f value` ; do openstack baremetal node set $NODE --resource-class baremetal ; done
    Copy to Clipboard Toggle word wrap

  4. Configure the kernel and ramdisk for each node: 

    $ for NODE in `openstack baremetal node list -c UUID -f value` ; do openstack baremetal node manage $NODE ; done
$ openstack overcloud node configure --all-manageable
    Copy to Clipboard Toggle word wrap

  5. Set all nodes to available: 

    $ for NODE in `openstack baremetal node list -c UUID -f value` ; do openstack baremetal node provide $NODE ; done
    Copy to Clipboard Toggle word wrap

20.4. Using rules to discover different vendor hardware
Copiar enlace

If you have a heterogeneous hardware environment, you can use introspection rules to assign credentials and remote management credentials. For example, you might want a separate discovery rule to handle your Dell nodes that use DRAC:

  1. Create a file named dell-drac-rules.json with the following contents: 

    [
    {
        "description": "Set default IPMI credentials",
        "conditions": [
            {"op": "eq", "field": "data://auto_discovered", "value": true},
            {"op": "ne", "field": "data://inventory.system_vendor.manufacturer",
             "value": "Dell Inc."}
        ],
        "actions": [
            {"action": "set-attribute", "path": "driver_info/ipmi_username",
             "value": "SampleUsername"},
            {"action": "set-attribute", "path": "driver_info/ipmi_password",
             "value": "RedactedSecurePassword"},
            {"action": "set-attribute", "path": "driver_info/ipmi_address",
             "value": "{data[inventory][bmc_address]}"}
        ]
    },
    {
        "description": "Set the vendor driver for Dell hardware",
        "conditions": [
            {"op": "eq", "field": "data://auto_discovered", "value": true},
            {"op": "eq", "field": "data://inventory.system_vendor.manufacturer",
             "value": "Dell Inc."}
        ],
        "actions": [
            {"action": "set-attribute", "path": "driver", "value": "idrac"},
            {"action": "set-attribute", "path": "driver_info/drac_username",
             "value": "SampleUsername"},
            {"action": "set-attribute", "path": "driver_info/drac_password",
             "value": "RedactedSecurePassword"},
            {"action": "set-attribute", "path": "driver_info/drac_address",
             "value": "{data[inventory][bmc_address]}"}
        ]
    }
]
    Copy to Clipboard Toggle word wrap

    Replace the user name and password values in this example to suit your environment:

  2. Import the rule into ironic: 

    $ openstack baremetal introspection rule import dell-drac-rules.json
    Copy to Clipboard Toggle word wrap
Volver arriba
Red Hat logoGithubredditYoutubeTwitter

Aprender

Pruebe, compre y venda

Comunidades

Acerca de la documentación de Red Hat

Ayudamos a los usuarios de Red Hat a innovar y alcanzar sus objetivos con nuestros productos y servicios con contenido en el que pueden confiar. Explore nuestras recientes actualizaciones.

Hacer que el código abierto sea más inclusivo

Red Hat se compromete a reemplazar el lenguaje problemático en nuestro código, documentación y propiedades web. Para más detalles, consulte el Blog de Red Hat.

Acerca de Red Hat

Ofrecemos soluciones reforzadas que facilitan a las empresas trabajar en plataformas y entornos, desde el centro de datos central hasta el perímetro de la red.

Theme

© 2025 Red Hat