이 콘텐츠는 선택한 언어로 제공되지 않습니다.

Chapter 3. Setting Up DM-Multipath


This chapter provides step-by-step example procedures for configuring DM-Multipath. It includes the following procedures:
  • Basic DM-Multipath setup
  • Ignoring local disks
  • Adding more devices to the configuration file

3.1. Setting Up DM-Multipath

Before setting up DM-Multipath on your system, ensure that your system has been updated and includes the device-mapper-multipath package.
Use the following procedure to set up DM-Multipath for a basic failover configuration.
  1. Edit the /etc/multipath.conf file by commenting out the following lines at the top of the file. This section of the configuration file, in its initial state, blacklists all devices. You must comment it out to enable multipathing.
    devnode_blacklist {
            devnode "*"
    }
    
    After commenting out those lines, this section appears as follows.
    # devnode_blacklist {
    #        devnode "*"
    # }
    
  2. The default settings for DM-Multipath are compiled in to the system and do not need to be explicitly set in the /etc/multipath.conf file.
    The default value of path_grouping_policy is set to failover, so in this example you do not need to change the default value. For information on changing the values in the configuration file to something other than the defaults, see Chapter 4, The DM-Multipath Configuration File.
    The initial defaults section of the configuration file configures your system that the names of the multipath devices are are of the form mpathn; without this setting, the names of the multipath devices would be aliased to the WWID of the device.
  3. Save the configuration file and exit the editor.
  4. Execute the following commands:
    modprobe dm-multipath
    service multipathd start
    multipath -v2
    
    The multipath -v2 command prints out multipathed paths that show which devices are multipathed, but only for the devices created by this command. If the command does yield any output, you can check your multipath devices as follows:
    • Run the multipath -ll command. This lists all the multipath devices.
    • If running the multipath -ll command does not show the device, verify that multipath is configured properly by checking the /etc/multipath file and making sure that the SCSI devices you want to be multipathed exist on the system.
    • If the SCSI devices do not appear, ensure that all SAN connections are set up properly.
  5. Execute the following command to ensure sure that the multipath daemon starts on bootup:
    chkconfig multipathd on
    
Since the value of user_friendly_name is set to yes in the configuration filea the multipath devices will be created as /dev/mapper/mpathn. For information on setting the name of the device to an alias of your choosing, see Chapter 4, The DM-Multipath Configuration File.
Red Hat logoGithubRedditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

© 2024 Red Hat, Inc.