Questo contenuto non è disponibile nella lingua selezionata.

Chapter 14. Cephadm troubleshooting


As a storage administrator, you can troubleshoot the Red Hat Ceph Storage cluster. Sometimes there is a need to investigate why a Cephadm command failed or why a specific service does not run properly.

14.1. Pause or disable cephadm

If Cephadm does not behave as expected, you can pause most of the background activity with the following command:

Example

[ceph: root@host01 /]# ceph orch pause

This stops any changes, but Cephadm periodically checks hosts to refresh it’s inventory of daemons and devices.

If you want to disable Cephadm completely, run the following commands:

Example

[ceph: root@host01 /]# ceph orch set backend ''
[ceph: root@host01 /]# ceph mgr module disable cephadm

Note that previously deployed daemon containers continue to exist and start as they did before.

To re-enable Cephadm in the cluster, run the following commands:

Example

[ceph: root@host01 /]# ceph mgr module enable cephadm
[ceph: root@host01 /]# ceph orch set backend cephadm

14.2. Per service and per daemon event

Cephadm stores events per service and per daemon in order to aid in debugging failed daemon deployments. These events often contain relevant information:

Per service

Syntax

ceph orch ls --service_name SERVICE_NAME --format yaml

Example

[ceph: root@host01 /]# ceph orch ls --service_name alertmanager --format yaml
service_type: alertmanager
service_name: alertmanager
placement:
  hosts:
  - unknown_host
status:
  ...
  running: 1
  size: 1
events:
- 2021-02-01T08:58:02.741162 service:alertmanager [INFO] "service was created"
- '2021-02-01T12:09:25.264584 service:alertmanager [ERROR] "Failed to apply: Cannot
  place <AlertManagerSpec for service_name=alertmanager> on unknown_host: Unknown hosts"'

Per daemon

Syntax

ceph orch ps --service-name SERVICE_NAME --daemon-id DAEMON_ID --format yaml

Example

[ceph: root@host01 /]# ceph orch ps --service-name mds --daemon-id cephfs.hostname.ppdhsz --format yaml
daemon_type: mds
daemon_id: cephfs.hostname.ppdhsz
hostname: hostname
status_desc: running
...
events:
- 2021-02-01T08:59:43.845866 daemon:mds.cephfs.hostname.ppdhsz [INFO] "Reconfigured
  mds.cephfs.hostname.ppdhsz on host 'hostname'"

14.3. Check cephadm logs

You can monitor the Cephadm log in real time with the following command:

Example

[ceph: root@host01 /]# ceph -W cephadm

You can see the last few messages with the following command:

Example

[ceph: root@host01 /]# ceph log last cephadm

If you have enabled logging to files, you can see a Cephadm log file called ceph.cephadm.log on the monitor hosts.

14.4. Gather log files

You can use the journalctl command, to gather the log files for all the daemons.

Note

You have to run all these commands outside the cephadm shell.

Note

By default, Cephadm stores logs in journald which means that daemon logs are no longer available in /var/log/ceph.

  • To read the log file of a specific daemon, run the following command:

    Syntax

    cephadm logs --name DAEMON_NAME

    Example

    [root@host01 ~]# cephadm logs --name cephfs.hostname.ppdhsz

Note

This command works when run on the same hosts where the daemon is running.

  • To read the log file of a specific daemon running on a different host, run the following command:

    Syntax

    cephadm logs --fsid FSID --name DAEMON_NAME

    Example

    [root@host01 ~]# cephadm logs --fsid 2d2fd136-6df1-11ea-ae74-002590e526e8 --name cephfs.hostname.ppdhsz

    where fsid is the cluster ID provided by the ceph status command.

