Red Hat Summit이 콘텐츠는 선택한 언어로 제공되지 않습니다.
Chapter 26. Configure JGroups
JGroups is the underlying group communication library used to connect Red Hat JBoss Data Grid instances. For a full list of JGroups protocols supported in JBoss Data Grid, see Section A.1, “Supported JGroups Protocols”
26.1. Configure Red Hat JBoss Data Grid Interface Binding (Remote Client-Server Mode)
링크 복사링크가 클립보드에 복사되었습니다!
26.1.1. Interfaces
링크 복사링크가 클립보드에 복사되었습니다!
Red Hat JBoss Data Grid allows users to specify an interface type rather than a specific (unknown) IP address.
link-local: Uses a169.x.x.xor254.x.x.xaddress. This suits the traffic within one box.Copy to Clipboard Copied! Toggle word wrap Toggle overflow site-local: Uses a private IP address, for example192.168.x.x. This prevents extra bandwidth charged from GoGrid, and similar providers.Copy to Clipboard Copied! Toggle word wrap Toggle overflow global: Picks a public IP address. This should be avoided for replication traffic.Copy to Clipboard Copied! Toggle word wrap Toggle overflow non-loopback: Uses the first address found on an active interface that is not a127.x.x.xaddress.Copy to Clipboard Copied! Toggle word wrap Toggle overflow
26.1.2. Binding Sockets
링크 복사링크가 클립보드에 복사되었습니다!
Socket bindings provide a named the combination of interface and port. Sockets can be bound to the interface either individually or using a socket binding group.
26.1.2.1. Binding a Single Socket Example
링크 복사링크가 클립보드에 복사되었습니다!
The following is an example depicting the use of JGroups interface socket binding to bind an individual socket using the
socket-binding element.
Example 26.1. Socket Binding
<socket-binding name="jgroups-udp" <!-- Additional configuration elements here --> interface="site-local"/>
<socket-binding name="jgroups-udp" <!-- Additional configuration elements here --> interface="site-local"/>26.1.2.2. Binding a Group of Sockets Example
링크 복사링크가 클립보드에 복사되었습니다!
The following is an example depicting the use of Groups interface socket bindings to bind a group, using the
socket-binding-group element:
Example 26.2. Bind a Group
The two sample socket bindings in the example are bound to the same
default-interface (global), therefore the interface attribute does not need to be specified.
26.1.3. Configure JGroups Socket Binding
링크 복사링크가 클립보드에 복사되었습니다!
Each JGroups stack, configured in the JGroups subsystem, uses a specific socket binding. Set up the socket binding as follows:
Example 26.3. JGroups Socket Binding Configuration
Important
When using UDP as the JGroups transport, the socket binding has to specify the regular (unicast) port, multicast address, and multicast port.
'%20d='M201.5%20305.5c-13.8%200-24.9-11.1-24.9-24.6%200-13.8%2011.1-24.9%2024.9-24.9%2013.6%200%2024.6%2011.1%2024.6%2024.9%200%2013.6-11.1%2024.6-24.6%2024.6zM504%20256c0%20137-111%20248-248%20248S8%20393%208%20256%20119%208%20256%208s248%20111%20248%20248zm-132.3-41.2c-9.4%200-17.7%203.9-23.8%2010-22.4-15.5-52.6-25.5-86.1-26.6l17.4-78.3%2055.4%2012.5c0%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.3%2024.9-24.9s-11.1-24.9-24.9-24.9c-9.7%200-18%205.8-22.1%2013.8l-61.2-13.6c-3-.8-6.1%201.4-6.9%204.4l-19.1%2086.4c-33.2%201.4-63.1%2011.3-85.5%2026.8-6.1-6.4-14.7-10.2-24.1-10.2-34.9%200-46.3%2046.9-14.4%2062.8-1.1%205-1.7%2010.2-1.7%2015.5%200%2052.6%2059.2%2095.2%20132%2095.2%2073.1%200%20132.3-42.6%20132.3-95.2%200-5.3-.6-10.8-1.9-15.8%2031.3-16%2019.8-62.5-14.9-62.5zM302.8%20331c-18.2%2018.2-76.1%2017.9-93.6%200-2.2-2.2-6.1-2.2-8.3%200-2.5%202.5-2.5%206.4%200%208.6%2022.8%2022.8%2087.3%2022.8%20110.2%200%202.5-2.2%202.5-6.1%200-8.6-2.2-2.2-6.1-2.2-8.3%200zm7.7-75c-13.6%200-24.6%2011.1-24.6%2024.9%200%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.1%2024.9-24.6%200-13.8-11-24.9-24.9-24.9z'/%3e%3c/svg%3e){kind=small}