此内容没有您所选择的语言版本。
9.3. Enabling MTOM
By default the Apache CXF runtime does not enable MTOM support. It sends all binary data as either part of the normal SOAP message or as an unoptimized attachment. You can activate MTOM support either programmatically or through the use of configuration.
9.3.1. Using JAX-WS APIs
Overview
Both service providers and consumers must have the MTOM optimizations enabled. The JAX-WS APIs offer different mechanisms for each type of endpoint.
Service provider
If you published your service provider using the JAX-WS APIs you enable the runtime's MTOM support as follows:
- Access the
Endpointobject for your published service.The easiest way to access theEndpointobject is when you publish the endpoint. For more information see Chapter 29, Publishing a Service. - Get the SOAP binding from the
Endpointusing itsgetBinding()method, as shown in Example 9.4, “Getting the SOAP Binding from an Endpoint”.Example 9.4. Getting the SOAP Binding from an Endpoint
// Endpoint ep is declared previously SOAPBinding binding = (SOAPBinding)ep.getBinding();
You must cast the returned binding object to aSOAPBindingobject to access the MTOM property. - Set the binding's MTOM enabled property to
trueusing the binding'ssetMTOMEnabled()method, as shown in Example 9.5, “Setting a Service Provider's MTOM Enabled Property”.Example 9.5. Setting a Service Provider's MTOM Enabled Property
binding.setMTOMEnabled(true);
Consumer
To MTOM enable a JAX-WS consumer you must do the following:
- Cast the consumer's proxy to a
BindingProviderobject.TipFor information on getting a consumer proxy see Chapter 23, Developing a Consumer Without a WSDL Contract or Chapter 26, Developing a Consumer From a WSDL Contract. - Get the SOAP binding from the
BindingProviderusing itsgetBinding()method, as shown in Example 9.6, “Getting a SOAP Binding from aBindingProvider”.Example 9.6. Getting a SOAP Binding from a
BindingProvider// BindingProvider bp declared previously SOAPBinding binding = (SOAPBinding)bp.getBinding();
- Set the bindings MTOM enabled property to
trueusing the binding'ssetMTOMEnabled()method, as shown in Example 9.7, “Setting a Consumer's MTOM Enabled Property”.Example 9.7. Setting a Consumer's MTOM Enabled Property
binding.setMTOMEnabled(true);
9.3.2. Using configuration
Overview
If you publish your service using XML, such as when deploying to a container, you can enable your endpoint's MTOM support in the endpoint's configuration file. For more information on configuring endpoint's see Part IV, “Configuring Web Service Endpoints”.
Procedure
The MTOM property is set inside the
jaxws:endpoint element for your endpoint. To enable MTOM do the following:
- Add a
jaxws:propertychild element to the endpoint'sjaxws:endpointelement. - Add a
entrychild element to thejaxws:propertyelement. - Set the
entryelement'skeyattribute tomtom-enabled. - Set the
entryelement'svalueattribute totrue.
Example
Example 9.8, “Configuration for Enabling MTOM” shows an endpoint that is MTOM enabled.
Example 9.8. Configuration for Enabling MTOM
<beans xmlns="http://www.springframework.org/schema/beans"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:jaxws="http://cxf.apache.org/jaxws"
xsi:schemaLocation="http://www.springframework.org/schema/beans
http://www.springframework.org/schema/beans/spring-beans-2.0.xsd
http://cxf.apache.org/jaxws http://cxf.apache.org/schema/jaxws.xsd">
<jaxws:endpoint id="xRayStorage"
implementor="demo.spring.xRayStorImpl"
address="http://localhost/xRayStorage">
<jaxws:properties>
<entry key="mtom-enabled" value="true"/>
</jaxws:properties>
</jaxws:endpoint>
</beans>