Ce contenu n'est pas disponible dans la langue sélectionnée.

Chapter 2. Ceph network configuration

As a storage administrator, you must understand the network environment that the Red Hat Ceph Storage cluster will operate in, and configure the Red Hat Ceph Storage accordingly. Understanding and configuring the Ceph network options will ensure optimal performance and reliability of the overall storage cluster.

Prerequisites

Network connectivity.
Installation of the Red Hat Ceph Storage software.

2.1. Network configuration for Ceph

Network configuration is critical for building a high performance Red Hat Ceph Storage cluster. The Ceph storage cluster does not perform request routing or dispatching on behalf of the Ceph client. Instead, Ceph clients make requests directly to Ceph OSD daemons. Ceph OSDs perform data replication on behalf of Ceph clients, which means replication and other factors impose additional loads on the networks of Ceph storage clusters.

Ceph has one network configuration requirement that applies to all daemons. The Ceph configuration file must specify the host for each daemon.

Some deployment utilities, such as cephadm creates a configuration file for you. Do not set these values if the deployment utility does it for you.

Important

The host option is the short name of the node, not its FQDN. It is not an IP address.

All Ceph clusters must use a public network. However, unless you specify an internal cluster network, Ceph assumes a single public network. Ceph can function with a public network only, but for large storage clusters, you will see significant performance improvement with a second private network for carrying only cluster-related traffic.

Important

Red Hat recommends running a Ceph storage cluster with two networks. One public network and one private network.

To support two networks, each Ceph Node will need to have more than one network interface card (NIC).

There are several reasons to consider operating two separate networks:

Performance: Ceph OSDs handle data replication for the Ceph clients. When Ceph OSDs replicate data more than once, the network load between Ceph OSDs easily dwarfs the network load between Ceph clients and the Ceph storage cluster. This can introduce latency and create a performance problem. Recovery and rebalancing can also introduce significant latency on the public network.
Security: While most people are generally civil, some actors will engage in what is known as a Denial of Service (DoS) attack. When traffic between Ceph OSDs gets disrupted, peering may fail and placement groups may no longer reflect an active + clean state, which may prevent users from reading and writing data. A great way to defeat this type of attack is to maintain a completely separate cluster network that does not connect directly to the internet.

Network configuration settings are not required. Ceph can function with a public network only, assuming a public network is configured on all hosts running a Ceph daemon. However, Ceph allows you to establish much more specific criteria, including multiple IP networks and subnet masks for your public network. You can also establish a separate cluster network to handle OSD heartbeat, object replication, and recovery traffic.

Do not confuse the IP addresses you set in the configuration with the public-facing IP addresses network clients might use to access your service. Typical internal IP networks are often 192.168.0.0 or 10.0.0.0.

Note

Ceph uses CIDR notation for subnets, for example, 10.0.0.0/24.

Important

If you specify more than one IP address and subnet mask for either the public or the private network, the subnets within the network must be capable of routing to each other. Additionally, make sure you include each IP address and subnet in your IP tables and open ports for them as necessary.

When you configured the networks, you can restart the cluster or restart each daemon. Ceph daemons bind dynamically, so you do not have to restart the entire cluster at once if you change the network configuration.

Additional Resources

See the common options in Red Hat Ceph Storage Configuration Guide, Appendix B for specific option descriptions and usage.

2.2. Ceph network messenger

Messenger is the Ceph network layer implementation. Red Hat supports two messenger types:

simple
async

In Red Hat Ceph Storage 7 and higher, async is the default messenger type. To change the messenger type, specify the ms_type configuration setting in the [global] section of the Ceph configuration file.

Note

For the async messenger, Red Hat supports the posix transport type, but does not currently support rdma or dpdk. By default, the ms_type setting in Red Hat Ceph Storage reflects async+posix, where async is the messenger type and posix is the transport type.

SimpleMessenger

The SimpleMessenger implementation uses TCP sockets with two threads per socket. Ceph associates each logical session with a connection. A pipe handles the connection, including the input and output of each message. While SimpleMessenger is effective for the posix transport type, it is not effective for other transport types such as rdma or dpdk.