  • To fetch all log files of all the daemons on a given host, run the following command:

    Syntax

    for name in $(cephadm ls | python3 -c "import sys, json; [print(i['name']) for i in json.load(sys.stdin)]") ; do cephadm logs --fsid FSID_OF_CLUSTER --name "$name" > $name; done

    Example

    [root@host01 ~]# for name in $(cephadm ls | python3 -c "import sys, json; [print(i['name']) for i in json.load(sys.stdin)]") ; do cephadm logs --fsid 57bddb48-ee04-11eb-9962-001a4a000672 --name "$name" > $name; done

14.5. Collect systemd status

  • To print the state of a systemd unit, run the following command:

    Example

    [root@host01 ~]$ systemctl status ceph-a538d494-fb2a-48e4-82c8-b91c37bb0684@mon.host01.service

14.6. List all downloaded container images

To list all the container images that are downloaded on a host, run the following command:

Example

[ceph: root@host01 /]# podman ps -a --format json | jq '.[].Image'
"docker.io/library/rhel9"
"registry.redhat.io/rhceph-alpha/rhceph-6-rhel9@sha256:9aaea414e2c263216f3cdcb7a096f57c3adf6125ec9f4b0f5f65fa8c43987155"

14.7. Manually run containers

Cephadm writes small wrappers that runs a container. Refer to /var/lib/ceph/CLUSTER_FSID/SERVICE_NAME/unit to run the container execution command.

Analysing SSH errors

If you get the following error:

Example

execnet.gateway_bootstrap.HostNotFound: -F /tmp/cephadm-conf-73z09u6g -i /tmp/cephadm-identity-ky7ahp_5 root@10.10.1.2
...
raise OrchestratorError(msg) from e
orchestrator._interface.OrchestratorError: Failed to connect to 10.10.1.2 (10.10.1.2).
Please make sure that the host is reachable and accepts connections using the cephadm SSH key

Try the following options to troubleshoot the issue:

  • To ensure Cephadm has a SSH identity key, run the following command:

    Example

    [ceph: root@host01 /]# ceph config-key get mgr/cephadm/ssh_identity_key > ~/cephadm_private_key
    INFO:cephadm:Inferring fsid f8edc08a-7f17-11ea-8707-000c2915dd98
    INFO:cephadm:Using recent ceph image docker.io/ceph/ceph:v15 obtained 'mgr/cephadm/ssh_identity_key'
    [root@mon1 ~] # chmod 0600 ~/cephadm_private_key

    If the above command fails, Cephadm does not have a key. To generate a SSH key, run the following command:

    Example

    [ceph: root@host01 /]# chmod 0600 ~/cephadm_private_key

    Or

    Example

    [ceph: root@host01 /]# cat ~/cephadm_private_key | ceph cephadm set-ssk-key -i-

  • To ensure that the SSH configuration is correct, run the following command:

    Example

    [ceph: root@host01 /]# ceph cephadm get-ssh-config

  • To verify the connection to the host, run the following command:

    Example

    [ceph: root@host01 /]# ssh -F config -i ~/cephadm_private_key root@host01

Verify public key is in authorized_keys.

To verify that the public key is in the authorized_keys file, run the following commands:

Example

[ceph: root@host01 /]# ceph cephadm get-pub-key
[ceph: root@host01 /]# grep "`cat ~/ceph.pub`" /root/.ssh/authorized_keys

14.8. CIDR network error

Classless inter domain routing (CIDR) also known as supernetting, is a method of assigning Internet Protocol (IP) addresses,FThe Cephadm log entries shows the current state that improves the efficiency of address distribution and replaces the previous system based on Class A, Class B and Class C networks. If you see one of the following errors:

ERROR: Failed to infer CIDR network for mon ip *; pass --skip-mon-network to configure it later

Or

Must set public_network config option or specify a CIDR network, ceph addrvec, or plain IP

You need to run the following command:

Example

[ceph: root@host01 /]# ceph config set host public_network hostnetwork

14.9. Access the admin socket

Each Ceph daemon provides an admin socket that bypasses the MONs.

