SupportoConsoleSviluppatoriInizia una provaContatti

Questo contenuto non è disponibile nella lingua selezionata.

1.5. Configuring netconsole

If disk logging fails or using the serial console is not possible, you might need to use kernel debugging. The netconsole kernel module enables to log kernel messages to another computer over the network.
To be able to use netconsole, you need to have an rsyslog server that is properly configured on your network.

Procedure 1.1. Configuring an rsyslog server for netconsole

  1. Configure the rsyslogd daemon to listen on the 514/udp port and receive messages from the network by uncommenting the following lines in the MODULES section of the /etc/rsyslog.conf file: 
    $ModLoad imudp
$UDPServerRun 514
  2. Restart the rsyslogd service for the changes to take effect: 
    ]# systemctl restart rsyslog
  3. Verify that rsyslogd is listening on the 514/udp port: 
    ]# netstat -l | grep syslog
udp        0      0 0.0.0.0:syslog          0.0.0.0:*
udp6       0      0 [::]:syslog             [::]:*
    The 0.0.0.0:syslog and [::]:syslog values in the netstat -l output mean that rsyslogd is listening on default netconsole port defined in the /etc/services file: 
    ]$ cat /etc/services | grep syslog
syslog          514/udp
syslog-conn     601/tcp                 # Reliable Syslog Service
syslog-conn     601/udp                 # Reliable Syslog Service
syslog-tls      6514/tcp                # Syslog over TLS
syslog-tls      6514/udp                # Syslog over TLS
syslog-tls      6514/dccp               # Syslog over TLS
Netconsole is configured using the /etc/sysconfig/netconsole file, which is a part of the initscripts package. This package is installed by default and it also provides the netconsole service.
If you want to configure a sending machine, follow this procedure:

Procedure 1.2. Configuring a Sending Machine

  1. Set the value of the SYSLOGADDR variable in the /etc/sysconfig/netconsole file to match the IP address of the syslogd server. For example: 
    SYSLOGADDR=192.168.0.1
  2. Restart the netconsole service for the changes to take effect: 
    ]# systemctl restart netconsole.service
  3. Enable netconsole.service to run after rebooting the system: 
    ]# systemctl enable netconsole.service
  4. View the netconsole messages from the client in the /var/log/messages file (default) or in the file specified in rsyslog.conf. 
    ]# cat /var/log/messages

Note

By default, rsyslogd and netconsole.service use port 514. To use a different port, change the following line in /etc/rsyslog.conf to the required port number: 
$UDPServerRun <PORT>
On the sending machine, uncomment and edit the following line in the /etc/sysconfig/netconsole file: 
SYSLOGPORT=514
For more information about netconsole configuration and troubleshooting tips, see Netconsole Kernel Documentation.
Red Hat logoGithubRedditYoutubeTwitter

Formazione

Prova, acquista e vendi

Community

Informazioni sulla documentazione di Red Hat

Aiutiamo gli utenti Red Hat a innovarsi e raggiungere i propri obiettivi con i nostri prodotti e servizi grazie a contenuti di cui possono fidarsi.

Rendiamo l’open source più inclusivo

Red Hat si impegna a sostituire il linguaggio problematico nel codice, nella documentazione e nelle proprietà web. Per maggiori dettagli, visita ilBlog di Red Hat.

Informazioni su Red Hat

Forniamo soluzioni consolidate che rendono più semplice per le aziende lavorare su piattaforme e ambienti diversi, dal datacenter centrale all'edge della rete.

© 2024 Red Hat, Inc.