SupportConsoleDevelopersStart a trialContact

Chapter 5. The Ext3 File System

The ext3 file system is essentially an enhanced version of the ext2 file system. These improvements provide the following advantages:
Availability
After an unexpected power failure or system crash (also called an unclean system shutdown), each mounted ext2 file system on the machine must be checked for consistency by the e2fsck program. This is a time-consuming process that can delay system boot time significantly, especially with large volumes containing a large number of files. During this time, any data on the volumes is unreachable.
It is possible to run fsck -n on a live filesystem. However, it will not make any changes and may give misleading results if partially written metadata is encountered.
If LVM is used in the stack, another option is to take an LVM snapshot of the filesystem and run fsck on it instead.
Finally, there is the option to remount the filesystem as read only. All pending metadata updates (and writes) are then forced to the disk prior to the remount. This ensures the filesystem is in a consistent state, provided there is no previous corruption. It is now possible to run fsck -n.
The journaling provided by the ext3 file system means that this sort of file system check is no longer necessary after an unclean system shutdown. The only time a consistency check occurs using ext3 is in certain rare hardware failure cases, such as hard drive failures. The time to recover an ext3 file system after an unclean system shutdown does not depend on the size of the file system or the number of files; rather, it depends on the size of the journal used to maintain consistency. The default journal size takes about a second to recover, depending on the speed of the hardware.

Note

The only journaling mode in ext3 supported by Red Hat is data=ordered (default).
Data Integrity
The ext3 file system prevents loss of data integrity in the event that an unclean system shutdown occurs. The ext3 file system allows you to choose the type and level of protection that your data receives. With regard to the state of the file system, ext3 volumes are configured to keep a high level of data consistency by default.
Speed
Despite writing some data more than once, ext3 has a higher throughput in most cases than ext2 because ext3's journaling optimizes hard drive head motion. You can choose from three journaling modes to optimize speed, but doing so means trade-offs in regards to data integrity if the system was to fail.
Easy Transition
It is easy to migrate from ext2 to ext3 and gain the benefits of a robust journaling file system without reformatting. Refer to Section 5.2, “Converting to an Ext3 File System” for more information on how to perform this task.
The Red Hat Enterprise Linux 6 version of ext3 features the following updates:
Default Inode Sizes Changed

The default size of the on-disk inode has increased for more efficient storage of extended attributes, for example, ACLs or SELinux attributes. Along with this change, the default number of inodes created on a file system of a given size has been decreased. The inode size may be selected with the mke2fs -I option or specified in /etc/mke2fs.conf to set system wide defaults for mke2fs.

Note

If you upgrade to Red Hat Enterprise Linux 6 with the intention of keeping any ext3 file systems intact, there is no need to remake the file system.
New Mount Option: data_err

A new mount option has been added: data_err=abort. This option instructs ext3 to abort the journal if an error occurs in a file data (as opposed to metadata) buffer in data=ordered mode. This option is disabled by default (set as data_err=ignore).

More Efficient Storage Use

When creating a file system (that is, mkfs), mke2fs will attempt to "discard" or "trim" blocks not used by the file system metadata. This helps to optimize SSDs or thinly-provisioned storage. To suppress this behavior, use the mke2fs -K option.

The following sections cover creating and tuning ext3 partitions. For ext2 partitions, skip the partitioning and formatting sections below and go directly to Section 5.2, “Converting to an Ext3 File System”.

5.1. Creating an Ext3 File System

After installation, it is sometimes necessary to create a new ext3 file system. For example, if a new disk drive is added to the system, you may want to partition the drive and use the ext3 file system.
The steps for creating an ext3 file system are as follows:

Procedure 5.1. Create an ext3 file system

  1. Format the partition with the ext3 file system using mkfs.
  2. Label the file system using e2label.
Red Hat logoGithubRedditYoutubeTwitter

Learn

Try, buy, & sell

Communities

About Red Hat Documentation

We help Red Hat users innovate and achieve their goals with our products and services with content they can trust.

Making open source more inclusive

Red Hat is committed to replacing problematic language in our code, documentation, and web properties. For more details, see the Red Hat Blog.

About Red Hat

We deliver hardened solutions that make it easier for enterprises to work across platforms and environments, from the core datacenter to the network edge.

© 2024 Red Hat, Inc.