To access the admin socket, enter the daemon container on the host:

Example

[ceph: root@host01 /]# cephadm enter --name cephfs.hostname.ppdhsz
[ceph: root@mon1 /]# ceph --admin-daemon /var/run/ceph/ceph-cephfs.hostname.ppdhsz.asok config show

14.10. Manually deploying a mgr daemon

Cephadm requires a mgr daemon in order to manage the Red Hat Ceph Storage cluster. In case the last mgr daemon of a Red Hat Ceph Storage cluster was removed, you can manually deploy a mgr daemon, on a random host of the Red Hat Ceph Storage cluster.

Prerequisites

  • A running Red Hat Ceph Storage cluster.
  • Root-level access to all the nodes.
  • Hosts are added to the cluster.

Procedure

  1. Log into the Cephadm shell:

    Example

    [root@host01 ~]# cephadm shell

  2. Disable the Cephadm scheduler to prevent Cephadm from removing the new MGR daemon, with the following command:

    Example

    [ceph: root@host01 /]# ceph config-key set mgr/cephadm/pause true

  3. Get or create the auth entry for the new MGR daemon:

    Example

    [ceph: root@host01 /]# ceph auth get-or-create mgr.host01.smfvfd1 mon "profile mgr" osd "allow *" mds "allow *"
    [mgr.host01.smfvfd1]
    key = AQDhcORgW8toCRAAlMzlqWXnh3cGRjqYEa9ikw==

  4. Open ceph.conf file:

    Example

    [ceph: root@host01 /]# ceph config generate-minimal-conf
    # minimal ceph.conf for 8c9b0072-67ca-11eb-af06-001a4a0002a0
    [global]
    fsid = 8c9b0072-67ca-11eb-af06-001a4a0002a0
    mon_host = [v2:10.10.200.10:3300/0,v1:10.10.200.10:6789/0] [v2:10.10.10.100:3300/0,v1:10.10.200.100:6789/0]

  5. Get the container image:

    Example

    [ceph: root@host01 /]# ceph config get "mgr.host01.smfvfd1" container_image

  6. Create a config-json.json file and add the following:

    Note

    Use the values from the output of the ceph config generate-minimal-conf command.

    Example

    {
      {
      "config": "# minimal ceph.conf for 8c9b0072-67ca-11eb-af06-001a4a0002a0\n[global]\n\tfsid = 8c9b0072-67ca-11eb-af06-001a4a0002a0\n\tmon_host =  [v2:10.10.200.10:3300/0,v1:10.10.200.10:6789/0] [v2:10.10.10.100:3300/0,v1:10.10.200.100:6789/0]\n",
      "keyring": "[mgr.Ceph5-2.smfvfd1]\n\tkey = AQDhcORgW8toCRAAlMzlqWXnh3cGRjqYEa9ikw==\n"
    }
    }

  7. Exit from the Cephadm shell:

    Example

    [ceph: root@host01 /]# exit

  8. Deploy the MGR daemon:

    Example

    [root@host01 ~]# cephadm --image registry.redhat.io/rhceph-alpha/rhceph-6-rhel9:latest  deploy --fsid  8c9b0072-67ca-11eb-af06-001a4a0002a0 --name mgr.host01.smfvfd1 --config-json config-json.json

Verification

In the Cephadm shell, run the following command:

Example

[ceph: root@host01 /]# ceph -s

You can see a new mgr daemon has been added.

Red Hat logoGithubRedditYoutubeTwitter

Formazione

Prova, acquista e vendi

Community

Informazioni sulla documentazione di Red Hat

Aiutiamo gli utenti Red Hat a innovarsi e raggiungere i propri obiettivi con i nostri prodotti e servizi grazie a contenuti di cui possono fidarsi.

Rendiamo l’open source più inclusivo

Red Hat si impegna a sostituire il linguaggio problematico nel codice, nella documentazione e nelle proprietà web. Per maggiori dettagli, visita ilBlog di Red Hat.

Informazioni su Red Hat

Forniamo soluzioni consolidate che rendono più semplice per le aziende lavorare su piattaforme e ambienti diversi, dal datacenter centrale all'edge della rete.

© 2024 Red Hat, Inc.