此内容没有您所选择的语言版本。
2.3. Configuring Fencing for Cluster Members
Once you have completed the initial steps of creating a cluster and creating fence devices, you need to configure fencing for the cluster nodes. To configure fencing for the nodes after creating a new cluster and configuring the fencing devices for the cluster, follow the steps in this section. Note that you must configure fencing for each node in the cluster.
This section documents the following procedures:
2.3.1. Configuring a Single Power-Based Fence Device for a Node
Use the following procedure to configure a node with a single power-based fence device that uses a fence device named
apc
, which uses the fence_apc
fencing agent.
- Add a fence method for the node, providing a name for the fence method.
ccs -h host --addmethod method node
For example, to configure a fence method namedAPC
for the nodenode-01.example.com
in the configuration file on the cluster nodenode-01.example.com
, execute the following command:ccs -h node01.example.com --addmethod APC node01.example.com
- Add a fence instance for the method. You must specify the fence device to use for the node, the node this instance applies to, the name of the method, and any options for this method that are specific to this node:
ccs -h host --addfenceinst fencedevicename node method [options]
For example, to configure a fence instance in the configuration file on the cluster nodenode-01.example.com
that uses the APC switch power port 1 on the fence device namedapc
to fence cluster nodenode-01.example.com
using the method namedAPC
, execute the following command:ccs -h node01.example.com --addfenceinst apc node01.example.com APC port=1
You will need to add a fence method for each node in the cluster. The following commands configure a fence method for each node with the method name
APC
. The device for the fence method specifies apc
as the device name, which is a device previously configured with the --addfencedev
option, as described in Section 2.1, “Configuring Fence Devices”. Each node is configured with a unique APC switch power port number: The port number for node-01.example.com
is 1
, the port number for node-02.example.com
is 2
, and the port number for node-03.example.com
is 3
.
ccs -h node01.example.com --addmethod APC node01.example.com ccs -h node01.example.com --addmethod APC node02.example.com ccs -h node01.example.com --addmethod APC node03.example.com ccs -h node01.example.com --addfenceinst apc node01.example.com APC port=1 ccs -h node01.example.com --addfenceinst apc node02.example.com APC port=2 ccs -h node01.example.com --addfenceinst apc node03.example.com APC port=3
Example 2.1, “
cluster.conf
After Adding Power-Based Fence Methods ” shows a cluster.conf
configuration file after you have added these fencing methods and instances to each node in the cluster.
Example 2.1. cluster.conf
After Adding Power-Based Fence Methods
<cluster name="mycluster" config_version="3"> <clusternodes> <clusternode name="node-01.example.com" nodeid="1"> <fence> <method name="APC"> <device name="apc" port="1"/> </method> </fence> </clusternode> <clusternode name="node-02.example.com" nodeid="2"> <fence> <method name="APC"> <device name="apc" port="2"/> </method> </fence> </clusternode> <clusternode name="node-03.example.com" nodeid="3"> <fence> <method name="APC"> <device name="apc" port="3"/> </method> </fence> </clusternode> </clusternodes> <fencedevices> <fencedevice agent="fence_apc" ipaddr="apc_ip_example" login="login_example" name="apc" passwd="password_example"/> </fencedevices> <rm> </rm> </cluster>
Note that when you have finished configuring all of the components of your cluster, you will need to sync the cluster configuration file to all of the nodes.