6.4. Formatting and Mounting Bricks
To create a Red Hat Gluster Storage volume, specify the bricks that comprise the volume. After creating the volume, the volume must be started before it can be mounted.
6.4.1. Creating Bricks Manually
Important
- Red Hat supports formatting a Logical Volume using the XFS file system on the bricks.
Creating a Thinly Provisioned Logical Volume
To create a thinly provisioned logical volume, proceed with the following steps:
- Create a physical volume(PV) by using the
pvcreatecommand.For example:pvcreate --dataalignment 1280K /dev/sdb
Here,/dev/sdbis a storage device.Use the correctdataalignmentoption based on your device. For more information, see Section 13.2, “Brick Configuration”Note
The device name and the alignment value will vary based on the device you are using. - Create a Volume Group (VG) from the PV using the
vgcreatecommand:For example:vgcreate --physicalextentsize 1280K rhs_vg /dev/sdb
- Create a thin-pool using the following commands:
lvcreate --thinpool VOLGROUP/thin_pool -L pool_sz --chuncksize chunk_sz --poolmetadatasize metadev_sz --zero n
For example:lvcreate --thinpool rhs_vg/rhs_pool -L 2T --chunksize 1280K --poolmetadatasize 16G --zero n
To enhance the performance of Red Hat Gluster Storage, ensure you read Chapter 13, Configuring Red Hat Gluster Storage for Enhancing Performance chapter. - Create a thinly provisioned volume from the previously created pool using the
lvcreatecommand:For example:lvcreate -V 1G -T rhs_vg/rhs_pool -n rhs_lv
It is recommended that only one LV should be created in a thin pool.
Formatting and Mounting Bricks
Format bricks using the supported XFS configuration, mount the bricks, and verify the bricks are mounted correctly. To enhance the performance of Red Hat Gluster Storage, ensure you read Chapter 13, Configuring Red Hat Gluster Storage for Enhancing Performance before formatting the bricks.
Important
Snapshots are not supported on bricks formatted with external log devices. Do not use
-l logdev=device option with mkfs.xfs command for formatting the Red Hat Gluster Storage bricks.
- Run
# mkfs.xfs -f -i size=512 -n size=8192 -d su=128K,sw=10 DEVICEto format the bricks to the supported XFS file system format. Here, DEVICE is the created thin LV. The inode size is set to 512 bytes to accommodate for the extended attributes used by Red Hat Gluster Storage. - Run
# mkdir /mountpointto create a directory to link the brick to. - Add an entry in
/etc/fstab:/dev/rhs_vg/rhs_lv/mountpoint xfs rw,inode64,noatime,nouuid 1 2
- Run
# mount /mountpointto mount the brick. - Run the
df -hcommand to verify the brick is successfully mounted:# df -h /dev/rhs_vg/rhs_lv 16G 1.2G 15G 7% /exp1
- If SElinux is enabled, then the SELinux labels that has to be set manually for the bricks created using the following commands:
# semanage fcontext -a -t glusterd_brick_t /rhgs/brick1 # restorecon -Rv /rhgs/brick1
Using Subdirectory as the Brick for Volume
You can create an XFS file system, mount them and point them as bricks while creating a Red Hat Gluster Storage volume. If the mount point is unavailable, the data is directly written to the root file system in the unmounted directory.
For example, the
/exp directory is the mounted file system and is used as the brick for volume creation. However, for some reason, if the mount point is unavailable, any write continues to happen in the /exp directory, but now this is under root file system.
To overcome this issue, you can perform the below procedure.
During Red Hat Gluster Storage setup, create an XFS file system and mount it. After mounting, create a subdirectory and use this subdirectory as the brick for volume creation. Here, the XFS file system is mounted as
/bricks. After the file system is available, create a directory called /bricks/bricksrv1 and use it for volume creation. Ensure that no more than one brick is created from a single mount. This approach has the following advantages:
- When the
/bricksfile system is unavailable, there is no longer/bricks/bricksrv1directory available in the system. Hence, there will be no data loss by writing to a different location. - This does not require any additional file system for nesting.
Perform the following to use subdirectories as bricks for creating a volume:
- Create the
bricksrv1subdirectory in the mounted file system.# mkdir /bricks/bricksrv1
Repeat the above steps on all nodes. - Create the Red Hat Gluster Storage volume using the subdirectories as bricks.
# gluster volume create distdata01 ad-rhs-srv1:/bricks/bricksrv1 ad-rhs-srv2:/bricks/bricksrv2
- Start the Red Hat Gluster Storage volume.
# gluster volume start distdata01
- Verify the status of the volume.
# gluster volume status distdata01
Reusing a Brick from a Deleted Volume
Bricks can be reused from deleted volumes, however some steps are required to make the brick reusable.
- Brick with a File System Suitable for Reformatting (Optimal Method)
- Run
# mkfs.xfs -f -i size=512 deviceto reformat the brick to supported requirements, and make it available for immediate reuse in a new volume.Note
All data will be erased when the brick is reformatted. - File System on a Parent of a Brick Directory
- If the file system cannot be reformatted, remove the whole brick directory and create it again.
Cleaning An Unusable Brick
If the file system associated with the brick cannot be reformatted, and the brick directory cannot be removed, perform the following steps:
- Delete all previously existing data in the brick, including the
.glusterfssubdirectory. - Run
# setfattr -x trusted.glusterfs.volume-id brickand# setfattr -x trusted.gfid brickto remove the attributes from the root of the brick. - Run
# getfattr -d -m . brickto examine the attributes set on the volume. Take note of the attributes. - Run
# setfattr -x attribute brickto remove the attributes relating to the glusterFS file system.Thetrusted.glusterfs.dhtattribute for a distributed volume is one such example of attributes that need to be removed.
