Este conteúdo não está disponível no idioma selecionado.
Chapter 4. Managing GFS
This chapter describes the tasks and commands for managing GFS and consists of the following sections:
4.1. Creating a File System
You can create a GFS file system with the
gfs_mkfs command. A file system is created on an activated LVM volume. The following information is required to execute the gfs_mkfs command:
- Lock protocol/module name. The lock protocol for a cluster is
lock_dlm. The lock protocol when GFS is acting as a local file system (one node only) islock_nolock. - Cluster name (when running as part of a cluster configuration).
- Number of journals (one journal required for each node that may be mounting the file systema.) Make sure to account for additional journals needed for future expansion, as you cannot add journals dynamically to a GFS file system.
When creating a GFS file system, you can use the
gfs_mkfs directly, or you can use the mkfs command with the -t parameter specifying a file system of type gfs, followed by the gfs file system options.
Note
Once you have created a GFS file system with the
gfs_mkfs command, you cannot decrease the size of the file system. You can, however, increase the size of an existing file system with the gfs_grow command, as described in Section 4.7, “Growing a File System”.
Usage
When creating a clustered GFS file system, you can use either of the following formats:
gfs_mkfs -pLockProtoName-tLockTableName-jNumberJournals BlockDevice
mkfs -t gfs -pLockProtoName-tLockTableName-jNumberJournals BlockDevice
When creating a local file system, you can use either of the following formats:
Note
For the Red Hat Enterprise Linux 5.5 release and later Red Hat does not support the use of GFS as a single-node file system. Red Hat will continue to support single-node GFS file systems for existing customers.
gfs_mkfs -pLockProtoName-jNumberJournals BlockDevice
mkfs -t gfs -pLockProtoName-jNumberJournals BlockDevice
Warning
Make sure that you are very familiar with using the
LockProtoName and LockTableName parameters. Improper use of the LockProtoName and LockTableName parameters may cause file system or lock space corruption.
LockProtoName- Specifies the name of the locking protocol to use. The lock protocol for a cluster is
lock_dlm. The lock protocol when GFS is acting as a local file system (one node only) islock_nolock. LockTableName- This parameter is specified for GFS file system in a cluster configuration. It has two parts separated by a colon (no spaces) as follows:
ClusterName:FSNameClusterName, the name of the Red Hat cluster for which the GFS file system is being created.FSName, the file system name, can be 1 to 16 characters long, and the name must be unique among all file systems in the cluster.
NumberJournals- Specifies the number of journals to be created by the
gfs_mkfscommand. One journal is required for each node that mounts the file system. (More journals than are needed can be specified at creation time to allow for future expansion.) BlockDevice- Specifies a volume.
Examples
In these examples,
lock_dlm is the locking protocol that the file system uses, since this is a clustered file system. The cluster name is alpha, and the file system name is mydata1. The file system contains eight journals and is created on /dev/vg01/lvol0.
[root@ask-07 ~]# gfs_mkfs -p lock_dlm -t alpha:mydata1 -j 8 /dev/vg01/lvol0
This will destroy any data on /dev/vg01/lvol0.
Are you sure you want to proceed? [y/n] y
Device: /dev/vg01/lvol0
Blocksize: 4096
Filesystem Size: 136380192
Journals: 8
Resource Groups: 2082
Locking Protocol: lock_dlm
Lock Table: alpha:mydata1
Syncing...
All Done
[root@ask-07 ~]# mkfs -t gfs -p lock_dlm -t alpha:mydata1 -j 8 /dev/vg01/lvol0
This will destroy any data on /dev/vg01/lvol0.
Are you sure you want to proceed? [y/n] y
Device: /dev/vg01/lvol0
Blocksize: 4096
Filesystem Size: 136380192
Journals: 8
Resource Groups: 2082
Locking Protocol: lock_dlm
Lock Table: alpha:mydata1
Syncing...
All Done
In these examples, a second
lock_dlm file system is made, which can be used in cluster alpha. The file system name is mydata2. The file system contains eight journals and is created on /dev/vg01/lvol1.
gfs_mkfs -p lock_dlm -t alpha:mydata2 -j 8 /dev/vg01/lvol1
mkfs -t gfs -p lock_dlm -t alpha:mydata2 -j 8 /dev/vg01/lvol1
Complete Options
Table 4.1, “Command Options:
gfs_mkfs” describes the gfs_mkfs command options.
| Flag | Parameter | Description |
|---|---|---|
-b | BlockSize | Sets the file system block size to BlockSize. Default block size is 4096 bytes. |
-D | Enables debugging output. | |
-h | Help. Displays available options. | |
-J | MegaBytes | Specifies the size of the journal in megabytes. Default journal size is 128 megabytes. The minimum size is 32 megabytes. |
-j | Number |
Specifies the number of journals to be created by the
gfs_mkfs command. One journal is required for each node that mounts the file system.
Note: More journals than are needed can be specified at creation time to allow for future expansion.
|
-p | LockProtoName |
Specifies the name of the locking protocol to use. Recognized locking protocols include:
lock_dlm — The standard locking module, required for a clustered file system.
lock_nolock — Used when GFS is acting as a local file system (one node only).
|
-O | Prevents the gfs_mkfs command from asking for confirmation before writing the file system. | |
-q | Quiet. Do not display anything. | |
-r | MegaBytes | Specifies the size of the resource groups in megabytes. Default resource group size is 256 megabytes. |
-s | Blocks | Specifies the journal-segment size in file system blocks. |
-t | LockTableName |
Used in a clustered file system. This parameter has two parts separated by a colon (no spaces) as follows:
ClusterName:FSName.
ClusterName is the name of the Red Hat cluster for which the GFS file system is being created. The cluster name is set in the /etc/cluster/cluster.conf file via the Cluster Configuration Tool and displayed at the Cluster Status Tool in the Red Hat Cluster Suite cluster management GUI.
FSName, the file system name, can be 1 to 16 characters in length, and the name must be unique among all file systems in the cluster.
|
-V | Displays command version information. |
