Red Hat Summit Red Hat SummitSuporteConsoleDesenvolvedoresComeçar um testeContato

Este conteúdo não está disponível no idioma selecionado.

Chapter 12. Encrypting etcd data

12.1. About etcd encryption
Copiar o link

By default, etcd data is not encrypted in OpenShift Container Platform. You can enable etcd encryption for your cluster to provide an additional layer of data security. For example, it can help protect the loss of sensitive data if an etcd backup is exposed to the incorrect parties.

When you enable etcd encryption, the following OpenShift API server and Kubernetes API server resources are encrypted:

  • Secrets
  • Config maps
  • Routes
  • OAuth access tokens
  • OAuth authorize tokens

When you enable etcd encryption, encryption keys are created. These keys are rotated on a weekly basis. You must have these keys to restore from an etcd backup.

Note

Etcd encryption only encrypts values, not keys. Resource types, namespaces, and object names are unencrypted.

If etcd encryption is enabled during a backup, the static_kuberesources_<datetimestamp>.tar.gz file contains the encryption keys for the etcd snapshot. For security reasons, store this file separately from the etcd snapshot. However, this file is required to restore a previous state of etcd from the respective etcd snapshot.

12.2. Enabling etcd encryption
Copiar o link

You can enable etcd encryption to encrypt sensitive resources in your cluster.

Warning

Do not back up etcd resources until the initial encryption process is completed. If the encryption process is not completed, the backup might be only partially encrypted.

After you enable etcd encryption, several changes can occur:

  • The etcd encryption might affect the memory consumption of a few resources.
  • You might notice a transient affect on backup performance because the leader must serve the backup.
  • A disk I/O can affect the node that receives the backup state.

Prerequisites

  • Access to the cluster as a user with the cluster-admin role.

Procedure

  1. Modify the APIServer object: 

    $ oc edit apiserver

  2. Set the encryption field type to aescbc: 

    spec:
  encryption:
    type: aescbc
    1
    1
    The aescbc type means that AES-CBC with PKCS#7 padding and a 32 byte key is used to perform the encryption.

  3. Save the file to apply the changes.

    The encryption process starts. It can take 20 minutes or longer for this process to complete, depending on the size of your cluster.

  4. Verify that etcd encryption was successful.

    1. Review the Encrypted status condition for the OpenShift API server to verify that its resources were successfully encrypted: 

      $ oc get openshiftapiserver -o=jsonpath='{range .items[0].status.conditions[?(@.type=="Encrypted")]}{.reason}{"\n"}{.message}{"\n"}'

      The output shows EncryptionCompleted upon successful encryption: 

      EncryptionCompleted
All resources encrypted: routes.route.openshift.io

      If the output shows EncryptionInProgress, encryption is still in progress. Wait a few minutes and try again.

    2. Review the Encrypted status condition for the Kubernetes API server to verify that its resources were successfully encrypted: 

      $ oc get kubeapiserver -o=jsonpath='{range .items[0].status.conditions[?(@.type=="Encrypted")]}{.reason}{"\n"}{.message}{"\n"}'

      The output shows EncryptionCompleted upon successful encryption: 

      EncryptionCompleted
All resources encrypted: secrets, configmaps

      If the output shows EncryptionInProgress, encryption is still in progress. Wait a few minutes and try again.

    3. Review the Encrypted status condition for the OpenShift OAuth API server to verify that its resources were successfully encrypted: 

      $ oc get authentication.operator.openshift.io -o=jsonpath='{range .items[0].status.conditions[?(@.type=="Encrypted")]}{.reason}{"\n"}{.message}{"\n"}'

      The output shows EncryptionCompleted upon successful encryption: 

      EncryptionCompleted
All resources encrypted: oauthaccesstokens.oauth.openshift.io, oauthauthorizetokens.oauth.openshift.io

      If the output shows EncryptionInProgress, encryption is still in progress. Wait a few minutes and try again.

12.3. Disabling etcd encryption
Copiar o link

You can disable encryption of etcd data in your cluster.

Prerequisites

  • Access to the cluster as a user with the cluster-admin role.

Procedure

  1. Modify the APIServer object: 

    $ oc edit apiserver

  2. Set the encryption field type to identity: 

    spec:
  encryption:
    type: identity
    1
    1
    The identity type is the default value and means that no encryption is performed.

  3. Save the file to apply the changes.

    The decryption process starts. It can take 20 minutes or longer for this process to complete, depending on the size of your cluster.

  4. Verify that etcd decryption was successful.

    1. Review the Encrypted status condition for the OpenShift API server to verify that its resources were successfully decrypted: 

      $ oc get openshiftapiserver -o=jsonpath='{range .items[0].status.conditions[?(@.type=="Encrypted")]}{.reason}{"\n"}{.message}{"\n"}'

      The output shows DecryptionCompleted upon successful decryption: 

      DecryptionCompleted
Encryption mode set to identity and everything is decrypted

      If the output shows DecryptionInProgress, decryption is still in progress. Wait a few minutes and try again.

    2. Review the Encrypted status condition for the Kubernetes API server to verify that its resources were successfully decrypted: 

      $ oc get kubeapiserver -o=jsonpath='{range .items[0].status.conditions[?(@.type=="Encrypted")]}{.reason}{"\n"}{.message}{"\n"}'

      The output shows DecryptionCompleted upon successful decryption: 

      DecryptionCompleted
Encryption mode set to identity and everything is decrypted

      If the output shows DecryptionInProgress, decryption is still in progress. Wait a few minutes and try again.

    3. Review the Encrypted status condition for the OpenShift OAuth API server to verify that its resources were successfully decrypted: 

      $ oc get authentication.operator.openshift.io -o=jsonpath='{range .items[0].status.conditions[?(@.type=="Encrypted")]}{.reason}{"\n"}{.message}{"\n"}'

      The output shows DecryptionCompleted upon successful decryption: 

      DecryptionCompleted
Encryption mode set to identity and everything is decrypted

      If the output shows DecryptionInProgress, decryption is still in progress. Wait a few minutes and try again.

Red Hat logoGithubredditYoutubeTwitter

Aprender

Experimente, compre e venda

Comunidades

Sobre a documentação da Red Hat

Ajudamos os usuários da Red Hat a inovar e atingir seus objetivos com nossos produtos e serviços com conteúdo em que podem confiar. Explore nossas atualizações recentes.

Tornando o open source mais inclusivo

A Red Hat está comprometida em substituir a linguagem problemática em nosso código, documentação e propriedades da web. Para mais detalhes veja o Blog da Red Hat.

Sobre a Red Hat

Fornecemos soluções robustas que facilitam o trabalho das empresas em plataformas e ambientes, desde o data center principal até a borda da rede.

Theme

© 2026 Red HatVoltar ao topo