Pesquisar
SuporteConsoleDesenvolvedoresComeçar um testeContato

Este conteúdo não está disponível no idioma selecionado.

5.2. Starting the Cluster Configuration Tool

download PDF
You can start the Cluster Configuration Tool by logging in to a cluster node as root with the ssh -Y command and issuing the system-config-cluster command. For example, to start the Cluster Configuration Tool on cluster node nano-01, do the following:
  1. Log in to a cluster node and run system-config-cluster. For example: 
    $  ssh -Y root@nano-01
  .
  .
  .
# system-config-cluster
  2. If this is the first time you have started the Cluster Configuration Tool, the program prompts you to either open an existing configuration or create a new one. Click Create New Configuration to start a new configuration file (refer to Figure 5.1, “Starting a New Configuration File”).
    Starting a New Configuration File

    Figure 5.1. Starting a New Configuration File

    Note

    The Cluster Management tab for the Red Hat Cluster Suite management GUI is available after you save the configuration file with the Cluster Configuration Tool, exit, and restart the Red Hat Cluster Suite management GUI (system-config-cluster). (The Cluster Management tab displays the status of the cluster service manager, cluster nodes, and resources, and shows statistics concerning cluster service operation. To manage the cluster system further, choose the Cluster Configuration tab.)
  3. Clicking Create New Configuration causes the New Configuration dialog box to be displayed (refer to Figure 5.2, “Creating A New Configuration”). The New Configuration dialog box provides a text box for cluster name and the following checkboxes: Custom Configure Multicast and Use a Quorum Disk. In most circumstances you only need to configure the cluster name.

    Note

    Choose the cluster name carefully. The only way to change the name of a Red Hat cluster is to create a new cluster configuration with the new name.

    Custom Configure Multicast

    Red Hat Cluster software chooses a multicast address for cluster management communication among cluster nodes. If you need to use a specific multicast address, click the Custom Configure Multicast checkbox and enter a multicast address in the Address text boxes.

    Note

    IPV6 is not supported for Cluster Suite in Red Hat Enterprise Linux 5.
    If you do not specify a multicast address, the Red Hat Cluster software (specifically, cman, the Cluster Manager) creates one. It forms the upper 16 bits of the multicast address with 239.192 and forms the lower 16 bits based on the cluster ID.

    Note

    The cluster ID is a unique identifier that cman generates for each cluster. To view the cluster ID, run the cman_tool status command on a cluster node.
    If you do specify a multicast address, you should use the 239.192.x.x series that cman uses. Otherwise, using a multicast address outside that range may cause unpredictable results. For example, using 224.0.0.x (which is "All hosts on the network") may not be routed correctly, or even routed at all by some hardware.

    Note

    If you specify a multicast address, make sure that you check the configuration of routers that cluster packets pass through. Some routers may take a long time to learn addresses, seriously impacting cluster performance.

    Use a Quorum Disk

    If you need to use a quorum disk, click the Use a Quorum disk checkbox and enter quorum disk parameters. The following quorum-disk parameters are available in the dialog box if you enable Use a Quorum disk: Interval, TKO, Votes, Minimum Score, Device, Label, and Quorum Disk Heuristic. Table 5.1, “Quorum-Disk Parameters” describes the parameters.

    Important

    Quorum-disk parameters and heuristics depend on the site environment and special requirements needed. To understand the use of quorum-disk parameters and heuristics, refer to the qdisk(5) man page. If you require assistance understanding and using quorum disk, contact an authorized Red Hat support representative.

    Note

    It is probable that configuring a quorum disk requires changing quorum-disk parameters after the initial configuration. The Cluster Configuration Tool (system-config-cluster) provides only the display of quorum-disk parameters after initial configuration. If you need to configure quorum disk, consider using Conga instead; Conga allows modification of quorum disk parameters.
    Overall:
    While system-config-cluster provides several convenient tools for configuring and managing a Red Hat Cluster, the newer, more comprehensive tool, Conga, provides more convenience and flexibility than system-config-cluster. You may want to consider using Conga instead (refer to Chapter 3, Configuring Red Hat Cluster With Conga and Chapter 4, Managing Red Hat Cluster With Conga).
    Creating A New Configuration

    Figure 5.2. Creating A New Configuration

  4. When you have completed entering the cluster name and other parameters in the New Configuration dialog box, click OK. Clicking OK starts the Cluster Configuration Tool, displaying a graphical representation of the configuration (Figure 5.3, “The Cluster Configuration Tool”).
    The Cluster Configuration Tool

    Figure 5.3. The Cluster Configuration Tool

Table 5.1. Quorum-Disk Parameters
ParameterDescription
Use a Quorum Disk Enables quorum disk. Enables quorum-disk parameters in the New Configuration dialog box.
Interval The frequency of read/write cycles, in seconds.
TKO The number of cycles a node must miss in order to be declared dead.
Votes The number of votes the quorum daemon advertises to CMAN when it has a high enough score.
Minimum Score The minimum score for a node to be considered "alive". If omitted or set to 0, the default function, floor((n+1)/2), is used, where n is the sum of the heuristics scores. The Minimum Score value must never exceed the sum of the heuristic scores; otherwise, the quorum disk cannot be available.
Device The storage device the quorum daemon uses. The device must be the same on all nodes.
Label Specifies the quorum disk label created by the mkqdisk utility. If this field contains an entry, the label overrides the Device field. If this field is used, the quorum daemon reads /proc/partitions and checks for qdisk signatures on every block device found, comparing the label against the specified label. This is useful in configurations where the quorum device name differs among nodes.
Quorum Disk Heuristics
Program — The program used to determine if this heuristic is alive. This can be anything that can be executed by /bin/sh -c. A return value of 0 indicates success; anything else indicates failure. This field is required.
Score — The weight of this heuristic. Be careful when determining scores for heuristics. The default score for each heuristic is 1.
Interval — The frequency (in seconds) at which the heuristic is polled. The default interval for every heuristic is 2 seconds.
Red Hat logoGithubRedditYoutubeTwitter

Aprender

Experimente, compre e venda

Comunidades

Sobre a documentação da Red Hat

Ajudamos os usuários da Red Hat a inovar e atingir seus objetivos com nossos produtos e serviços com conteúdo em que podem confiar.

Tornando o open source mais inclusivo

A Red Hat está comprometida em substituir a linguagem problemática em nosso código, documentação e propriedades da web. Para mais detalhes veja oBlog da Red Hat.

Sobre a Red Hat

Fornecemos soluções robustas que facilitam o trabalho das empresas em plataformas e ambientes, desde o data center principal até a borda da rede.

© 2024 Red Hat, Inc.