Red Hat Summit Red Hat SummitSupportConsoleDéveloppeursCommencer un essaiContact

Ce contenu n'est pas disponible dans la langue sélectionnée.

10.5. Starting Geo-replication on a Newly Added Brick, Node, or Volume

10.5.1. Starting Geo-replication for a New Brick or New Node
Copier lien

If a geo-replication session is running, and a new node is added to the trusted storage pool or a brick is added to the volume from a newly added node in the trusted storage pool, then you must perform the following steps to start the geo-replication daemon on the new node:
  1. Run the following command on the master node where key-based SSH authentication connection is configured, in order to create a common pem pub file. 
    # gluster system:: execute gsec_create
    Copy to Clipboard Toggle word wrap
  2. Create the geo-replication session using the following command. The push-pem and force options are required to perform the necessary pem-file setup on the slave nodes. 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL create push-pem force
    Copy to Clipboard Toggle word wrap
    For example: 
    # gluster volume geo-replication Volume1 storage.backup.com::slave-vol create push-pem force
    Copy to Clipboard Toggle word wrap

    Note

    There must be key-based SSH authentication access between the node from which this command is run, and the slave host specified in the above command. This command performs the slave verification, which includes checking for a valid slave URL, valid slave volume, and available space on the slave.
  3. After successfully setting up the shared storage volume, when a new node is added to the cluster, the shared storage is not mounted automatically on this node. Neither is the /etc/fstab entry added for the shared storage on this node. To make use of shared storage on this node, execute the following commands: 
    # mount -t glusterfs <local node's ip>:gluster_shared_storage
/var/run/gluster/shared_storage
# cp /etc/fstab /var/run/gluster/fstab.tmp
# echo "<local node's ip>:/gluster_shared_storage
/var/run/gluster/shared_storage/ glusterfs defaults 0 0" >> /etc/fstab
    Copy to Clipboard Toggle word wrap
    For more information on setting up shared storage volume, see Section 11.12, “Setting up Shared Storage Volume”.
  4. Configure the meta-volume for geo-replication: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For example: 
    # gluster volume geo-replication Volume1 storage.backup.com::slave-vol config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For more information on configuring meta-volume, see Section 10.3.5, “Configuring a Meta-Volume”.
  5. If a node is added at slave, stop the geo-replication session using the following command: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL stop
    Copy to Clipboard Toggle word wrap
  6. Start the geo-replication session between the slave and master forcefully, using the following command: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL start force
    Copy to Clipboard Toggle word wrap
  7. Verify the status of the created session, using the following command: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL status
    Copy to Clipboard Toggle word wrap
When adding a brick to the volume on an existing node in the trusted storage pool with a geo-replication session running, the geo-replication daemon on that particular node will automatically be restarted. The new brick will then be recognized by the geo-replication daemon. This is an automated process and no configuration changes are required.

10.5.3. Starting Geo-replication for a New Volume
Copier lien

To create and start a geo-replication session between a new volume added to the master cluster and a new volume added to the slave cluster, you must perform the following steps:

Prerequisites

  • There must be key-based SSH authentication without a password access between the master volume node and the slave volume node.
  1. Create the geo-replication session using the following command: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL create
    Copy to Clipboard Toggle word wrap
    For example: 
    # gluster volume geo-replication Volume1 storage.backup.com::slave-vol create
    Copy to Clipboard Toggle word wrap

    Note

    This command performs the slave verification, which includes checking for a valid slave URL, valid slave volume, and available space on the slave.
  2. Configure the meta-volume for geo-replication: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For example: 
    # gluster volume geo-replication Volume1 storage.backup.com::slave-vol config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For more information on configuring meta-volume, see Section 10.3.5, “Configuring a Meta-Volume”.
  3. Start the geo-replication session between the slave and master, using the following command: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL start
    Copy to Clipboard Toggle word wrap
  4. Verify the status of the created session, using the following command: 
    # gluster volume geo-replication MASTER_VOL SLAVE_HOST::SLAVE_VOL status
    Copy to Clipboard Toggle word wrap
Retour au début
Red Hat logoGithubredditYoutubeTwitter

Apprendre

Essayez, achetez et vendez

Communautés

À propos de la documentation Red Hat

Nous aidons les utilisateurs de Red Hat à innover et à atteindre leurs objectifs grâce à nos produits et services avec un contenu auquel ils peuvent faire confiance. Découvrez nos récentes mises à jour.

Rendre l’open source plus inclusif

Red Hat s'engage à remplacer le langage problématique dans notre code, notre documentation et nos propriétés Web. Pour plus de détails, consultez le Blog Red Hat.

À propos de Red Hat

Nous proposons des solutions renforcées qui facilitent le travail des entreprises sur plusieurs plates-formes et environnements, du centre de données central à la périphérie du réseau.

Theme

© 2025 Red Hat