Red Hat Summit Red Hat Summitサポートコンソール開発者トライアルの開始お問い合わせ

このコンテンツは選択した言語では利用できません。

10.7. Rebalancing Volumes

If a volume has been expanded or shrunk using the add-brick or remove-brick commands, the data on the volume needs to be rebalanced among the servers.

Note

In a non-replicated volume, all bricks should be online to perform the rebalance operation using the start option. In a replicated volume, at least one of the bricks in the replica should be online.
To rebalance a volume, use the following command on any of the servers: 
# gluster volume rebalance VOLNAME start# gluster volume rebalance VOLNAME start# gluster volume rebalance VOLNAME start
Copy to Clipboard Toggle word wrap
For example: 
# gluster volume rebalance test-volume start
Starting rebalancing on volume test-volume has been successful
Copy to Clipboard Toggle word wrap
A rebalance operation, without force option, will attempt to balance the space utilized across nodes, thereby skipping files to rebalance in case this would cause the target node of migration to have lesser available space than the source of migration. This leads to link files that are still left behind in the system and hence may cause performance issues in access when a large number of such link files are present.
Enhancements made to the file rename and rebalance operations in Red Hat Gluster Storage 2.1 update 5 requires that all the clients connected to a cluster operate with the same or later versions. If the clients operate on older versions, and a rebalance operation is performed, the following warning message is displayed and the rebalance operation will not be executed. 
volume rebalance: VOLNAME: failed: Volume VOLNAME has one or more connected clients of a version lower than Red Hat Gluster Storage-2.1 update 5. Starting rebalance in this state could lead to data loss.
Please disconnect those clients before attempting this command again.
Copy to Clipboard Toggle word wrap
Red Hat strongly recommends you to disconnect all the older clients before executing the rebalance command to avoid a potential data loss scenario.

Warning

The Rebalance command can be executed with the force option even when the older clients are connected to the cluster. However, this could lead to a data loss situation.
A rebalance operation with force, balances the data based on the layout, and hence optimizes or does away with the link files, but may lead to an imbalanced storage space used across bricks. This option is to be used only when there are a large number of link files in the system.
To rebalance a volume forcefully, use the following command on any of the servers: 
# gluster volume rebalance VOLNAME start force# gluster volume rebalance VOLNAME start force# gluster volume rebalance VOLNAME start force
Copy to Clipboard Toggle word wrap
For example: 
# gluster volume rebalance test-volume start force
Starting rebalancing on volume test-volume has been successful
Copy to Clipboard Toggle word wrap

10.7.1. Rebalance Throttling
リンクのコピー

Rebalance process is made multithreaded to handle multiple files migration for enhancing the performance. During multiple file migration, there can be a severe impact on storage system performance and a throttling mechanism is provided to manage it.
By default, the rebalance throttling is started in the normal mode. Configure the throttling modes to adjust the rate at which the files must be migrated 
# gluster volume set VOLNAME rebal-throttle lazy|normal|aggressive# gluster volume set VOLNAME rebal-throttle lazy|normal|aggressive# gluster volume set VOLNAME rebal-throttle lazy|normal|aggressive
Copy to Clipboard Toggle word wrap
For example: 
# gluster volume set test-volume rebal-throttle lazy
Copy to Clipboard Toggle word wrap

10.7.2. Displaying Status of a Rebalance Operation
リンクのコピー

To display the status of a volume rebalance operation, use the following command: 
# gluster volume rebalance VOLNAME status# gluster volume rebalance VOLNAME status# gluster volume rebalance VOLNAME status
Copy to Clipboard Toggle word wrap
For example: 
# gluster volume rebalance test-volume status
     Node    Rebalanced-files          size       scanned      failures         status
---------         -----------   -----------   -----------   -----------   ------------
localhost                 112         14567           150            0    in progress
10.16.156.72              140          2134           201            2    in progress
Copy to Clipboard Toggle word wrap
The time taken to complete the rebalance operation depends on the number of files on the volume and their size. Continue to check the rebalancing status, and verify that the number of rebalanced or scanned files keeps increasing.
For example, running the status command again might display a result similar to the following: 
# gluster volume rebalance test-volume status
     Node    Rebalanced-files          size       scanned      failures         status
---------         -----------   -----------   -----------   -----------   ------------
localhost                 112         14567           150            0    in progress
10.16.156.72              140          2134           201            2    in progress
Copy to Clipboard Toggle word wrap
The rebalance status will be shown as completed the following when the rebalance is complete: 
# gluster volume rebalance test-volume status
     Node    Rebalanced-files          size       scanned      failures         status
---------         -----------   -----------   -----------   -----------   ------------
localhost                 112         15674           170            0       completed
10.16.156.72              140          3423           321            2       completed
Copy to Clipboard Toggle word wrap

10.7.3. Stopping a Rebalance Operation
リンクのコピー

To stop a rebalance operation, use the following command: 
# gluster volume rebalance VOLNAME stop# gluster volume rebalance VOLNAME stop# gluster volume rebalance VOLNAME stop
Copy to Clipboard Toggle word wrap
For example: 
# gluster volume rebalance test-volume stop
     Node    Rebalanced-files          size       scanned      failures         status
---------         -----------   -----------   -----------   -----------   ------------
localhost                 102         12134           130            0         stopped
10.16.156.72              110          2123           121            2         stopped
Stopped rebalance process on volume test-volume
Copy to Clipboard Toggle word wrap
トップに戻る
Red Hat logoGithubredditYoutubeTwitter

詳細情報

試用、購入および販売

コミュニティー

Red Hat ドキュメントについて

Red Hat をお使いのお客様が、信頼できるコンテンツが含まれている製品やサービスを活用することで、イノベーションを行い、目標を達成できるようにします。 最新の更新を見る.

多様性を受け入れるオープンソースの強化

Red Hat では、コード、ドキュメント、Web プロパティーにおける配慮に欠ける用語の置き換えに取り組んでいます。このような変更は、段階的に実施される予定です。詳細情報: Red Hat ブログ.

会社概要

Red Hat は、企業がコアとなるデータセンターからネットワークエッジに至るまで、各種プラットフォームや環境全体で作業を簡素化できるように、強化されたソリューションを提供しています。

Theme

© 2025 Red Hat