Red Hat Summit Red Hat Summit지원콘솔개발자평가판 시작연락처

이 콘텐츠는 선택한 언어로 제공되지 않습니다.

Appendix C. Open vSwitch Bonding Options

The Overcloud provides networking through Open vSwitch (OVS), which provides several options for bonded interfaces. In Section 8.2, “Creating a Network Environment File”, you can configure a bonded interface in the network environment file using the following parameter: 

  BondInterfaceOvsOptions:
    "bond_mode=balance-slb"
Copy to Clipboard Toggle word wrap

C.1. Choosing a Bond Mode
링크 복사

By default, you cannot use LACP with OVS-based bonds. This configuration is not supported due to a known issue with some versions of Open vSwitch. Instead, consider using bond_mode=balance-slb as a replacement for this functionality. In addition, you can still use LACP with Linux bonding in your network interface templates. For example: 

      - type: linux_bond
        name: bond1
        members:
        - type: interface
          name: nic2
        - type: interface
          name: nic3
        bonding_options: "mode=802.3ad lacp_rate=[fast|slow] updelay=1000 miimon=100"
Copy to Clipboard Toggle word wrap
  • mode - enables LACP.
  • lacp_rate - defines whether LACP packets are sent every 1 second, or every 30 seconds.
  • updelay - defines the minimum amount of time that an interface must be active before it is used for traffic (this helps mitigate port flapping outages).
  • miimon - the interval in milliseconds that is used for monitoring the port state using the driver’s MIIMON functionality.

If you still want to use LACP with OVS-base bonds, you can manually delete the following lines from each network interface configuration (NIC) file before deployment: 

    constraints:
      - allowed_pattern: "^((?!balance.tcp).)*$"
        description: |
          The balance-tcp bond mode is known to cause packet loss and
          should not be used in BondInterfaceOvsOptions.
Copy to Clipboard Toggle word wrap

After you delete the constraint from each NIC file, you can set the bond mode option in the bond interface parameter: 

  BondInterfaceOvsOptions:
    "bond_mode=balance-tcp"
Copy to Clipboard Toggle word wrap

For the technical details behind this constraint, see BZ#1267291.

For more information on Linux bonding options, see 4.5.1. Bonding Module Directives in the Red Hat Enterprise Linux 7 Networking Guide.

C.2. Bonding Options
링크 복사

The following table provides some explanation of these options and some alternatives depending on your hardware.

Expand
Table C.1. Bonding Options

bond_mode=balance-slb

Balances flows based on source MAC address and output VLAN, with periodic rebalancing as traffic patterns change. Bonding with balance-slb allows a limited form of load balancing without the remote switch’s knowledge or cooperation. SLB assigns each source MAC and VLAN pair to a link and transmits all packets from that MAC and VLAN through that link. This mode uses a simple hashing algorithm based on source MAC address and VLAN number, with periodic rebalancing as traffic patterns change. This mode is similar to mode 2 bonds used by the Linux bonding driver. This mode is used when the switch is configured with bonding but is not configured to use LACP (static instead of dynamic bonds).

bond_mode=active-backup

This mode offers active/standby failover where the standby NIC resumes network operations when the active connection fails. Only one MAC address is presented to the physical switch. This mode does not require any special switch support or configuration, and works when the links are connected to separate switches. This mode does not provide load balancing.

lacp=[active|passive|off]

Controls the Link Aggregation Control Protocol (LACP) behavior. Only certain switches support LACP. If your switch does not support LACP, use bond_mode=balance-slb or bond_mode=active-backup.

other-config:lacp-fallback-ab=true

Sets the LACP behavior to switch to bond_mode=active-backup as a fallback.

other_config:lacp-time=[fast|slow]

Set the LACP heartbeat to 1 second (fast) or 30 seconds (slow). The default is slow.

other_config:bond-detect-mode=[miimon|carrier]

Set the link detection to use miimon heartbeats (miimon) or monitor carrier (carrier). The default is carrier.

other_config:bond-miimon-interval=100

If using miimon, set the heartbeat interval in milliseconds.

bond_updelay=1000

Number of milliseconds a link must be up to be activated to prevent flapping.

other_config:bond-rebalance-interval=10000

Milliseconds between rebalancing flows between bond members. Set to zero to disable.

Important

If you experience packet drops or performance issues using Linux bonds with Provider networks, consider disabling Large Receive Offload (LRO) on the standby interfaces. Avoid adding a Linux bond to an OVS bond, as port-flapping and loss of connectivity can occur. This is a result of a packet-loop through the standby interface.

맨 위로 이동
Red Hat logoGithubredditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다. 최신 업데이트를 확인하세요.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

Theme

© 2025 Red Hat