Red Hat SummitChapter 30. Configuring ELILO
ELILO is the boot loader used on EFI-based systems, notably Itanium®. Similar to the GRUB, the boot loader on x86 and x86-64 systems, ELILO allows the user to select which installed kernel to load during the system boot sequence. ELILO also allows the user to pass arguments to the kernel. The ELILO configuration file, which is located in the EFI boot partition and symbolically linked to
/etc/elilo.conf, contains a list of global options and image stanzas. When you install the kernel-xen RPM, a post install script adds the appropriate image stanza to the elilo.conf.
Important
This section on ELILO is for systems running the Xen kernel on the Intel Itanium architecture.
The ELILO configuration file has two sections:
- Global options that affect the behavior of ELILO and all the entries. Typically there is no need to change these from the default values.
- Image stanzas that define a boot selection along with associated options.
Here is a sample image stanza in elilo.conf:
The
image parameter indicates the following lines apply to a single boot selection. This stanza defines a hypervisor (vmm), initrd, and command line arguments (read-only, root and append) to the hypervisor and kernel. When ELILO is loaded during the boot sequence, the image is labeled linux.
ELILO translates
read-only to the kernel command line option ro which causes the root file system to be mounted read-only until the initscripts mount the root drive as read-write. ELILO copies the "root" line to the kernel command line. These are merged with the "append" line to build a complete command line:
"-- root=/dev/VolGroup00/rhel5_2 ro rhgb quiet"
"-- root=/dev/VolGroup00/rhel5_2 ro rhgb quiet"
The
-- symbols delimit hypervisor and kernel arguments. The hypervisor arguments come first, then the -- delimiter, followed by the kernel arguments. The hypervisor does not usually have any arguments.
Note
ELILO passes the entire command line to the hypervisor. The hypervisor divides the content and passes the kernel options to the kernel.
To customize the hypervisor, insert parameters before the
--. An example of the hypervisor memory (mem) parameter and the quiet parameter for the kernel:
append="dom0_mem=2G -- quiet"
append="dom0_mem=2G -- quiet"
ELILO hypervisor parameters
| Parameter | Description |
|---|---|
mem= | The mem parameter defines the hypervisor maximum RAM usage. Any additional RAM in the system is ignored. The parameter may be specified with a B, K, M or G suffix; representing bytes, kilobytes, megabytes and gigabytes respectively. If no suffix is specified the default unit is kilobytes. |
dom0_mem= | dom0_mem= sets the amount of RAM to allocate to dom0. The same suffixes are respected as for the mem parameter above. The default in Red Hat Enterprise Linux 5.2 on Itanium® is 4G. |
dom0_max_vcpus= | dom0_max_vcpus= sets the number of CPUs to allocate to the hypervisor. The default in Red Hat Enterprise Linux 5.2 on Itanium® is 4. |
com1=<baud>,DPS,<io_base>,<irq> | com1= sets the parameters for the first serial line. For example, com1=9600,8n1,0x408,5. The io_base and irq options can be omitted to leave them as the standard defaults. The baud parameter can be set as auto to indicate the boot loader setting should be preserved. The com1 parameter can be omitted if serial parameters are set as global options in ELILO or in the EFI configuration. |
com2=<baud>,DPS,<io_base>,<irq> | Set the parameters for the second serial line. Refer the description of the com1 parameter above. |
console=<specifier_list> | The console is a comma delimited preference list for the console options. Options include vga, com1 and com2. This setting should be omitted because the hypervisor attempts to inherit EFI console settings. |
A modified example of the configuration above, showing syntax for appending memory and cpu allocation parameters to the hypervisor:
Additionally this example removes the kernel parameters "
rhgb quiet" so that kernel and initscript output are generated on the console. Note the double-dash remains so that the append line is correctly interpreted as hypervisor arguments.
'%20d='M201.5%20305.5c-13.8%200-24.9-11.1-24.9-24.6%200-13.8%2011.1-24.9%2024.9-24.9%2013.6%200%2024.6%2011.1%2024.6%2024.9%200%2013.6-11.1%2024.6-24.6%2024.6zM504%20256c0%20137-111%20248-248%20248S8%20393%208%20256%20119%208%20256%208s248%20111%20248%20248zm-132.3-41.2c-9.4%200-17.7%203.9-23.8%2010-22.4-15.5-52.6-25.5-86.1-26.6l17.4-78.3%2055.4%2012.5c0%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.3%2024.9-24.9s-11.1-24.9-24.9-24.9c-9.7%200-18%205.8-22.1%2013.8l-61.2-13.6c-3-.8-6.1%201.4-6.9%204.4l-19.1%2086.4c-33.2%201.4-63.1%2011.3-85.5%2026.8-6.1-6.4-14.7-10.2-24.1-10.2-34.9%200-46.3%2046.9-14.4%2062.8-1.1%205-1.7%2010.2-1.7%2015.5%200%2052.6%2059.2%2095.2%20132%2095.2%2073.1%200%20132.3-42.6%20132.3-95.2%200-5.3-.6-10.8-1.9-15.8%2031.3-16%2019.8-62.5-14.9-62.5zM302.8%20331c-18.2%2018.2-76.1%2017.9-93.6%200-2.2-2.2-6.1-2.2-8.3%200-2.5%202.5-2.5%206.4%200%208.6%2022.8%2022.8%2087.3%2022.8%20110.2%200%202.5-2.2%202.5-6.1%200-8.6-2.2-2.2-6.1-2.2-8.3%200zm7.7-75c-13.6%200-24.6%2011.1-24.6%2024.9%200%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.1%2024.9-24.6%200-13.8-11-24.9-24.9-24.9z'/%3e%3c/svg%3e){kind=small}