Red Hat Summit Red Hat SummitSupportConsoleDéveloppeursCommencer un essaiContact

Ce contenu n'est pas disponible dans la langue sélectionnée.

Chapter 11. Setting container network modes

The chapter provides information about how to set different network modes.

11.1. Running containers with a static IP
Copier lien

The podman run command with the --ip option sets the container network interface to a particular IP address (for example, 10.88.0.44). To verify that you set the IP address correctly, run the podman inspect command.

Prerequisites

  • The container-tools meta-package is installed.

Procedure

  • Set the container network interface to the IP address 10.88.0.44: 

    # podman run -d --name=myubi --ip=10.88.0.44 registry.access.redhat.com/ubi9/ubi
efde5f0a8c723f70dd5cb5dc3d5039df3b962fae65575b08662e0d5b5f9fbe85
    Copy to Clipboard Toggle word wrap

Verification

  • Check that the IP address is set properly: 

    # podman inspect --format='{{.NetworkSettings.IPAddress}}' myubi
10.88.0.44
    Copy to Clipboard Toggle word wrap

11.2. Running the DHCP plugin for Netavark using systemd
Copier lien

Prerequisites

  • The container-tools meta-package is installed.

Procedure

  1. Enable the DHCP proxy by using the systemd socket: 

    systemctl enable --now netavark-dhcp-proxy.socket
Created symlink /etc/systemd/system/sockets.target.wants/netavark-dhcp-proxy.socket  /usr/lib/systemd/system/netavark-dhcp-proxy.socket.
    Copy to Clipboard Toggle word wrap

  2. Optional: Display the socket unit file: 

    # cat /usr/lib/systemd/system/netavark-dhcp-proxy.socket
[Unit]
Description=Netavark DHCP proxy socket

[Socket]
ListenStream=%t/podman/nv-proxy.sock
SocketMode=0660

[Install]
WantedBy=sockets.target
    Copy to Clipboard Toggle word wrap

  3. Create a macvlan network and specify your host interface with it. Typically, it is your external interface: 

    # podman network create -d macvlan --interface-name <LAN_INTERFACE> mv1
mv1
    Copy to Clipboard Toggle word wrap

  4. Run the container by using newly created network: 

    # podman run --rm --network mv1 -d --name test alpine top
894ae3b6b1081aca2a5d90a9855568eaa533c08a174874be59569d4656f9bc45
    Copy to Clipboard Toggle word wrap

Verification

  1. Confirm the container has an IP on your local subnet: 

    # podman exec test ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
    link/ether 5a:30:72:bf:13:76 brd ff:ff:ff:ff:ff:ff
    inet 192.168.188.36/24 brd 192.168.188.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::5830:72ff:febf:1376/64 scope link
       valid_lft forever preferred_lft forever
    Copy to Clipboard Toggle word wrap

  2. Inspect the container to verify it uses correct IP addresses: 

    # podman container inspect test --format {{.NetworkSettings.Networks.mv1.IPAddress}}
192.168.188.36
    Copy to Clipboard Toggle word wrap
Note

When attempting to connect to this IP address, ensure the connection is made from a different host. Connections from the same host are not supported when using macvlan networking.

11.3. The macvlan plugin
Copier lien

Most of the container images do not have a DHCP client, the dhcp plugin acts as a proxy DHCP client for the containers to interact with a DHCP server.

The host system does not have network access to the container. To allow network connections from outside the host to the container, the container has to have an IP on the same network as the host. The macvlan plugin enables you to connect a container to the same network as the host.

Note

This procedure only applies to rootfull containers. Rootless containers are not able to use the macvlan and dhcp plugins.

Note

You can create a macvlan network using the podman network create --driver=macvlan command.

Retour au début
Red Hat logoGithubredditYoutubeTwitter

Apprendre

Essayez, achetez et vendez

Communautés

À propos de la documentation Red Hat

Nous aidons les utilisateurs de Red Hat à innover et à atteindre leurs objectifs grâce à nos produits et services avec un contenu auquel ils peuvent faire confiance. Découvrez nos récentes mises à jour.

Rendre l’open source plus inclusif

Red Hat s'engage à remplacer le langage problématique dans notre code, notre documentation et nos propriétés Web. Pour plus de détails, consultez le Blog Red Hat.

À propos de Red Hat

Nous proposons des solutions renforcées qui facilitent le travail des entreprises sur plusieurs plates-formes et environnements, du centre de données central à la périphérie du réseau.

Theme

© 2025 Red Hat