Pesquisar

Este conteúdo não está disponível no idioma selecionado.

4.4. device-mapper-multipath

download PDF
The device-mapper-multipath packages provide tools to manage multipath devices using the device-mapper multipath kernel module.
  • The /etc/multipath.conf has a new defaults section parameter: file_timeout. This parameter controls how many seconds multipathd will wait for a necessary file to appear while setting up a multipath device. The default is 90 seconds. Note that using the file_timeout 0 parameter will cause mutipathd to crash. (BZ#716329)
  • By default, the multipathd service starts up before the iscsi service. This provides multipathing support early in the bootup process and is necessary for multipathed iSCSI SAN boot setups. However, once started, the multipathd service adds paths as informed about them by udev. As soon as the multipathd service detects a path that belongs to a multipath device, it creates the device. If the first path that multipathd notices is a passive path, it attempts to make that path active. If it later adds a more optimal path, multipathd activates the more optimal path. In some cases, this can cause a significant overhead during a startup.
    If you are experiencing such performance problems, define the multipathd service to start after the iscsi service. This does not apply to systems where the root device is a multipathed iSCSI device, since it the system would become unbootable. To move the service start time run the following commands:
    # mv /etc/rc5.d/S06multipathd /etc/rc5.d/S14multipathd
    # mv /etc/rc3.d/S06multipathd /etc/rc3.d/S14multipathd
    
    To restore the original start time, run the following command:
    # chkconfig multipathd resetpriorities
    
    (BZ#500998)
  • When using dm-multipath, if features "1 queue_if_no_path" is specified in /etc/multipath.conf then any process that issues I/O will hang until one or more paths are restored.
    To avoid this, set no_path_retry [N] in /etc/multipath.conf (where [N] is the number of times the system should retry a path). When you do, remove the features "1 queue_if_no_path" option from /etc/multipath.conf as well.
    If you need to use "1 queue_if_no_path" and experience the issue noted here, use dmsetup to edit the policy at runtime for a particular LUN (i.e. for which all the paths are unavailable).
    To illustrate: run dmsetup message [device] 0 "fail_if_no_path", where [device] is the multipath device name (e.g. mpath2; do not specify the path) for which you want to change the policy from "queue_if_no_path" to "fail_if_no_path". (BZ#419581)
  • When a LUN is deleted on a configured storage system, the change is not reflected on the host. In such cases, lvm commands will hang indefinitely when dm-multipath is used, as the LUN has now become stale.
    To work around this, delete all device and mpath link entries in /etc/lvm/.cache specific to the stale LUN.
    To find out what these entries are, run the following command:
    ls -l /dev/mpath | grep [stale LUN]
    For example, if [stale LUN] is 3600d0230003414f30000203a7bc41a00, the following results may appear:
    lrwxrwxrwx 1 root root 7 Aug  2 10:33 /3600d0230003414f30000203a7bc41a00 -> ../dm-4
    lrwxrwxrwx 1 root root 7 Aug  2 10:33 /3600d0230003414f30000203a7bc41a00p1 -> ../dm-5
    This means that 3600d0230003414f30000203a7bc41a00 is mapped to two mpath links: dm-4 and dm-5.
    As such, the following lines should be deleted from /etc/lvm/.cache:
    /dev/dm-4 
    /dev/dm-5 
    /dev/mapper/3600d0230003414f30000203a7bc41a00
    /dev/mapper/3600d0230003414f30000203a7bc41a00p1
    /dev/mpath/3600d0230003414f30000203a7bc41a00
    /dev/mpath/3600d0230003414f30000203a7bc41a00p1
  • Running the multipath command with the -ll option can cause the command to hang if one of the paths is on a blocking device. Note that the driver does not fail a request after some time if the device does not respond.
    This is caused by the cleanup code, which waits until the path checker request either completes or fails. To display the current multipath state without hanging the command, use multipath -l instead. (BZ#214838)
Red Hat logoGithubRedditYoutubeTwitter

Aprender

Experimente, compre e venda

Comunidades

Sobre a documentação da Red Hat

Ajudamos os usuários da Red Hat a inovar e atingir seus objetivos com nossos produtos e serviços com conteúdo em que podem confiar.

Tornando o open source mais inclusivo

A Red Hat está comprometida em substituir a linguagem problemática em nosso código, documentação e propriedades da web. Para mais detalhes veja oBlog da Red Hat.

Sobre a Red Hat

Fornecemos soluções robustas que facilitam o trabalho das empresas em plataformas e ambientes, desde o data center principal até a borda da rede.

© 2024 Red Hat, Inc.