Red Hat Summit Red Hat SummitSuporteConsoleDesenvolvedoresComeçar um testeContato

Este conteúdo não está disponível no idioma selecionado.

5.10. Creating Distributed Dispersed Volumes

Distributed dispersed volumes support the same configurations of erasure coding as dispersed volumes. The number of bricks in a distributed dispersed volume must be a multiple of (K+M). With this release, the following configurations are supported:
  • Multiple disperse sets containing 6 bricks with redundancy level 2
  • Multiple disperse sets containing 11 bricks with redundancy level 3
  • Multiple disperse sets containing 12 bricks with redundancy level 4

Important

Distributed dispersed volume configuration is supported only on JBOD storage. For more information, see Section 20.1.2, “JBOD”.
Use gluster volume create to create different types of volumes, and gluster volume info to verify successful volume creation.
Prerequisites
Illustration of a Distributed Dispersed Volume
View larger image
Illustration of a Distributed Dispersed Volume

Figure 5.8. Illustration of a Distributed Dispersed Volume

Creating distributed dispersed volumes

Important

Red Hat recommends you to review the Distributed Dispersed Volume configuration recommendations explained in Section 11.12, “Recommended Configurations - Dispersed Volume” before creating the Distributed Dispersed volume.
  1. Run the gluster volume create command to create the dispersed volume.
    The syntax is # gluster volume create NEW-VOLNAME disperse-data COUNT [redundancy COUNT] [transport tcp | rdma | tcp,rdma] NEW-BRICK...
    The default value for transport is tcp. Other options can be passed such as auth.allow or auth.reject. See Section 11.1, “Configuring Volume Options” for a full list of parameters.

    Example 5.12. Distributed Dispersed Volume with Six Storage Servers

    # gluster volume create test-volume disperse-data 4 redundancy 2 transport tcp server1:/rhgs1/brick1 server2:/rhgs2/brick2 server3:/rhgs3/brick3 server4:/rhgs4/brick4 server5:/rhgs5/brick5 server6:/rhgs6/brick6 server1:/rhgs7/brick7 server2:/rhgs8/brick8 server3:/rhgs9/brick9 server4:/rhgs10/brick10 server5:/rhgs11/brick11 server6:/rhgs12/brick12
Creation of test-volume has been successful
Please start the volume to access data.
    Copy to Clipboard Toggle word wrap
    The above example is illustrated in Figure 5.7, “Illustration of a Dispersed Volume” . In the illustration and example, you are creating 12 bricks from 6 servers.
  2. Run # gluster volume start VOLNAME to start the volume. 
    # gluster volume start test-volume
Starting test-volume has been successful
    Copy to Clipboard Toggle word wrap

    Important

    The open-behind volume option is enabled by default. If you are accessing the distributed dispersed volume using the SMB protocol, you must disable the open-behind volume option to avoid performance bottleneck on large file workload. Run the following command to disable open-behind volume option: 
    # gluster volume set VOLNAME open-behind off
    Copy to Clipboard Toggle word wrap
    For information on open-behind volume option, see Section 11.1, “Configuring Volume Options”
  3. Run gluster volume info command to optionally display the volume information.
Voltar ao topo
Red Hat logoGithubredditYoutubeTwitter

Aprender

Experimente, compre e venda

Comunidades

Sobre a documentação da Red Hat

Ajudamos os usuários da Red Hat a inovar e atingir seus objetivos com nossos produtos e serviços com conteúdo em que podem confiar. Explore nossas atualizações recentes.

Tornando o open source mais inclusivo

A Red Hat está comprometida em substituir a linguagem problemática em nosso código, documentação e propriedades da web. Para mais detalhes veja o Blog da Red Hat.

Sobre a Red Hat

Fornecemos soluções robustas que facilitam o trabalho das empresas em plataformas e ambientes, desde o data center principal até a borda da rede.

Theme

© 2025 Red Hat