Chapter 4. Troubleshooting CDK

One of the startup checks verifies that the relevant driver plug-in is configured correctly. If this startup check fails, review the Setting Up the Virtualization Environment topic and configure the appropriate driver.

If you want to force CDK to start despite a failing driver plug-in check, you can instruct CDK to treat these errors as warnings:

CDK checks whether the persistent storage volume is mounted and that enough disk space is available. If the persistent storage volume, for example, uses more than 95% of the available disk space, CDK will not start.

If you want to recover the data, you can skip this test and start CDK to access the persistent volume:

$ minishift config set skip-check-storage-usage true

After the CDK VM starts, it runs several network checks to verify whether external connectivity is possible from within the CDK VM.

By default, network checks are configured to treat any errors as warnings, because of the diversity of the development environments. You can configure the network checks to optimize them for your environment.

For example, one of the network checks pings an external host. You can change the host by running the following command:

$ minishift config set check-network-ping-host <host-IP-address>

Replace <host-IP-address> with the address of your internal DNS server, proxy host, or an external host that you can reach from your machine.

Because proxy connectivity might be problematic, you can run a check that tries to retrieve an external URL. You can configure the URL by running:

$ minishift config set check-network-http-host <URL>

If you use virsh on KVM/libvirt to create snapshots in your development workflow then use minishift delete to delete the snapshots along with the VM, you might encounter the following error:

$ minishift delete
Deleting the Minishift VM...
Error deleting the VM:  [Code-55] [Domain-10] Requested operation is not valid: cannot delete inactive domain with 4 snapshots

Cause: The snapshots are stored in ~/.minishift/machines, but the definitions are stored in /var/lib/libvirt/qemu/snapshot/minishift.

Workaround: To delete the snapshots, you need to perform the following steps as root.

$ rm -rf ~/.minishift/machines

It is recommended to avoid using metadata when you create snapshots. To ensure this, you can specify the --no-metadata flag. For example:

# virsh snapshot-create-as --domain vm1 overlay1 --diskspec vda,file=/export/overlay1.qcow2 --disk-only --atomic --no-metadata

The problem is likely that the libvirtd service is not running. You can check this with the following command:

$ systemctl status libvirtd

If libvirtd is not running, start it and enable it to start on boot:

$ systemctl start libvirtd
$ systemctl enable libvirtd

The problem is likely that the virtlogd service is not running. You can check this with the following command:

$ systemctl status virtlogd

If virtlogd is not running, start it and enable it to start on boot:

$ systemctl start virtlogd
$ systemctl enable virtlogd

If you try minishift start and this error appears, ensure that you use minishift delete to delete the VMs that you created earlier. However, if this fails and you want to completely clean up CDK and start fresh, do the following:

In case all of this fails, you might want to uninstall CDK and do a fresh install of CDK.

If you use Windows, ensure that you set the --vm-driver virtualbox flag in the minishift start command. Alternatively, the problem might be an outdated version of VirtualBox.

To avoid this issue, it is recommended to use VirtualBox 5.1.12 or later.

If you run CDK with Hyper-V on Windows as a normal user or as a user with Administrator privileges, you might encounter the following error:

Error starting the VM: Error creating the VM. Error with pre-create check: "Hyper-V commands must be run as an Administrator".

Workaround: You can either add yourself to the Hyper-V Administrators group, which is recommended, or run the shell in an elevated mode.

If you are using PowerShell, you can add yourself to the Hyper-V Administrators group as follows:

You can also use the GUI to add yourself to the Hyper-V Administrators group as follows:

Now you can run the Hyper-V commands as a normal user.

For more options for Hyper-V see creating Hyper-V administrators local group.

If you try to use CDK with Hyper-V using an external virtual switch while you are connected to a VPN such as OpenVPN, CDK might fail to provision the VM.

Cause: Hyper-V networking might not route the network traffic in both directions properly when connected to a VPN.

Workaround: Disconnect from the VPN and try again after stopping the VM from the Hyper-V manager.

On Windows, the password is stored using Credential Manager. Run the following command in Command Prompt to delete the stored password:

C:\> cmdkey /delete:minishift:<username>

On Red Hat Enterprise Linux, the password is stored using the D-Bus Secret Service API provided by libsecret. Run the following command to delete the stored password:

$ secret-tool clear service minishift username <username>

On macOS, the password is stored using Keychain Access. Run the following command to delete the stored password:

$ security delete-generic-password -s minishift