AsyncMessenger

Consequently, AsyncMessenger is the default messenger type for Red Hat Ceph Storage 7 or higher. For Red Hat Ceph Storage 7 or higher, the AsyncMessenger implementation uses TCP sockets with a fixed-size thread pool for connections, which should be equal to the highest number of replicas or erasure-code chunks. The thread count can be set to a lower value if performance degrades due to a low CPU count or a high number of OSDs per server.

Note

Red Hat does not support other transport types such as rdma or dpdk at this time.

Additional Resources

See the AsyncMessenger options in Red Hat Ceph Storage Configuration Guide, Appendix B for specific option descriptions and usage.
See the Red Hat Ceph Storage Architecture Guide for details about using on-wire encryption with the Ceph messenger version 2 protocol.

2.3. Configuring a public network

To configure Ceph networks, use the config set command within the cephadm shell. Note that the IP addresses you set in your network configuration are different from the public-facing IP addresses that network clients might use to access your service.

Ceph functions perfectly well with only a public network. However, Ceph allows you to establish much more specific criteria, including multiple IP networks for your public network.

You can also establish a separate, private cluster network to handle OSD heartbeat, object replication, and recovery traffic. For more information about the private network, see Configuring a private network.

Note

Ceph uses CIDR notation for subnets, for example, 10.0.0.0/24. Typical internal IP networks are often 192.168.0.0/24 or 10.0.0.0/24.

Note

If you specify more than one IP address for either the public or the cluster network, the subnets within the network must be capable of routing to each other. In addition, make sure you include each IP address in your IP tables, and open ports for them as necessary.

The public network configuration allows you specifically define IP addresses and subnets for the public network.

Prerequisites

Installation of the Red Hat Ceph Storage software.

Procedure

Configure the public network with the subnet:

Syntax

ceph config set mon public_network IP_ADDRESS_WITH_SUBNET

Example

[ceph: root@host01 /]# ceph config set mon public_network 192.168.0.0/24

Get the list of services in the storage cluster:
Example
```
[ceph: root@host01 /]# ceph orch ls
```
Restart the daemons. Ceph daemons bind dynamically, so you do not have to restart the entire cluster at once if you change the network configuration for a specific daemon.
Example
```
[ceph: root@host01 /]# ceph orch restart mon
```

Optional: If you want to restart the cluster, on the admin node as a root user, run systemctl command:

Syntax

systemctl restart ceph-FSID_OF_CLUSTER.target

Example

[root@host01 ~]# systemctl restart ceph-1ca9f6a8-d036-11ec-8263-fa163ee967ad.target

Additional Resources

See the common options in Red Hat Ceph Storage Configuration Guide, Appendix B for specific option descriptions and usage.

2.4. Configuring a private network

Network configuration settings are not required. Ceph assumes a public network with all hosts operating on it, unless you specifically configure a cluster network, also known as a private network.

If you create a cluster network, OSDs routes heartbeat, object replication, and recovery traffic over the cluster network. This can improve performance, compared to using a single network.

Important

For added security, the cluster network should not be reachable from the public network or the Internet.

To assign a cluster network, use the --cluster-network option with the cephadm bootstrap command. The cluster network that you specify must define a subnet in CIDR notation (for example, 10.90.90.0/24 or fe80::/64).

You can also configure the cluster_network after boostrap.

Prerequisites

Access to the Ceph software repository.
Root-level access to all nodes in the storage cluster.

Procedure

Run the cephadm bootstrap command from the initial node that you want to use as the Monitor node in the storage cluster. Include the --cluster-network option in the command.

Syntax

cephadm bootstrap --mon-ip IP-ADDRESS --registry-url registry.redhat.io --registry-username USER_NAME --registry-password PASSWORD --cluster-network NETWORK-IP-ADDRESS

Example

[root@host01 ~]# cephadm bootstrap --mon-ip 10.10.128.68 --registry-url registry.redhat.io --registry-username myuser1 --registry-password mypassword1 --cluster-network 10.10.0.0/24

