12.5. Additional Para-virtualized Hardware Configuration
This section will explain how to add additional virtual network or storage to a guest operating system. For more details on configuring network and storage resources on Red Hat Enterprise Linux 5 Virtualization read the document available on Emerging Technologies, Red Hat.com
12.5.1. Virtualized Network Interfaces
Perform the following steps to configure additional network devices for your guest.
Edit your guest configuration file in
/etc/xen/YourGuestName replacing YourGuestName with the name of your guest.
The original entry may look like the one below.
vif = [ "mac=00:16:3e:2e:c5:a9,bridge=xenbr0" ]
Add an additional entry to the “
vif=” section of the configuration file similar to the one seen below.
vif = [ "mac=00:16:3e:2e:c5:a9,bridge=xenbr0",
"mac=00:16:3e:2f:d5:a9,bridge=xenbr0" ]
Make sure you generate a unique MAC address for the new interface. You can use the command below.
# echo 'import virtinst.util ; print virtinst.util.randomMAC()' | python
After the guest has been rebooted perform the following step in the guest operating system. Verify the update has been added to your
/etc/modules.conf in Red Hat Enterprise Linux 3 or /etc/modprobe.conf in Red Hat Enterprise Linux 4 and Red Hat Enterprise Linux 5. Add a new alias for each new interface you added.
alias eth1 xen-vnif
Now test that each new interface you added make sure it is available inside the guest.
# ifconfig eth1
The command above should display the properties of eth1, repeat the command for eth2 if you added a third interface, and so on.
Now configure the new network interfaces with
redhat-config-network on Red Hat Enterprise Linux 3 or system-config-network on Red Hat Enterprise Linux 4 and Red Hat Enterprise Linux 5.
12.5.2. Virtual Storage Devices
Perform the following steps to configure additional virtual storage devices for your guest.
Edit your guest configuration file in
/etc/xen/YourGuestName replacing YourGuestName with the name of your guest. The original entry may look like the one below.
disk = [ "file:/var/lib/libvirt/images/rhel5_64_fv.dsk,hda,w"]
Now, add an additional entry for your new physical device, LUN, partition or volume to the “
disk=” parameter in the configuration file. Storage entities which use the para-virtualized driver resemble the entry below. The “tap:aio” parameter instructs the hypervisor to use the para-virtualized driver.
disk = [ "file:/var/lib/libvirt/images/rhel5_64_fv.dsk,hda,w",
"tap:aio:/var/lib/libvirt/images/UserStorage1.dsk,xvda,w" ]
If you want to add more entries just add them to the “
disk=” section as a comma separated list.
Note
You need to increment the letter for the '
xvd' device, that is for your second storage entity it would be 'xvdb' instead of 'xvda'.
disk = [ "file:/var/lib/libvirt/images/rhel5_64_fv.dsk,hda,w",
"tap:aio:/var/lib/libvirt/images/UserStorage1.dsk,xvda,w",
"tap:aio:/var/lib/libvirt/images/UserStorage2.dsk,xvdb,w" ]
Verify the partitions have been created and are available.
# cat /proc/partitions major minor #blocks name 3 0 10485760 hda 3 1 104391 hda1 3 2 10377990 hda2 202 0 64000 xvda 202 1 64000 xvdb 253 0 8257536 dm-0 253 1 2031616 dm-1
In the above output you can see the partition or device “
xvdb” is available to the system.
Mount the new devices and disks to local mount points and update the
/etc/fstab inside the guest to mount the devices and partitions at boot time.
# mkdir /mnt/pvdisk_xvda # mkdir /mnt/pvdisk_xvdb # mount /dev/xvda /mnt/pvdisk_xvda # mount /dev/xvdb /mnt/pvdisk_xvdb # df /mnt Filesystem 1K-blocks Used Available Use% Mounted on /dev/xvda 64000 15 63985 1% /mnt/pvdisk_xvda /dev/xvdb 64000 15 63985 1% /mnt/pvdisk_xvdb
