Este conteúdo não está disponível no idioma selecionado.

Chapter 26. Configure JGroups


JGroups is the underlying group communication library used to connect Red Hat JBoss Data Grid instances.

26.1.1. Interfaces

Red Hat JBoss Data Grid allows users to specify an interface type rather than a specific (unknown) IP address.
  • link-local: Uses a 169.x.x.x or 254.x.x.x address. This suits the traffic within one box.
    <interfaces>
        <interface name="link-local">
            <link-local-address/>
        </interface>
        ...
    </interfaces>
    Copy to Clipboard Toggle word wrap
  • site-local: Uses a private IP address, for example 192.168.x.x. This prevents extra bandwidth charged from GoGrid, and similar providers.
    <interfaces>
        <interface name="site-local">
            <site-local-address/>
        </interface>
        ...
    </interfaces>
    Copy to Clipboard Toggle word wrap
  • global: Picks a public IP address. This should be avoided for replication traffic.
    <interfaces>
        <interface name="global">
            <any-address/>
        </interface>
        ...
    </interfaces>
    Copy to Clipboard Toggle word wrap
  • non-loopback: Uses the first address found on an active interface that is not a 127.x.x.x address.
    <interfaces>
        <interface name="non-loopback">
            <not>
    	    <loopback />
    	</not>
        </interface>
    </interfaces>
    Copy to Clipboard Toggle word wrap

26.1.2. Binding Sockets

Socket bindings provide a named the combination of interface and port. Sockets can be bound to the interface either individually or using a socket binding group.

26.1.2.1. Binding a Single Socket Example

The following is an example depicting the use of JGroups interface socket binding to bind an individual socket using the socket-binding element.

Example 26.1. Socket Binding

<socket-binding name="jgroups-udp" ... interface="site-local"/>
Copy to Clipboard Toggle word wrap

26.1.2.2. Binding a Group of Sockets Example

The following is an example depicting the use of Groups interface socket bindings to bind a group, using the socket-binding-group element:

Example 26.2. Bind a Group

<socket-binding-group name="ha-sockets" default-interface="global"> 
	...
	<socket-binding name="jgroups-tcp" port="7600"/>
	<socket-binding name="jgroups-tcp-fd" port="57600"/>
	...
</socket-binding-group>
Copy to Clipboard Toggle word wrap
The two sample socket bindings in the example are bound to the same default-interface (global), therefore the interface attribute does not need to be specified.

26.1.3. Configure JGroups Socket Binding

Each JGroups stack, configured in the JGroups subsystem, uses a specific socket binding. Set up the socket binding as follows:

Example 26.3. JGroups Socket Binding Configuration

<subsystem xmlns="urn:jboss:domain:jgroups:1.2" default-stack="udp">
    <stack name="udp">
        <transport type="UDP" socket-binding="jgroups-udp">
            ...
        </transport>
        <!-- rest of protocols -->
    </stack>
</subsystem>
Copy to Clipboard Toggle word wrap

Important

When using UDP as the JGroups transport, the socket binding has to specify the regular (unicast) port, multicast address, and multicast port.
Voltar ao topo
Red Hat logoGithubredditYoutubeTwitter

Aprender

Experimente, compre e venda

Comunidades

Sobre a documentação da Red Hat

Ajudamos os usuários da Red Hat a inovar e atingir seus objetivos com nossos produtos e serviços com conteúdo em que podem confiar. Explore nossas atualizações recentes.

Tornando o open source mais inclusivo

A Red Hat está comprometida em substituir a linguagem problemática em nosso código, documentação e propriedades da web. Para mais detalhes veja o Blog da Red Hat.

Sobre a Red Hat

Fornecemos soluções robustas que facilitam o trabalho das empresas em plataformas e ambientes, desde o data center principal até a borda da rede.

Theme

© 2025 Red Hat