검색

이 콘텐츠는 선택한 언어로 제공되지 않습니다.

3.3. Basic SystemTap Handler Constructs

download PDF
SystemTap supports the use of several basic constructs in handlers. The syntax for most of these handler constructs are mostly based on C and awk syntax. This section describes several of the most useful SystemTap handler constructs, which should provide you with enough information to write simple yet useful SystemTap scripts.

3.3.1. Variables

Variables can be used freely throughout a handler; simply choose a name, assign a value from a function or expression to it, and use it in an expression. SystemTap automatically identifies whether a variable should be typed as a string or integer, based on the type of the values assigned to it. For instance, if you set the variable var to gettimeofday_s() (as in var = gettimeofday_s()), then var is typed as a number and can be printed in a printf() with the integer format specifier (%d).
Note, however, that by default variables are only local to the probe they are used in. This means that variables are initialized, used and disposed at each probe handler invocation. To share a variable between probes, declare the variable name using global outside of the probes. Consider the following example:

Example 3.8. timer-jiffies.stp

global count_jiffies, count_ms
probe timer.jiffies(100) { count_jiffies ++ }
probe timer.ms(100) { count_ms ++ }
probe timer.ms(12345)
{
  hz=(1000*count_jiffies) / count_ms
  printf ("jiffies:ms ratio %d:%d => CONFIG_HZ=%d\n",
    count_jiffies, count_ms, hz)
  exit ()
}
Example 3.8, “timer-jiffies.stp” computes the CONFIG_HZ setting of the kernel using timers that count jiffies and milliseconds, then computing accordingly. The global statement allows the script to use the variables count_jiffies and count_ms (set in their own respective probes) to be shared with probe timer.ms(12345).

Note

The ++ notation in Example 3.8, “timer-jiffies.stp” (count_jiffies ++ and count_ms ++) is used to increment the value of a variable by 1. In the following probe, count_jiffies is incremented by 1 every 100 jiffies:
probe timer.jiffies(100) { count_jiffies ++ }
In this instance, SystemTap understands that count_jiffies is an integer. Because no initial value was assigned to count_jiffies, its initial value is zero by default.

3.3.2. Conditional Statements

In some cases, the output of a SystemTap script may be too big. To address this, you need to further refine the script's logic in order to delimit the output into something more relevant or useful to your probe.
You can do this by using conditionals in handlers. SystemTap accepts the following types of conditional statements:
If/Else Statements
Format:
if (condition)
  statement1
else
  statement2
The statement1 is executed if the condition expression is non-zero. The statement2 is executed if the condition expression is zero. The else clause (else statement2) is optional. Both statement1 and statement2 can be statement blocks.

Example 3.9. ifelse.stp

global countread, countnonread
probe kernel.function("vfs_read"),kernel.function("vfs_write")
{
  if (probefunc()=="vfs_read") 
    countread ++ 
  else 
    countnonread ++
}
probe timer.s(5) { exit() }
probe end 
{
  printf("VFS reads total %d\n VFS writes total %d\n", countread, countnonread)
}
Example 3.9, “ifelse.stp” is a script that counts how many virtual file system reads (vfs_read) and writes (vfs_write) the system performs within a 5-second span. When run, the script increments the value of the variable countread by 1 if the name of the function it probed matches vfs_read (as noted by the condition if (probefunc()=="vfs_read")); otherwise, it increments countnonread (else {countnonread ++}).
While Loops
Format:
while (condition)
  statement
So long as condition is non-zero the block of statements in statement are executed. The statement is often a statement block and it must change a value so condition will eventually be zero.
For Loops
Format:
for (initialization; conditional; increment) statement
The for loop is simply shorthand for a while loop. The following is the equivalent while loop:
initialization
while (conditional) {
   statement
   increment
}
Conditional Operators

Aside from == (is equal to), you can also use the following operators in your conditional statements:

>=
Greater than or equal to
<=
Less than or equal to
!=
Is not equal to

3.3.3. Command-Line Arguments

You can also allow a SystemTap script to accept simple command-line arguments using a $ or @ immediately followed by the number of the argument on the command line. Use $ if you are expecting the user to enter an integer as a command-line argument, and @ if you are expecting a string.

Example 3.10. commandlineargs.stp

probe kernel.function(@1) { }
probe kernel.function(@1).return { }
Example 3.10, “commandlineargs.stp” is similar to Example 3.1, “wildcards.stp”, except that it allows you to pass the kernel function to be probed as a command-line argument (as in stap commandlineargs.stp kernel function). You can also specify the script to accept multiple command-line arguments, noting them as @1, @2, and so on, in the order they are entered by the user.
Red Hat logoGithubRedditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

© 2024 Red Hat, Inc.