To configure the cluster_network after bootstrap, run the config set command and redeploy the daemons:
1. Log in to the cephadm shell:
  Example
```
[root@host01 ~]# cephadm shell
```
2. Configure the cluster network with the subnet:
  Syntax
```
ceph config set global cluster_network IP_ADDRESS_WITH_SUBNET
```
  Example
```
[ceph: root@host01 /]# ceph config set global cluster_network 10.10.0.0/24
```
3. Get the list of services in the storage cluster:
  Example
```
[ceph: root@host01 /]# ceph orch ls
```
4. Restart the daemons. Ceph daemons bind dynamically, so you do not have to restart the entire cluster at once if you change the network configuration for a specific daemon.
  Example
```
[ceph: root@host01 /]# ceph orch restart mon
```
5. Optional: If you want to restart the cluster, on the admin node as a root user, run systemctl command:
  Syntax
```
systemctl restart ceph-FSID_OF_CLUSTER.target
```
  Example
```
[root@host01 ~]# systemctl restart ceph-1ca9f6a8-d036-11ec-8263-fa163ee967ad.target
```

Additional Resources

For more information about invoking cephadm bootstrap, see the Bootstrapping a new storage cluster section in the Red Hat Ceph Storage Installation Guide.

2.5. Configuring multiple public networks to the cluster

When the user wants to place the Ceph Monitor daemons on hosts belonging to multiple network subnets, configuring multiple public networks to the cluster is necessary. An example of usage is a stretch cluster mode used for Advanced Cluster Management (ACM) in Metro DR for OpenShift Data Foundation.

You can configure multiple public networks to the cluster during bootstrap and once bootstrap is complete.

Prerequisites

Before adding a host be sure that you have a running Red Hat Ceph Storage cluster.

Procedure

Bootstrap a Ceph cluster configured with multiple public networks.
1. Prepare a ceph.conf file containing a mon public network section:
  Important
  At least one of the provided public networks must be configured on the current host used for bootstrap.
  Syntax
```
[mon]
public_network = PUBLIC_NETWORK1, PUBLIC_NETWORK2
```
  Example
```
[mon]
public_network = 10.40.0.0/24, 10.41.0.0/24, 10.42.0.0/24
```
  This is an example with three public networks to be provided for bootstrap.
2. Bootstrap the cluster by providing the ceph.conf file as input:
  Note
  During the bootstrap you can include any other arguments that you want to provide.
  Syntax
```
cephadm --image IMAGE_URL bootstrap --mon-ip MONITOR_IP -c PATH_TO_CEPH_CONF
```
  Note
  Alternatively, an IMAGE_ID (such as, 13ea90216d0be03003d12d7869f72ad9de5cec9e54a27fd308e01e467c0d4a0a) can be used instead of IMAGE_URL.
  Example
```
[root@host01 ~]# cephadm –image cp.icr.io/cp/ibm-ceph/ceph-5-rhel8:latest bootstrap –mon-ip 10.40.0.0/24 -c /etc/ceph/ceph.conf
```
Add new hosts to the subnets:
Note
The host being added must be reachable from the host that the active manager is running on.
1. Install the cluster’s public SSH key in the new host’s root user’s authorized_keys file:
  Syntax
```
ssh-copy-id -f -i /etc/ceph/ceph.pub root@NEW_HOST
```
  Example
```
[root@host01 ~]# ssh-copy-id -f -i /etc/ceph/ceph.pub root@host02
[root@host01 ~]# ssh-copy-id -f -i /etc/ceph/ceph.pub root@host03
```
2. Log into cephadm shell:
  Example
```
[root@host01 ~]# cephadm shell
```
3. Add the new host to the Ceph cluster:
  Syntax
```
ceph orch host add NEW_HOST IP [LABEL1 ...]
```
  Example
```
[root@host01 ~]# ceph orch host add host02 10.10.0.102 label1
[root@host01 ~]# ceph orch host add host03 10.10.0.103 label2
```
  Note
  It is best to explicitly provide the host IP address. If an IP is not provided, then the host name is immediately resolved via DNS and that IP is used.
  One or more labels can also be included to immediately label the new host. For example, by default the _admin label makes cephadm maintain a copy of the ceph.conf file and a client.admin keyring file in /etc/ceph directory.
Add the networks configurations for the public network parameters to a running cluster. Be sure that the subnets are separated by commas and that the subnets are listed in subnet/mask format.
Syntax
```
ceph config set mon public_network "SUBNET_1,SUBNET_2, ..."
```
Example
```
[root@host01 ~]# ceph config set mon public_network "192.168.0.0/24, 10.42.0.0/24, ..."
```
If necessary, update the mon specifications to place the mon daemons on hosts within the specified subnets.

