Search

8.10. NIC Offloads

download PDF
The default Ethernet maximum transfer unit (MTU) is 1500 bytes, which is the largest frame size that can usually be transmitted. This can cause system resources to be underutilized, for example, if there are 3200 bytes of data for transmission, it would mean the generation of three smaller packets. There are several options, called offloads, which allow the relevant protocol stack to transmit packets that are larger than the normal MTU. Packets as large as the maximum allowable 64KiB can be created, with options for both transmitting (Tx) and receiving (Rx). When sending or receiving large amounts of data this can mean handling one large packet as opposed to multiple smaller ones for every 64KiB of data sent or received. This means there are fewer interrupt requests generated, less processing overhead is spent on splitting or combining traffic, and more opportunities for transmission, leading to an overall increase in throughput.

Offload Types

TCP Segmentation Offload (TSO)
Uses the TCP protocol to send large packets. Uses the NIC to handle segmentation, and then adds the TCP, IP and data link layer protocol headers to each segment.
UDP Fragmentation Offload (UFO)
Uses the UDP protocol to send large packets. Uses the NIC to handle IP fragmentation into MTU sized packets for large UDP datagrams.
Generic Segmentation Offload (GSO)
Uses the TCP or UDP protocol to send large packets. If the NIC cannot handle segmentation/fragmentation, GSO performs the same operations, bypassing the NIC hardware. This is achieved by delaying segmentation until as late as possible, for example, when the packet is processed by the device driver.
Large Receive Offload (LRO)
Uses the TCP protocol. All incoming packets are re-segmented as they are received, reducing the number of segments the system has to process. They can be merged either in the driver or using the NIC. A problem with LRO is that it tends to resegment all incoming packets, often ignoring differences in headers and other information which can cause errors. It is generally not possible to use LRO when IP forwarding is enabled. LRO in combination with IP forwarding can lead to checksum errors. Forwarding is enabled if /proc/sys/net/ipv4/ip_forward is set to 1.
Generic Receive Offload (GRO)
Uses either the TCP or UDP protocols. GRO is more rigorous than LRO when resegmenting packets. For example it checks the MAC headers of each packet, which must match, only a limited number of TCP or IP headers can be different, and the TCP timestamps must match. Resegmenting can be handled by either the NIC or the GSO code.

8.10.1. Using NIC Offloads

Offloads should be used on high speed systems that transmit or receive large amounts of data and favor throughput over latency. Because using offloads greatly increases the capacity of the driver queue, latency can become an issue. An example of this would be a system transferring large amounts of data using large packet sizes, but is also running lots of interactive applications. Because interactive applications send small packets at timed intervals there is a very real risk that those packets may become 'trapped' in the buffer while larger packets in front of them are processed, causing unacceptable latency.
To check current offload settings use the ethtool command. Some device settings may be listed as fixed, meaning they cannot be changed.
Command syntax: ethtool -k ethernet_device_name

Example 8.1. Check Current Offload Settings

$ ethtool -k em1
Features for em1:
rx-checksumming: on
tx-checksumming: on
tx-checksum-ipv4: off [fixed]
tx-checksum-ip-generic: on
tx-checksum-ipv6: off [fixed]
tx-checksum-fcoe-crc: off [fixed]
tx-checksum-sctp: off [fixed]
scatter-gather: on
tx-scatter-gather: on
tx-scatter-gather-fraglist: off [fixed]
tcp-segmentation-offload: on
tx-tcp-segmentation: on
tx-tcp-ecn-segmentation: off [fixed]
tx-tcp6-segmentation: on
udp-fragmentation-offload: off [fixed]
generic-segmentation-offload: on
generic-receive-offload: on
large-receive-offload: off [fixed]
rx-vlan-offload: on
tx-vlan-offload: on
ntuple-filters: off [fixed]
receive-hashing: on
highdma: on [fixed]
rx-vlan-filter: off [fixed]
vlan-challenged: off [fixed]
tx-lockless: off [fixed]
netns-local: off [fixed]
tx-gso-robust: off [fixed]
tx-fcoe-segmentation: off [fixed]
tx-gre-segmentation: off [fixed]
tx-ipip-segmentation: off [fixed]
tx-sit-segmentation: off [fixed]
tx-udp_tnl-segmentation: off [fixed]
tx-mpls-segmentation: off [fixed]
fcoe-mtu: off [fixed]
tx-nocache-copy: off
loopback: off [fixed]
rx-fcs: off
rx-all: off
tx-vlan-stag-hw-insert: off [fixed]
rx-vlan-stag-hw-parse: off [fixed]
rx-vlan-stag-filter: off [fixed]
l2-fwd-offload: off [fixed]
busy-poll: off [fixed]
Red Hat logoGithubRedditYoutubeTwitter

Learn

Try, buy, & sell

Communities

About Red Hat Documentation

We help Red Hat users innovate and achieve their goals with our products and services with content they can trust.

Making open source more inclusive

Red Hat is committed to replacing problematic language in our code, documentation, and web properties. For more details, see the Red Hat Blog.

About Red Hat

We deliver hardened solutions that make it easier for enterprises to work across platforms and environments, from the core datacenter to the network edge.

© 2024 Red Hat, Inc.