Este contenido no está disponible en el idioma seleccionado.
4.8. Adding Journals to a File System
The
gfs_jadd command is used to add journals to a GFS file system after the device where the file system resides has been expanded. Running a gfs_jadd command on a GFS file system uses space between the current end of the file system and the end of the device where the file system resides. When the fill operation is completed, the journal index is updated.
The
gfs_jadd command must be run on mounted file system, but it only needs to be run on one node in the cluster. All the other nodes sense that the expansion has occurred.
To verify that the changes were successful, use the
gfs_jadd command with the -T (test) and -v (verbose) flags. Running the command with those flags displays the current state of the mounted GFS file system.
Usage
gfs_jadd -j Number MountPointNumber- Specifies the number of new journals to be added.
MountPoint- Specifies the directory where the GFS file system is mounted.
Comments
Before running the
gfs_jadd command:
- Back up important data on the file system.
- Run a
dfcommand to display the volume used by the file system where journals will be added.MountPoint - Expand the underlying cluster volume with LVM. For information on administering LVM volumes, see the LVM Administrator's Guide
You can find out how many journals are currently used by the file system with the
gfs_tool df MountPoint command. In the following example, the file system mounted at /mnt/gfs uses 8 journals.
[root@tng3-1 gfs]# gfs_tool df /mnt/gfs
/mnt/gfs:
SB lock proto = "lock_dlm"
SB lock table = "tng3-cluster:mydata1"
SB ondisk format = 1309
SB multihost format = 1401
Block size = 4096
Journals = 8
Resource Groups = 76
Mounted lock proto = "lock_dlm"
Mounted lock table = "tng3-cluster:mydata1"
Mounted host data = "jid=0:id=196609:first=1"
Journal number = 0
Lock module flags = 0
Local flocks = FALSE
Local caching = FALSE
Oopses OK = FALSE
Type Total Used Free use%
------------------------------------------------------------------------
inodes 33 33 0 100%
metadata 38 2 36 5%
data 4980077 178 4979899 0%
After running the
gfs_jadd command, you can run the gfs_tool df MountPoint command again to check that the new journals have been added to the file system.
Examples
In this example, one journal is added to the file system that is mounted at the
/mnt/gfs directory. The underlying logical volume for this file system is extended before the journal can be added.
[root@tng3-1 ~]#lvextend -L35G /dev/gfsvg/gfslvExtending logical volume gfslv to 35.00 GB Logical volume gfslv successfully resized [root@tng3-1 ~]#gfs_jadd -j1 /mnt/gfsFS: Mount Point: /mnt/gfs FS: Device: /dev/mapper/gfsvg-gfslv FS: Options: rw,hostdata=jid=0:id=196609:first=1 FS: Size: 5242877 DEV: Size: 9175040 Preparing to write new FS information... Done.
In this example, two journals are added to the file system on the
/mnt/gfs directory.
[root@tng3-1 ~]# gfs_jadd -j2 /mnt/gfs
FS: Mount Point: /mnt/gfs
FS: Device: /dev/mapper/gfsvg-gfslv
FS: Options: rw,hostdata=jid=0:id=196609:first=1
FS: Size: 5275632
DEV: Size: 9175040
Preparing to write new FS information...
Done.
Complete Usage
gfs_jadd [Options] {MountPoint|Device} [MountPoint|Device]
MountPoint- Specifies the directory where the GFS file system is mounted.
Device- Specifies the device node of the file system.
Table 4.4, “GFS-specific Options Available When Adding Journals” describes the GFS-specific options that can be used when adding journals to a GFS file system.
| Flag | Parameter | Description |
|---|---|---|
-h | Help. Displays short usage message. | |
-J | MegaBytes | Specifies the size of the new journals in megabytes. Default journal size is 128 megabytes. The minimum size is 32 megabytes. To add journals of different sizes to the file system, the gfs_jadd command must be run for each size journal. The size specified is rounded down so that it is a multiple of the journal-segment size that was specified when the file system was created. |
-j | Number | Specifies the number of new journals to be added by the gfs_jadd command. The default value is 1. |
-T | Test. Do all calculations, but do not write any data to the disk and do not add journals to the file system. Enabling this flag helps discover what the gfs_jadd command would have done if it were run without this flag. Using the -v flag with the -T flag turns up the verbosity level to display more information. | |
-q | Quiet. Turns down the verbosity level. | |
-V | Displays command version information. | |
-v | Turns up the verbosity of messages. |