Additional Resources

See Adding hosts for more details about adding hosts in the Red Hat Ceph Storage Installation Guide.
See Stretch clusters for Ceph storage for more details about stretch clusters in the Red Hat Ceph Storage Administration Guide.

2.6. Verifying firewall rules are configured for default Ceph ports

By default, Red Hat Ceph Storage daemons use TCP ports 6800—7100 to communicate with other hosts in the cluster. You can verify that the host’s firewall allows connection on these ports.

Note

If your network has a dedicated firewall, you might need to verify its configuration in addition to following this procedure. See the firewall’s documentation for more information.

See the firewall’s documentation for more information.

Prerequisites

Root-level access to the host.

Procedure

Verify the host’s iptables configuration:
1. List active rules:
```
[root@host1 ~]# iptables -L
```
2. Verify the absence of rules that restrict connectivity on TCP ports 6800—7100.
  Example
```
REJECT all -- anywhere anywhere reject-with icmp-host-prohibited
```
Verify the host’s firewalld configuration:
1. List ports open on the host:
  Syntax
```
firewall-cmd --zone ZONE --list-ports
```
  Example
```
[root@host1 ~]# firewall-cmd --zone default --list-ports
```
2. Verify the range is inclusive of TCP ports 6800—7100.

2.7. Firewall settings for Ceph Monitor node

You can enable encryption for all Ceph traffic over the network with the introduction of the messenger version 2 protocol. The secure mode setting for messenger v2 encrypts communication between Ceph daemons and Ceph clients, giving you end-to-end encryption.

Messenger v2 Protocol

The second version of Ceph’s on-wire protocol, msgr2, includes several new features:

A secure mode encrypts all data moving through the network.
Encapsulation improvement of authentication payloads.
Improvements to feature advertisement and negotiation.

The Ceph daemons bind to multiple ports allowing both the legacy, v1-compatible, and the new, v2-compatible, Ceph clients to connect to the same storage cluster. Ceph clients or other Ceph daemons connecting to the Ceph Monitor daemon will try to use the v2 protocol first, if possible, but if not, then the legacy v1 protocol will be used. By default, both messenger protocols, v1 and v2, are enabled. The new v2 port is 3300, and the legacy v1 port is 6789, by default.

Prerequisites

A running Red Hat Ceph Storage cluster.
Access to the Ceph software repository.
Root-level access to the Ceph Monitor node.

Procedure

Add rules using the following example:
```
[root@mon ~]# sudo iptables -A INPUT -i IFACE -p tcp -s IP-ADDRESS/NETMASK --dport 6789 -j ACCEPT
[root@mon ~]# sudo iptables -A INPUT -i IFACE -p tcp -s IP-ADDRESS/NETMASK --dport 3300 -j ACCEPT
```
1. Replace IFACE with the public network interface (for example, eth0, eth1, and so on).
2. Replace IP-ADDRESS with the IP address of the public network and NETMASK with the netmask for the public network.

For the firewalld daemon, execute the following commands:

[root@mon ~]# firewall-cmd --zone=public --add-port=6789/tcp
[root@mon ~]# firewall-cmd --zone=public --add-port=6789/tcp --permanent
[root@mon ~]# firewall-cmd --zone=public --add-port=3300/tcp
[root@mon ~]# firewall-cmd --zone=public --add-port=3300/tcp --permanent

Additional resources

See the Red Hat Ceph Storage network configuration options in Ceph network configuration options for specific option descriptions and usage.
See the Red Hat Ceph Storage Architecture Guide for details about using Ceph on-wire encryption with the Ceph messenger version 2 protocol.

Ce contenu n'est pas disponible dans la langue sélectionnée.

Chapter 2. Ceph network configuration

2.1. Network configuration for Ceph

2.2. Ceph network messenger

2.3. Configuring a public network

2.4. Configuring a private network

2.5. Configuring multiple public networks to the cluster

2.6. Verifying firewall rules are configured for default Ceph ports

2.7. Firewall settings for Ceph Monitor node

Apprendre

Essayez, achetez et vendez

Communautés

À propos de la documentation Red Hat

Rendre l’open source plus inclusif

À propos de Red Hat

Red Hat legal and privacy links

Red Hat legal and privacy links